Search results for "thermoplastic"
showing 10 items of 84 documents
Shear flow characterization of blends containing liquid crystal polymers
1992
A simple phenomenological approach is proposed in order to predict the presence of minima in the viscosity-composition curves of blends of thermoplastic with liquid crystal polymer (LCP). When the viscosity of the liquid crystal polymer is larger than that of the thermoplastic matrix, a minimum is observed. A possible explanation of the presence of yield stress in the flow curves of these blends is also given.
Gamma radiation of EVA-AA/MMA swollen systems to obtain mechanically improved blends
2002
In this work a "new" way to obtain "compatibilised" blends of rubber-glassy thermoplastic components is presented. Polyethylen-vinyl acetate acrylic acid terpolymer is swollen by methylmetacrylate and the system is irradiated through gamma rays in order to induce polymerisation of the monomer. Solubility and dynamic mechanical tests indicate the formation of a two phase system, even though in presence of strong interactions between the two components. Mechanical tensile behaviour is that of a ductile material with appreciable modulus values.
Thermal properties of e-beam cured epoxy/thermoplastic matrices for advanced composite materials
2007
The aim of this work is to investigate the possibility to improve the thermal behaviour of epoxy based systems, cured by ionizing radiation, in order to produce matrices for advanced carbon fibres composites. Blends of two epoxy monomers, difunctional and trifunctional, have been polymerized by e-beam irradiation and the dynamic mechanical thermal properties have been investigated. The increase of the concentration of the trifunctional epoxy monomer in the blend causes a marked increase of the Tg, but strongly decreases the reactivity. Subsequently, blends of the same epoxy monomers with a high Tg thermoplastic toughening agent have been considered and their reactivity and the thermal prope…
Processing and Mechanical Properties of Natural Fiber Reinforced Thermoplastic Starch Biocomposites
2007
Natural fiber reinforced starch polymers are processed by compression molding. Potato, sweet potato, and corn starch are used as matrices. Three types of natural fibers, namely sisal, jute, and cabuya, are used in concentrations varying from 2.5 to 12.5% w/w in the composites. Different plasticizers are used for the starch polymers, such as water and glycerol. Mechanical properties are assessed by tensile and impact tests. In both cases, improved mechanical properties are obtained at increasing fiber contents. Tensile strength appears to be markedly improved with the addition of 10% by weight of sisal fibers, while the best results for impact strength are obtained for cabuya fibers.
Mode I fracture toughness behavior of hydro-thermally aged carbon fibre reinforced DGEBA-HHPA-PES systems
2012
In this work the Mode I fracture toughness behavior of unidirectional CFRP laminates is investigated by means of Double Cantilever Beam (DCB) tests. The composite samples were manufactured by thermal curing after impregnation of a Carbon fabric with a DGEBA epoxy and anhydride HHPA curing agent. One resin batch was also mixed with a PES thermoplastic monomer to enhance the matrix toughness. Two lots of samples, toughened and un-toughened, were then left to soak in hot water to achieve various degrees of aging. The influence of matrix toughening and hydrothermal aging on the delamination behavior of the composite have then been assessed and correlated with characterization data from Dynamic …
Investigation on the indentation behavior of sandwich beams using crushable and hyperelastic foam cores
2010
In this work the indentation behaviour of sandwich beams is studied adopting the classical approach representing the core material as a Winkler-type foundation. It is shown how most of the proposed theories can be derived from a general fourth order linear differential equation expressing the equilibrium of the indented beam skin. Different assumptions on the supporting boundary constraints and materials constitutive behaviour, lead to simplifications of the general equation and to the prediction of different indentation features. An extension of the Segment-Wise approach recently proposed in the literature is in particular presented with potential to better simulate foam cores with markedl…
Mechanical properties of injection-molded binary blends of polyethylene with small additions of a liquid-crystalline polymer
2011
The results of the investigation of the mechanical properties of polyethylene (PE) blends with small (<3 wt %) additions of thermotropic liquid-crystalline polymers (LCPs) are reported. PE/LCP compositions with various LCP weight contents were obtained by thermoplastic mixing in a two-stage process. Short-term and long-term mechanical behavior of various PE/LCP compositions were analyzed. Data on the influence of LCP addition on the tensile elastic modulus [or Young's modulus (E)], stress at yield (σY), stress at break (σB), strain at yield, strain at break, and deformation at long-term (1000-h) tensile creep were obtained. The experimental results of the investigation show that even small …
Enhanced polyurethanes based on different polycarbonatediols
2012
Segmented thermoplastic polyurethanes (PUs) were prepared from 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butanediol (BD) and different macrodiols with a molar mass of 1000. Properties of those PUs based on polycarbonatediol (PCD) were compared with their homologous based on polyesterdiol and polyetherdiol as macrodiols. The proportion used in this study was macrodiol:BD:MDI = 1:2:3, in mole ratio. The hard segment weight percentage is 48 wt% for different PUs. Thermogravimetric analysis, differential scanning calorimetry, differential mechanical analysis, Fourier transform infrared-attenuated total reflection spectroscopy, as well as mechanical properties and retention on flexural prope…
Thermal Analysis, Mechanical and Rheological Behaviour of Melt Manufactured Polyethylene/Liquid Crystal Polymer Blends
2011
Modification of properties of conventional thermoplastics with thermotropic liquid crystal polymers, from one hand, allows decrease their viscosities, substantially facilitating processing conditions, and, from another hand, allows increase their exploitation properties. Orientation of the labile structure of liquid crystal polymer in extrusion or injection moulding causes specific reinforcement (so-called self-reinforcement) to occur in the blends containing liquid crystal polymer. Up to now the effect of self-reinforcement is mostly investigated in the blends, containing considerable amount of liquid crystal polymer. In this research the effect of minor amounts of liquid crystalline co-po…
Acrylic Graft Copolymers Via Macromonomers
1995
Comb-shaped poly(methyl methacrylate) (PMMA) and PMMA grafted with poly(nbutyl acrylate) (PnBuA) were prepared by radical copolymerisation of ω-methacryloyl-PMMA with MMA and nBuA, respectively. The comb-shaped PMMA is characterised with respect to radius of gyration by using GPC equipped with a multi-angle laser light scattering detector. The radical copolymerisation of the macromonomer with nBuA in toluene follows complex kinetics. The dependence of the relative reactivity of the macromonomer on absolute concentration and on the ratio of comonomers may be explained by preferential solvation of comonomers by segments of their own kind (“bootstrap effect”) or even micelle formation. However…