Search results for "techno"
showing 10 items of 31274 documents
Aqueous Corrosion of the GeSe4 Chalcogenide Glass: Surface Properties and Corrosion Mechanism
2009
International audience; The aqueous corrosion behavior of the GeSe4 glass composition has been studied over time under various conditions (temperature and pH). The evolution of the surface topography by atomic force microscopy and properties such as surface hardness and reduced modulus, as well as the optical transmission in the 1-16 μm window, have been measured as a function of time spent in the corrosive solution. It was found that even if the glass reacts at room temperature, its optical transparency was barely affected. Nevertheless, the durability of GeSe4 was found to be drastically affected by an increase of both temperature and pH. Furthermore, pure selenium nanoparticles were form…
Microfabricated high temperature sensing platform dedicated to scanning thermal microscopy (SThM)
2018
Abstract The monitoring of heat flux is becoming more and more critical for many materials and structures approaching nanometric dimensions. Scanning Thermal Microscopy (SThM) is one of the tools available for thermal measurement at the nanoscale and requires calibration. Here we report on a micro-hotplate device made of a platinum heater suspended on thin silicon nitride (SiN) membranes integrating specific features for SThM calibration. These heated reference samples can include a localized resistive temperature sensors (RTD) or standalone platinum membranes (typically 10 × 10 μm2) on which the temperature can be measured precisely. This functional area is dedicated to (1) estimate the th…
Measurement of the activation energies of oxygen ion diffusion in yttria stabilized zirconia by flicker noise spectroscopy
2019
The low-frequency noise in a nanometer-sized virtual memristor consisting of a contact of a conductive atomic force microscope (CAFM) probe to an yttria stabilized zirconia (YSZ) thin film deposited on a conductive substrate is investigated. YSZ is a promising material for the memristor application since it is featured by high oxygen ion mobility, and the oxygen vacancy concentration in YSZ can be controlled by varying the molar fraction of the stabilizing yttrium oxide. Due to the low diameter of the CAFM probe contact to the YSZ film (similar to 10nm), we are able to measure the electric current flowing through an individual filament both in the low resistive state (LRS) and in the high r…
Parameter sensitivity of flux-linkage based sensorless control for permanent magnet synchronous motors
2017
Sensorless control can be utilized to reduce cost, size and total complexity of a motor drive or enhance reliability of the system. This paper first presents a sensorless control algorithm for a surface permanent-magnet synchronous motor (SPMSM) based on estimated flux linkages and stator currents. Within the algorithm, rotor position error can be predicted by comparing the estimated currents with measured stator currents. Performance of the sensorless control based on flux-linkages and the dependency of the algorithm on motor parameters is then numerically investigated via simulations. It is found from the investigation that the accuracy of the method depends on the motor working condition…
A Novel Fault-Tolerant Routing Algorithm for Mesh-of-Tree Based Network-on-Chips
2019
Use of bus architecture based communication with increasing processing elements in System-on-Chip (SoC) leads to severe degradation of performance and speed of the system. This bottleneck is overcome with the introduction of Network-on-Chips (NoCs). NoCs assist in communication between cores on a single chip using router based packet switching technique. Due to miniaturization, NoCs like every Integrated circuit is prone to different kinds of faults which can be transient, intermittent or permanent. A fault in any one component of such a crucial network can degrade performance leaving other components non-usable. This paper presents a novel Fault-Tolerant routing Algorithm for Mesh-of-Tree …
Interface evolution during magnetic pulse welding under extremely high strain rate collision: mechanisms, thermomechanical kinetics and consequences
2020
Abstract Magnetic pulse welding enables to produce perplexing interfacial morphologies due to the complex material response during the high strain rate collision. Thus, a thermomechanical model is used in this study to investigate the formation mechanism of the wake, vortex, swirling and mesoscale cavities with the increase of the impact intensity at the interface. The formation of these interfacial features are difficult to characterize by insitu methods, thus the origin of phenomena still remain a subject of open discussion. Our studies identify the governing mechanisms and the associated thermomechanical kinetics, which are responsible for the formation mechanism of interfacial features.…
Data-driven Fault Diagnosis of Induction Motors Using a Stacked Autoencoder Network
2019
Current signatures from an induction motor are normally used to detect anomalies in the condition of the motor based on signal processing techniques. However, false alarms might occur if using signal processing analysis alone since missing frequencies associated with faults in spectral analyses does not guarantee that a motor is fully healthy. To enhance fault diagnosis performance, this paper proposes a machinelearning based method using in-built motor currents to detect common faults in induction motors, namely inter-turn stator winding-, bearing- and broken rotor bar faults. This approach utilizes single-phase current data, being pre-processed using Welch’s method for spectral density es…
Determination of impurity distributions in ingots of solar grade silicon by neutron activation analysis
2017
AbstractIn a series of crystallization experiments, the directional solidification of silicon was investigated as a low cost path for the production of silicon wafers for solar cells. Instrumental neutron activation analysis was employed to measure the influence of different crystallization parameters on the distribution of 3d-metal impurities of the produced ingots. A theoretical model describing the involved diffusion and segregation processes during the solidification and cooling of the ingots could be verified by the experimental results. By successive etching of the samples after the irradiation, it could be shown that a layer of at least 60 μm of the samples has to be removed to get r…
Refractive index controlled by film morphology and free carrier density in undoped ZnO through sol-pH variation
2018
Abstract Zinc oxide thin films, prepared by the sol-gel process, were deposited on glass substrate using spin coating technique. The sol-pH effect on the optical parameters was studied for alkaline sol. The surface roughness was investigated by atomic force microscopy (AFM) and varied from 20 to 40 nm. The optical transmission measurements were carried out to evaluate the behavior of the extinction coefficient and the refractive index. An exponential decay of the refractive index ‘n’ as a function of wavelength was observed. The refractive index increases slightly when the pH increases to pH = 9.5 where it reaches its maximum. Beyond this value, it decreases sharply. This behavior has been …
Determination of elastoplastic properties of TiO2 thin films deposited on dual phase stainless steel using nanoindentation tests
2010
International audience; In recent years, the extraction of mechanical behaviour of thin films by nanoindentation using sharp indenter geometry has been extensively studied. This work investigates the mechanical properties of TiO2 thin film (1 µm thickness) deposited by spin coating on dual phase Duplex stainless steel and glass substrates. Experiments are carried out with different sharp triangular pyramids (a Cube corner and a Berkovich indenter) using a commercial Nano Indenter® XP apparatus. The substrate effect has been counteracted and an inverse method proposed in literature for bulk material has been adapted to assess the elastoplastic parameters of the tested thin film directly from…