Search results for "r process"
showing 10 items of 665 documents
Interior permanent magnet synchronous motors: Impact of the variability of the parameters on their efficiency
2016
In the scientific literature, various authors presented different control strategies aimed to increase the efficiency of the interior permanent magnet synchronous motors. These strategies, starting from a well-known mathematical model of the dynamic behaviour of the motor, are able to reduce the power losses acting on the magnetizing component of the stator current. However, none of the proposed approaches takes into account that, varying the working conditions of the motor, also the values of the parameters, which have an impact on the power losses, can vary. In this paper, therefore, starting from an accurate measurement of the motor characteristics for various values of speed and load, w…
Optimized Topology for High Efficiency Battery Discharge Regulator
2008
In the following years power levels of 20 kW to 50 kW will be demanded by the telecommunication satellites. It is not possible to keep 0.5 kW modules with up to 100 modules in parallel and, therefore, higher power modules must be used. A higher bus voltage seems also necessary and any voltage below 150 V and above 100 V could meet the needs. In addition, new optimized topologies that process only a part of the total power delivery can be employed to improve the efficiency. In this article, design guidelines and experimental results of a high efficiency battery discharge regulator (BDR) module based on parallel power processing are given.
In sewer processes: mathematical model development and sensitivity analysis.
2009
Until now the majority of sewer networks in Italy have been built and managed considering small as well as local wastewater treatment plants (WWTPs). However, pushed by Italian and EU regulations, centralised and large WWTPs are becoming more common in Italy. One major technical aspect caused by the changing from local to centralised WWTPs is the development of significant in-sewer processes. These processes are also emphasized by the building of long interceptor sewers characterized by high hydraulic retention times and absence of tributary sewers. In this paper a model derived from the well known WATS model (Wastewater Aerobic/anaerobic Transformation in Sewers) has been set up and applie…
Closed-loop bandwidth impact on MVSA for rotor broken bar diagnosis in IRFOC double squirrel cage induction motor drives
2013
This paper investigates the detectability of rotor broken bars in indirect rotor flux oriented control (IRFOC) for variable speed double cage induction motor drives, using vibration signature analysis techniques. The Impact of the closed loop control system cannot be neglected when the detection of rotor asymmetries in the machine is based on the signature analysis of electrical or mechanical variables. Therefore, the investigation of rotor fault components for different bandwidths of closed-loop regulators is necessary to evaluate its relevance in the above listed variables. This paper investigates the impact of the control system on relevance of the fault components computed from axial an…
Processing and Properties of Biopolymer/Polyhydroxyalkanoates Blends
2011
In this paper, the processability and the performance of a biodegradable polymer, Mater-Bi, and of its blends with either a sample of poly (hydroxy alkanoates) (PHA) or with bacterial biomass containing PHAs were compared. Adding PHA or directly the biomass containing it allows improving the processability of the matrix. Moreover, the mechanical behaviour of the systems was compared considering two different preparation methods, namely compression and injection moulding. The injection moulded samples show poorer mechanical performances than those of the compression moulded systems. The impact strength significantly improves when PHA is added while it reduces when bacterial biomass is used i…
Towards ductilization of high strength 7XXX aluminium alloys via microstructural modifications obtained by friction stir processing and heat treatmen…
2021
Abstract High strength 7XXX aluminium series reach exceptional strength, higher than all other industrial aluminium alloys. However, they suffer from a lack of ductility compared to softer series. This work presents a procedure to improve the ductility of 7475 Al alloy in high strength condition, reaching a true fracture strain of 70% at full 500 MPa T6 yield strength. Using friction stir processing (FSP) and post-FSP heat treatments, 100% of industrial rolled material T6 yield stress is maintained but a 180% increase in fracture strain is measured for the processed material. This ductility improvement is studied by in-situ synchrotron X-ray tomography and is explained by the reduction of i…
Towards Nearly Zero Energy and Environmentally Sustainable Agritourisms: The Effectiveness of the Application of the European Ecolabel Brand
2020
Tourism represents an important economic driver in Italy, being responsible for approximately 13.2% of the total GDP (a value higher than the reference European average) and for nearly 10% of the regional GDP. Among the touristic sectors, the agritourist ones show a persistent growth, experiencing in 2019 a 6.7 point percentage improvement compared to the 2017 figures. Given this situation, the transition towards a low-carbon path, affecting the building sector for some time, should also involve agritourist buildings, through the release of EU directives, member state laws, and technical rules. On the other hand, agritourism sites could be awarded the Community EU Ecolabel. Unfortunately, a…
A Review of the Water Desalination Technologies
2021
Desalination is commonly adopted nowadays to overcome the freshwater scarcity in some areas of the world if brackish water or salt water is available. Different kinds of technologies have been proposed in the last century. In this paper, the state of the mainstream solutions is reported, showing the current commercial technologies like reverse osmosis (RO), Multi-Stages Flash desalination (MSF) and Multi-Effect Distillation (MED), and the new frontiers of the research with the aim of exploiting renewable sources such as wind, solar and biomass energy. In these cases, seawater treatment plants are the same as traditional ones, with the only difference being that they use a renewable energy s…
First Characterization of Novel Silicon Carbide Detectors with Ultra-High Dose Rate Electron Beams for FLASH Radiotherapy
2023
Ultra-high dose rate (UHDR) beams for FLASH radiotherapy present significant dosimetric challenges. Although novel approaches for decreasing or correcting ion recombination in ionization chambers are being proposed, applicability of ionimetric dosimetry to UHDR beams is still under investigation. Solid-state sensors have been recently investigated as a valuable alternative for real-time measurements, especially for relative dosimetry and beam monitoring. Among them, Silicon Carbide (SiC) represents a very promising candidate, compromising between the maturity of Silicon and the robustness of diamond. Its features allow for large area sensors and high electric fields, required to avoid ion r…
Resolving gas bubbles ascending in liquid metal from low-SNR neutron radiography images
2021
We demonstrate a new image processing methodology for resolving gas bubbles travelling through liquid metal from dynamic neutron radiography images with an intrinsically low signal-to-noise ratio. Image pre-processing, denoising and bubble segmentation are described in detail, with practical recommendations. Experimental validation is presented—stationary and moving reference bodies with neutron-transparent cavities are radiographed with imaging conditions representative of the cases with bubbles in liquid metal. The new methods are applied to our experimental data from previous and recent imaging campaigns, and the performance of the methods proposed in this paper is compared against our p…