Search results for "spinel"
showing 10 items of 103 documents
Cobalt aluminate spinel-mullite composites synthesized by sol-gel method
1997
Abstract CoAl 2 O 4 spinel-mullite composites were prepared by double substitution of Al by Ti and Ni in stoichiometric 3:2 mullite. Gels with compositions 3(Al 2 − 2 x Co x Ti x O 3 )·2SiO 2 (x = 0.025, 0.05 and 0.2) and 3(Al 2 − 2 x M x O 3 )·2SiO 2 (x = 0.05; M = Co 2+ or Ti 4+ ) were synthesized by sol-gel techniques. The structure of the gels was investigated by infra-red spectroscopy. Heating gels at 750 °C produced an amorphous silicoaluminate network. The reaction sequence was investigated by differential thermal analysis, X-ray diffraction and ultraviolet-visible spectroscopy. All samples crystallized at temperatures lower than 1000 °C from the amorphous state. Al-Si spinel and/or …
Mixed-Valence Defect Ferrites : a New Family of Fine Powders and Thin Films of Spinel Ferrites
1997
When highly divided spinel ferrites become reactive enough with oxygen, to allow the oxidation of the Fe 2+ ions at low temperature and of substitute cations too, when these cations are capable of different valence states. We prepared fine particles of spinel ferrites substituted by Mn, Mo, Cu, by chimie douce, especially from oxalate precursors and used them to reveal and to study the oxido-reduction phenomena occurring in these finely divided materials. It was shown that the oxidation created a new family of spinel ferrites : the mixed-valence defect ferrites, having specific characteristics and properties. The ferrites of this type can be fine powders prepared at low temperature, or grou…
Cobalt ferrite nanoparticles under high pressure
2015
We report by the first time a high pressure X-ray diffraction and Raman spectroscopy study of cobalt ferrite (CoFe2O4) nanoparticles carried out at room temperature up to 17 GPa. In contrast with previous studies of nanoparticles, which proposed the transition pressure to be reduced from 20–27 GPa to 7.5–12.5 GPa (depending on particle size), we found that cobalt ferrite nanoparticles remain in the spinel structure up to the highest pressure covered by our experiments. In addition, we report the pressure dependence of the unit-cell parameter and Raman modes of the studied sample. We found that under quasi-hydrostatic conditions, the bulk modulus of the nanoparticles (B0 = 204 GPa) is consid…
High-pressure crystal structure investigation of synthetic Fe2SiO4 spinel.
2011
AbstractThe crystal structure of Fe2SiO4 spinel at room temperature was investigated at seven different pressures by X-ray diffraction, using a diamond anvil cell to examine the influence of Fe substitution on ringwoodite behaviour at high pressure. The results compared with those of a pure Mg endmember show that the substitution of Fe into the spinel structure causes only small changes in the compression rate of coordination polyhedra and the distortion of the octahedron. The data show that the compression rate for the octahedron and tetrahedron in (Mg,Fe)2SiO4 can be considered statistically equal for FeO6 and MgO6, as well as for SiO4 in both the endmembers. This shows why almost identic…
Effect of doping and crystallite size on the electrochemical performance of Li4Ti5O12
2016
Abstract Defect spinel phase lithium titanate (Li 4 Ti 5 O 12 ) has been suggested as a promising negative electrode material for next generation lithium ion batteries. Flame spray pyrolysis has been shown to be a viable fast, one-step process for synthesis of nanoparticulate Li 4 Ti 5 O 12 . However, due to the rapid quenching that is integral to the process the crystallite size remain very small and non-uniform. To overcome this shortcoming a vertical flow tube furnace was used to increase the high-temperature residence time. This resulted in an increase in the crystallite size and crystallinity of the product. As a result of this increase the electrochemical performance of the Li 4 Ti 5 …
Atomic layer deposition of LixTiyOz thin films
2013
Atomic layer deposition (ALD) was employed to deposit ternary films of LixTiyOz. The film growth at a deposition temperature of 225 °C was studied using both titanium tetra-isoropoxide (Ti(OiPr)4) and titanium tetrachloride (TiCl4) as titanium precursors. Lithium tert-butoxide (LiOtBu) was applied as the lithium source and water was used as the oxygen source for all metal precursors. The type of titanium precursor chosen strongly affected film growth: with TiCl4 the resulting LixTiyOz films were highly air-sensitive and the lithium concentration was low, whereas with Ti(OiPr)4 the films were relatively stable in air and with a lithium content which was easily controlled over a wide range. F…
Thermal decomposition of chromite spinel with chlorite admixture
2008
Abstract The behaviour of minerals in a South African chromite ore during the increasing of the temperature has been studied. Firstly, the changes produced during the ignition process have been examined by means of thermal and differential analysis (TGA–DTA) until 1200 °C. The characterization of the initial mineral and those obtained after heating at several temperatures in room atmosphere has been performed by X-ray diffraction (XRD). Moreover, voltammetric analyses have allowed to determine the variation of the iron oxidation degree in the studied materials. Light microscopy was applied to find more information about the different phases by their colour. During the heating, a wide range …
Analytical and mineralogical studies of ore and impurities from a chromite mineral using X-ray analysis, electrochemical and microscopy techniques
2007
A wide analytical study of South African chromite ore, material with high interest in ceramic industry, has been carried out. With this purpose, an accurate chemical identification and mineralogical characterization of the mineral and the gangue have been performed using X-ray fluorescence (XRF), voltammetry, X-ray diffraction (XRD), light microscopy (LM), and scanning electron microscopy (SEM/EDX). The elemental composition of the sample (ore and gangue) has been obtained by XRF. The voltammetric analysis has allowed to demonstrate that iron in the sample was as Fe(II). The main compound of the chromite ore was a spinel (magnesiochromite ferroan), identified by XRD from the sample, which c…
Structural, Spectroscopic and Electrical Features of Undoped and Mn Doped LiTi2(PO4)3
2010
The study of the ionic conducting material LiTi2(PO 4)3 and of its Mn-substituted derivate reveals that the Mn distribution is strictly related to the synthetic method. The results of the structural refinement of X-ray and neutron (ToF) powder diffraction data and of XPS analysis demonstrate that Mn2+ ions are located on the lithium octahedral site, while Mn3+ and Mn4+ ions occupy the titanium ones. The Mn2+ amount on the lithium site seems to be the main factor responsible for the conductivity decrease observed in doped samples. The EPR spectra evidence clustering effects of Mn on both Li and Ti sites and the presence of more insulated Mn2+ ions. The effect of the major Mn amount on Ti sit…
Reaction Sequence in the Preparation of NiAl2O4 Spinel-Mullite Composites by Sol-Gel
2005
NiAl 2 O 4 spinel-mullite composites were prepared by simultaneous replacement of Al by Ti and/or Ni in 3:2 stoichiometric mullite. Specimens having nominal compositions 3(Al 2-2x Ni x Ti x O 3 ).2SiO 2 (x = 0, 0.025, 0.05, 0.2) and 3(Al 2-x M x O 3) .2SiO 2 (M = Ni 2+ or Ti 4+ and x = 0.05) were synthesized by sol-gel techniques, which provide homogeneous gels in the SiO 2 -Al 2 O 3 system. Gel structures investigated by infrared (IR) spectroscopy revealed the formation of Al-O-Si bonds in dried gels. The reaction sequence of gel-derived glasses, previously obtained by preheating gels at 750°C for 3 h, was evaluated by X-ray powder diffraction (XRD) and ultraviolet-visible (UV-vis) spectro…