Search results for "roughness"

Behavior of Human Osteoblast Cells Cultured on Titanium Discs in Relation to Surface Roughness and Presence of Melatonin

2017

The aim of this work was to observe the behavior of osteoblast cells cultured in vitro on titanium discs in relation to disc surface roughness and the addition of melatonin to the culture medium. MG63 osteoblast cells were cultivated on 120 Grade 5 Ti divided into three groups: Group E, treated with dual acid etch; Group EP, treated with dual acid etch and calcium phosphate; and Group M, machined. Surface roughness was examined under a laser scanning confocal microscope (CLSM) and scanning electron microscopy (SEM). The proliferation and morphology of cells were determined under fluorescence microscopy and SEM. Messenger ribonucleic acid (mRNA) of different genes related to osteoblastic dif…

Spectroscopic ellipsometry applied to phase transitions in solids: possibilities and limitations

2009

The possibilities of in situ spectroscopic ellipsometry applied to phase transitions investigation in oxide thin films and crystals are examined in this work, along with the use of various parameters calculated from ellipsometric data (band gap energy Eg, refractive index n and surface roughness) together with the directly measured main ellipsometric angles psi and Delta, for the detection of phase transitions. The efficiency of spectroscopic ellipsometry on "surface" phase transition and its sensitivity to surface defects are also demonstrated.

2020

The complex surface geometries of hailstones affect their fall behavior, fall speeds, and growth. Systematic experimental investigations on the influence of the number and length of lobes on the fall velocity and the drag coefficient of hailstones were performed in the Mainz vertical wind tunnel to provide relationships for use in numerical models. For this purpose, 3D prints of four artificial lobed hailstone models as well as spheres were used. The derived drag coefficients show no dependency in the Reynolds number in the range between 25,000 and 85,000. Further, the drag coefficients were found to increase with increasing length of lobes. All lobed hailstones show higher or similar drag …

Elucidation of constant current density molecular plating

2012

Abstract The production of thin layers by means of constant current or constant voltage electrolysis in organic media is commonly known as molecular plating. Despite the fact that this method has been applied for decades and is known to be among the most efficient ones for obtaining quantitative deposition, a full elucidation of the molecular plating is still lacking. In order to get a general understanding of the process and hence set the basis for further improvements of the method, constant current density electrolysis experiments were carried out in a mixture of isopropanol and isobutanol containing millimolar amounts of HNO 3 together with [Nd(NO 3 ) 3 ·6H 2 O] used as a model electrol…

The performance of thin layers produced by molecular plating as α-particle sources

2013

Abstract Sources for α-spectroscopy studies were prepared. Constant current density molecular plating was used to produce layers containing the α-particle emitter 147 Sm. Different parameters of the molecular plating process were varied, namely the plating solvent (an isopropanol/isobutanol mixture, pyridine, and N , N -dimethylformamide), the applied deposition time (90, 180, and 360 min), and the surface roughness of the deposition substrate (ca. 10, 20, and 300 nm). Using different analytical techniques, Sm deposition yields, chemical composition of the produced surfaces, surface homogeneity, roughness and morphology were investigated. Alpha spectra were recorded with a Si solid-state de…

An Active X-Ray Spectrometer for the SELENE-2 Rover

2014

The Active X-ray Spectrometer (AXS) for the Japanese SELENE-2 rover has been proposed for elemental analysis on the lunar surface to measure the major elements: Mg, Al, Si, Ca, Ti, and Fe; the minor elements, Na, K, P, S, Cl, Cr, and Mn and the trace element Ni, all depending on their concentrations at a landing site. The elemental data of the AXS allow us to not only classification but also quantification of surface rocks on the Moon. The AXS is a compact low-weight instrument for elemental analysis based on the principle of X-ray fluorescence spectrometry using an X-ray spectrometer and two (four) pyroelectric crystals as X-Ray Generators (XRG). This paper introduces the current status of…

The effect of the slope of irregularly distributed roughness elements on turbulent wall-bounded flows

2008

Wall roughness produces a downward shift of the mean streamwise velocity profile in the log region, known as the roughness function. The dependence of the roughness function on the height and arrangement of roughness elements has been confirmed in several studies where regular rough walls were analysed; less attention has been paid to non-regular rough walls. Here, a numerical analysis of turbulent flows over irregularly shaped rough walls is performed, clearly identifying the importance of a parameter, called the effective slope (ES) of the wall corrugations, in characterizing the geometry of non-smooth irregular walls. The effective slope proves to be one of the fundamental geometric para…

A simple equation for determining sea surface emissivity in the 3–15 µm region

2009

The high level of accuracy demanded for the sea surface temperature retrieval from infrared data requires an accurate determination of directional sea surface emissivity (SSE). Previous models have permitted calculating SSEs using a physical characterization of sea surface roughness and emission. However, these result in complex equations, and make an operational application difficult. This paper presents a simple SSE algorithm based on a parametrization of one of these models, which was selected as a reference since it reproduces SSE experimental data to a reasonable level of accuracy. The parametrization provides the SSE variation with observation angle and wind speed from a given nadir S…

Estimation of the Roughness Function in Turbulent Flows Using the Slope of the Roughness

2019

In the last decades, important efforts have been made to better understand the effects of surface roughness on the mean flow. These studies have been performed investigating turbulent channel flows, turbulent boundary layers or pipe flows. The most evident effect of the roughness is the increase of the overall resistance, corresponding to a decrease of the mean streamwise velocity profile in the logarithmic region. This reduction is known as roughness function \(\varDelta U^+\) (the symbol \(^+\) represents quantities made non dimensional using the friction velocity \(u_{\tau }\), or the viscous length scale \(\nu /u_{\tau }\)).

DEGRADATION OF MATER-BI /WOOD FLOUR BIOCOMPOSITES IN ACTIVE SEWAGE SLUDGE

2009

The mechanical properties of Mater-Bi® are, in general, not adequate for certain applications and the addition of a filler is therefore necessary. Among the different fillers, natural fibres are particularly interesting because they potentially allow improving the performance of the material without compromising its biodegradability. In order to improve the basic mechanical properties of a Mater-Bi grade and to obtain a new, fully biodegradable material, wood flour based composites were prepared by different processing methods. To simulate actual and not laboratory bacterial attack on the prepared materials, in this work we studied the biodegradation of the composites in a real active sewag…