Search results for "sintering"
showing 10 items of 165 documents
Elaboration of metal / ceramic functionally graded materials by SPS for ballistic protection
2016
The objective is to improve ballistic performance of armors. A perfect armor combines ductility to resistto the impact and high hardness to stop projectile’s fragments. However, such an association of properties is inconsistent witha single material. The solution is to perform a functionally graded material (FGM) with a ductile metal at the back side of thesample and a hard ceramic on the top side. Non-conventional technologies like Spark Plasma Sintering allow joining orsintering all types of materials with different and additional properties. Furthermore, with this technique, high heating ratescan be achieved, limiting grain growth and resulting in a fine microstructure. The goal is to st…
Microstructure and mechanical effects of spark plasma sintering in alumina monolithic ceramics
2013
The specific effects of spark plasma sintering (SPS) on the creep behavior, microstructure and mechanical properties of alumina monolithic ceramic were investigated. SPS introduces strains that concentrate at grain boundaries and inhibit crack growth, resulting in an improvement in the flexural strength and fracture toughness. However, creep blocks grain boundary movements and decreases the reliability of the material. These strains can be removed by a post-sintering thermal treatment, which plays an important role in the distribution of dislocations.
Investigation on Ash Slagging Characteristics During Combustion of Biomass Pellets and Effect of Additives
2017
This study reports a systematic investigation into ash slagging behavior during combustion of barley straw and barley husk pellets with or without additives in a residential pellet burner. The slagging tendencies of the pellets were evaluated based on the amount, chemistry, mineralogy, and morphology of inlet ash formed as slag and sintering degrees of residual ash. The barley straw and husk pellets showed high slagging tendencies with 39 and 54 wt % ingoing ash formed as slag. Analyses using X-ray fluorescence and scanning electron microcopy combined with energy-dispersive X-ray spectroscopy revealed high concentrations of K, Si, and Ca but a minor amount of P in barley straw slag. The sla…
Spark Plasma Sintering (SPS)-Assisted Synthesis and Thermoelectric Characterization of Magnéli Phase V6O11
2018
The Magneli phase V6O11 was synthesized in gram amounts from a powder mixture of V6O11/V7O13 and vanadium metal, using the spark plasma sintering (SPS) technique. Its structure was determined with synchrotron X-ray powder diffraction data from a phase-pure sample synthesized by conventional solid-state synthesis. A special feature of Magneli-type oxides is a combination of crystallographic shear and intrinsic disorder that leads to relatively low lattice thermal conductivities. SPS prepared V6O11 has a relatively low thermal conductivity of κ = 2.72 ± 0.06 W (m K)-1 while being a n-type conductor with an electrical conductivity of σ = 0.039 ± 0.005 (μΩ m)-1, a Seebeck coefficient of α = -(3…
On the use of SLS tools in sheet metal stamping
2003
Abstract A few rapid tooling technologies have been recently proposed and among them Selective Laser Sintering is probably one of the most relevant and promising. In the paper, the authors report some results of a wide experimental research on the application of SLS tools in sheet metal forming. A wear test was earned out to investigate the progressive degradation of laser-sintered materials in comparison with traditional cold-work steels. In particular SLS tools were utilized in a sheet metal stamping process of S-shaped parts: their performances (in terms of tool wear and dimensional quality of the stamped part) were compared with the ones of traditional tools.
Sintering of copper nanopowders under hydrogen: an in situ X-ray diffraction analysis.
2003
Abstract The reduction by hydrogen gas of the cuprite layer on copper nanocrystals and the subsequent sintering of the nano-particles were studied using in-situ X-ray diffraction and dilatometry. Spherical nanocrystals produced by evaporation and condensation have an average size of 35 nm, exhibiting a large surface curvature. Each nanoparticle is coated with a 3.5 nm layer of Cu 2 O, which is rough and disordered, as revealed by high-resolution electron microscopy. Reduction by hydrogen of this curved cuprite layer occurs at 363 K, which is ≈65 K lower than is observed on a layer supported by micrometer-sized or bulk copper with a flat surface. The reduction process and its effect on the s…
Effect of current on the sintering of pre-oxidized copper powders by SPS
2017
Abstract As mentioned in the literature, SPS (Spark Plasma Sintering) technology combines uniaxial charge and pulsed currents to achieve the rapid sintering of powders. Although the utilization of current is often reported, an understanding of its role in the sintering mechanisms is still a subject of controversy. In fact, the oxide layer around metal particles is sometimes considered to be a dielectric gap in which discharges may occur: these discharges can clean the surface of particles and enhance densification. In this paper, an oxide layer was grown on the particle surface of a copper powder, and the growth enabled the study of the role of current on such dielectric layers. The powders…
Thermally Induced Structural Modification of Silica Nanoparticles Investigated by Raman and Infrared Absorption Spectroscopies
2010
We report an experimental investigation by Raman and infrared (IR) absorption spectroscopies on the structural modifications induced by isochronal thermal treatments on amorphous SiO2 nanoparticles (fumed silica). In particular, three different commercial types of this material, characterized by particle mean diameters of 7, 14, and 40 nm, were subjected to thermal treatments from 100 up to 1000 °C. We found that some properties of fumed silica, such as the SiOSi mean bond angle, ring size distribution, and surface adsorbed water content, are drastically different from those of common bulk silica materials and intimately related to the particles' dimension. The SiOSi mean bond angle, probed…
SPS-assisted preparation of the Magnéli phase WO2.90 for thermoelectric applications
2013
We describe the preparation and simultaneous consolidation of WO2.90 by spark plasma sintering (SPS). SPS allows for the direct manufacturing of large amounts of consolidated material. Synchrotron powder X-ray diffraction indicates that the material is single phase. Microstructure analysis indicates that the pellet is fully dense, allowing high-temperature thermoelectric properties to be reliably measured. The as-prepared samples of WO2.90 reach a ZT of 0.1 at 1100 K.
Time-resolved XRD experiments for a fine description of mechanisms induced during reactive sintering
2005
The control of Mechanically Activated Field Activated Pressure Assisted Synthesis hereafter called the MAFAPAS process is the main objective to be achieved for producing nanostructure materials with a controlled consolidation level. Consequently, it was essential to develop characterization tools "in situ" such as the Time Resolved X-ray Diffraction (TRXRD), with an X-ray synchrotron beam (H10, LURE Orsay) coupled to an infrared thermography to study simultaneously structural transformations and thermal evolutions. From the 2003 experiments, we took the opportunity to modify the sample-holder in order to reproduce the better synthesis conditions of the MAFAPAS process, but without the conso…