Search results for "tensile"
showing 10 items of 453 documents
A family of weakest link models for fiber strength distribution
2007
It is well known that the most widely used distribution function for fiber tensile strength, the two-parameter Weibull distribution, does not always adequately describe the experimentally observed fiber strength scatter and the strength dependence on fiber length. To remedy this discrepancy, modifications of the Weibull distribution have been proposed that, while providing a good empirical fit to the strength data, sometimes lack the theoretical appeal of the weakest link models. We derive a family of weakest link models based on the assumption of a two-stage failure process incorporating explicitly the probabilities of flaw initiation and the fiber fracture due to the largest flaw (i.e. th…
KNOWN RESIDUAL STRESS SPECIMENS USING OPPOSED INDENTATION
2009
In order to test new theories for residual stress measurement or to test the effects of residual stress on fatigue, fracture, and stress corrosion cracking, a known stress test specimen was designed and then fabricated, modeled, and experimentally validated. To provide a unique biaxial stress state, a 60 mm diameter 10 mm thick disk of 316L stainless steel was plastically compressed through the thickness with an opposing 15 mm diameter hard steel indenters in the center of the disk. For validation, the stresses in the specimen were first mapped using time-of-flight neutron diffraction and Rietveld full pattern analysis. Next, the hoop stresses were mapped on a cross section of two disks usi…
Influence of correlations between stresses on calculated fatigue life of machine elements
1996
The correlation between components of the random stress tensor and its influence on the calculated fatigue life of machine elements were analysed. Three covariance matrices of components of biaxial stress state were considered. They were determined from measurements of strains in an element of a vibrating screen for aggregate, in the back wall of a bus, and in a welded element of excavator fittings. Calculations were made according to four criteria of multiaxial random fatigue. Cycles were counted with the rainflow method, and damage was cumulated with the Palmgren-Miner hypothesis. It was found that convariances of random stress state components strongly influence the calculated fatigue li…
A full body musculoskeletal model based on flexible multibody simulation approach utilised in bone strain analysis during human locomotion
2011
Load-induced strains applied to bone can stimulate its development and adaptation. In order to quantify the incident strains within the skeleton, in vivo implementation of strain gauges on the surfaces of bone is typically used. However, in vivo strain measurements require invasive methodology that is challenging and limited to certain regions of superficial bones only such as the anterior surface of the tibia. Based on our previous study [Al Nazer et al. (2008) J Biomech. 41:1036-1043], an alternative numerical approach to analyse in vivo strains based on the flexible multibody simulation approach was proposed. The purpose of this study was to extend the idea of using the flexible multibod…
Multi-objective optimization of nitinol stent design.
2017
Nitinol stents continuously experience loadings due to pulsatile pressure, thus a given stent design should possess an adequate fatigue strength and, at the same time, it should guarantee a sufficient vessel scaffolding. The present study proposes an optimization framework aiming at increasing the fatigue life reducing the maximum strut strain along the structure through a local modification of the strut profile.The adopted computational framework relies on nonlinear structural finite element analysis combined with a Multi Objective Genetic Algorithm, based on Kriging response surfaces. In particular, such an approach is used to investigate the design optimization of planar stent cell.The r…
Modeling of out-of-plane behavior of masonry walls
2009
The flexural behavior of rectangular masonry sections is investigated by considering nonlinear stress-strain in compression and limited-tension material. A preliminary analysis shows that, with variation in the parameters specializing with the adopted conventional constitutive law, the experimentally observed behavior of different kinds of masonry materials can be approximated. Subsequently, moment-curvature dimensionless curves are derived numerically by satisfying the equilibrium equations of the section. In the case of negligible tensile strength these curves exhibit a typical shape that can be approximated by analytical expressions; consequently, suitable functions are proposed that are…
Design and optimization of bonded patch repairs of laminated composite structures
2015
International audience; The present study proposes a method for design optimization of external patched repairs. The tensile behavior of notched specimens with patched repair was studied using finite element analysis and compared with experimental results. It was found that high stress concentrations along the transverse edges of circular patches and/or at the longitudinal edges of the hole leads to early damage initiation in the parent plate. The damage initiation site and its propagation depend on the patch in-plane stiffness. The optimal patch design can be characterized by a strength ratio R*. The overall design of the patch repair can be considered using a dimensionless design paramete…
The Transverse Crack Tension test revisited
2016
Several problems arise when measuring the mode II interlaminar fracture toughness using a Transverse Crack Tension specimen; in particular, the fracture toughness depends on the geometry of the specimen and cannot be considered a material parameter. A preliminary experimental campaign was conducted on TCTs of different sizes but no fracture toughness was measured because the TCTs failed in an unacceptable way, invalidating the tests. A comprehensive numerical and experimental investigation is conducted to identify the main causes of this behaviour and a modification of the geometry of the specimen is proposed. It is believed that the obtained results represent a significant contribution in …
Concrete softening effects on the axial capacity of RC jacketed circular columns
2016
Abstract Among the different strengthening techniques to repair RC structures, reinforced concrete (RC) jacketing is one of the most commonly adopted, especially for columns. Its wide application is due to its easy application and relatively reduced cost with respect to other methods (e.g. FRP wrapping, Shape Memory Alloy active confinement). The target of RC jacketing is to increase axial, flexural capacity and ductility of weak existing members by means of two main effects: confinement action provided by the jacket and composite action between external jacket and inner concrete. Different theoretical studies have been carried out to calculate the strength enhancement due to confinement ac…
Covariance between components of biaxial stress state in fatigue life calculations
1992
In this paper influence of correlalions between components of random stress tensor on the calculated fatigue life of the machine element has been analysed. Two groups of covariance matrices for components of biaxial stress state were considered. The first group was arbitrarily assumed and the second one was determined on the basis of the measured strains in the element of the vibrating screen for aggregate. Computer simulation was realized with four criteria of multiaxial random fatigue. Cycles were counted with the method of rain flow and damages were cumulated according to Palmgren-Miner hypothesis. It has been shown that covariances between components of stress state tensor strongly infl…