Search results for "testing."
showing 10 items of 1654 documents
Photo-acoustic phase-delayed excitation of guided waves in coated bone phantoms
2013
Photo-acoustic skeletal quantitative ultrasound enables assessment of the fundamental flexural guided wave (FFGW) propagating in bone. This mode, consistent with the F(1,1) tube mode can now be measured through a coating of soft tissue. Interference due to ultrasound propagation in the soft tissue surrounding the bone is reduced by using phase-delayed ultrasound excitation. Photo-acoustic phase-delayed excitation was done on five axisymmetric bone phantoms (1-5 mm wall thickness), coated by a 5 mm thick soft-tissue mimicking layer. A fiber head comprising a linear array of four optical fibers (400 μm diameter), illuminated by pulsed laser diodes (905 nm wavelength) generated ultrasound. Thi…
Ultrasonic Guided Wave Inspection of Bonded Lap Joints: Noncontact Method and Photoelastic Visualization
2001
The main topic of this paper is the nondestructive inspection of adhesively bonded lap joints by using ultrasonic guided (plate) waves. A noncontact, couplant-free method that employs capacitive air-coupled transducers is demonstrated for the inspection of thin aluminum joints with dimensions typical of aircraft fuselage and wing panels. Two types of bond defects, disbonded regions and regions of poorly cured (low-cohesive-strength) adhesive, are successfully detected by measuring the amplitude decrease of selected plate waves leaking from one adherend to the other one through the bondline. It is shown that proper choice of the vibrating mode structure, in terms of cross-sectional displacem…
Acoustically driven photon antibunching in nanowires.
2011
The oscillating piezoelectric field of a surface acoustic wave (SAW) is employed to transport photoexcited carriers, as well as to spatially control exciton recombination in GaAs-based nanowires (NWs) on a subns time scale. The experiments are carried out in core-shell NWs transferred to a SAW delay line on a LiNbO(3) crystal. Carriers generated in the NW by a focused laser spot are acoustically transferred to a second location, leading to the remote emission of subns light pulses synchronized with the SAW phase. The dynamics of the carrier transport, investigated using spatially and time-resolved photoluminescence, is well-reproduced by computer simulations. The high-frequency contactless …
Concentration depending fluorescence of 8-(di-(2-picolyl)) aminoBODIPY in solution
2014
[EN] An 8-dipicolylBODIPY derivative has been prepared and its photophysical properties evaluated under different conditions. Two different structures, hemicyanine and cyanine, are observed (depending on the solvent or the solution concentration). The hemicyanine form is not emissive whereas the cyanine form is fluorescent. This behavior is related with the planarity degree of the BODIPY core. The X-ray structure of the compound is reported and it shows that in solid state the hemicyanine form is present. The hemicyanine form seems to be stabilized by aggregation and is the main compound in concentrated solutions whereas the cyanine form is present in diluted solutions that are photochemica…
Quantitative subsurface defect detection in composite materials using a non-contact ultrasonic system
2002
The results of an experimental study conducted to detect subsurface defects in a thick Gr/PPS composite test sample using a noncontact ultrasonic system are presented. Surface waves are generated by a pulsed laser and detected by an air-coupled capacitance transducer. By controlling the surface wave wavelength through a shadow mask, it is possible to control surface wave penetration depth in the sample. Surface wave peak-to-peak amplitude is related to the near-surface material condition. Results indicate that signal amplitude decreases as the width of the defect increases and an approximately linear relation can be deduced.
Scaling and data collapse for the mean exit time of asset prices
2005
We study theoretical and empirical aspects of the mean exit time of financial time series. The theoretical modeling is done within the framework of continuous time random walk. We empirically verify that the mean exit time follows a quadratic scaling law and it has associated a pre-factor which is specific to the analyzed stock. We perform a series of statistical tests to determine which kind of correlation are responsible for this specificity. The main contribution is associated with the autocorrelation property of stock returns. We introduce and solve analytically both a two-state and a three-state Markov chain models. The analytical results obtained with the two-state Markov chain model …
Computational modeling of single-versus double-anchoring modes in di-branched organic sensitizers on TiO2 surfaces: structural and electronic propert…
2014
We present a first-principles DFT investigation of the adsorption geometry on the anatase (101) surface of a prototypical di-branched organic dye based on the extended tetrathiafulvalene moiety, incorporating two anchoring cyanoacrylic acid units. Reduced model systems with one and two anchoring groups have been initially studied to investigate the vibrational frequencies related to TiO2 dye adsorption. Our calculations confirm that the reduced systems can be used as reliable models to study the anchoring modes and that the conclusions extracted from the reduced systems can be extrapolated to the entire molecule. A series of molecular structures have been investigated to simulate the anchor…
Sensitivity on earth core and mantle densities using atmospheric neutrinos
2009
11 pages, 11 figures.-- ISI article identifier:000267776100008 .-- ArXiv pre-print avaible at: http://arxiv.org/abs/0904.0796
RGB Photoelasticity: Review and Improvements
2010
: This paper considers the main developments of RGB photoelasticity with reference to the maximum measurable retardation. In this paper, a new procedure based on the standard error function evaluated on a subset of the calibration array is also proposed and experimentally tested. The experiments show that the filament lamp makes it possible to find retardations until approximately 4 fringe orders while the fluorescent lamp makes it possible to determine higher fringe orders (12 fringe orders in this paper) owing to the discrete spectrum of the source. The paper shows that, by using the incandescent lamp, the primary limiting factor is the lack of modulation of the R, G and B signals wherea…
First data with the ATLAS Level-1 Calorimeter Trigger
2008
The ATLAS Level-1 Calorimeter Trigger is one of the main elements of the first stage of event selection for the ATLAS experiment at the LHC. The input stage consists of a mixed analogue/digital component taking trigger sums from the ATLAS calorimeters. The trigger logic is performed in a digital, pipelined system with several stages of processing, largely based on FPGAs, which perform programmable algorithms in parallel with a fixed latency to process about 300 Gbyte/s of input data. The real-time output consists of counts of different types of physics objects, and energy sums. The final system consists of over 300 custom-built VME modules, of several different types. The installation at AT…