Search results for "titanium oxide"

Development of the microwave transduction applied to ammonia detection : from nanomaterials to broadband sensor, understanding of the mechanisms and …

2017

The main objective of this thesis is to propose an analysis of the microwave transduction specificities in the framework of ammonia sensing applications. The two main features of this transduction are its broadband characterization (1 to 8 GHz) as well as its sensitive materials (dielectrics). This transduction method is based on the interaction between a polluting gas and a sensitive material deposited on the surface of a microwave-specific propagating structure. The response of the sensor is not directly induced by the dielectric properties of the gaseous target molecule, but rather by those of the target species adsorbed on the surface of the sensitive material. This adsorption causes a …

Red Shift in the Light Absorption Threshold of Anodic TiO2 Films Induced by Nitrogen Incorporation

2014

Abstract Titanium foils were anodized in ammonium containing and ammonium free solutions in order to check the possibility of inducing nitrogen incorporation into anodic TiO 2 films. XPS spectra confirmed the presence of O-Ti-N bonds on the surface of the anodic films prepared in ammonium biborate electrolytes. In order to evidence the effect of nitrogen incorporation on the light absorption threshold, photoelectrochemical behavior of as-anodized and high temperature annealed films as a function of the anodizing electrolyte composition were investigated. A photocurrent tail at energies lower than the mobility gap of TiO 2 appeared for those films prepared in ammonium containing electrolytes…

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

2009

Titania-modified silicas with different weight% of TiO2 were prepared by sol-gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO2. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO2 improved the catalytic activity, with an optimum of the performance for 10 wt% TiO2 loading. Moreover, the titaniacontaining catalysts exhibited a superior tolerance towards SO2 by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 8C. Catalysts were characterize…

A Thermo-Kinetic Study of Titanium Oxidation Assisted by a Nd-YAG Pulsed Laser

2004

Scanning tunneling microscopy and spectroscopy of Mo clusters grown on TiO2(110).

2007

Molybdenum was deposited in two steps (3 eq. ML and 1 eq. ML) on the light blue rutile TiO2 10) (1 x 1) surface at room temperature, each Mo deposition cycle being followed by an annealing up to 950-1000 K. This procedure was found to lead to formation of separated clusters having a size in very wide range (1-20 nm). Scanning tunneling microscopy showed a dependence of the cluster morphology as a function of the size. The scanning tunneling spectra of Mo clusters was studied as a function of cluster dimensions and discussed in comparison with photoelectron spectroscopy results previously obtained for homogeneous Mo films. The dI/d V curves do not display the valence band structure of deposi…

Field-induced tip–sample oxygen transfer in scanning tunneling microscopy on TiO2(110) (1 1).

2008

International audience; A study on the field-induced tip–surface oxygen transfer at room temperature and its influence on the tunneling conditions for stable STM imaging of the TiO2(110) (1 1) surface is reported. A simple model of field-induced transfer is applied to tungsten and platinum–iridium tips. The oxygen transition rates from the sample to the tip or from the tip to the sample depend on the oxygen desorption barriers formed at tunneling distance. For stable imaging the applied bias voltage has to balance the oxygen transfer probabilities in both directions. In the case of Pt/Ir tips, the tunneling conditions for images with clear evidence of bridging oxygen point defects have been…

Porous titania surfaces on titanium with hierarchical macro- and mesoporosities for enhancing cell adhesion, proliferation and mineralization

2014

Titanium received a macroporous titania surface layer by anodization, which contains open pores with average pore diameter around 5 μm. An additional mesoporous titania top layer following the contour of the macropores, of 100-200 nm thickness and with a pore diameter of 10nm, was formed by using the evaporation-induced self-assembly (EISA) method with titanium (IV) tetraethoxide as the precursor. A coherent laminar titania surface layer was thus obtained, creating a hierarchical macro- and mesoporous surface that was characterized by high-resolution electron microscopy. The interfacial bonding between the surface layers and the titanium matrix was characterized by the scratch test that con…

Sensitizer exchange dynamics in air and solvent filled semiconductor nanocavities

2010

Multiple dye binding sites and their exchange in equilibrium in air and solvent filled sensitized titanium oxide nanocavities were identified by 2DIR spectroscopy. Binding geometry and flexibility may influence electron injection efficiency of solar cells.

Graphene Field-Effect Transistors Employing Different Thin Oxide Films: A Comparative Study

2019

In this work, we report on a comparison among graphene field-effect transistors (GFETs) employing different dielectrics as gate layers to evaluate their microwave response. In particular, aluminum oxide (Al$_{2}$O$_{3}$), titanium oxide (TiO$_{2}$), and hafnium oxide (HfO$_{2}$) have been tested. GFETs have been fabricated on a single chip and a statistical analysis has been performed on a set of 24 devices for each type of oxide. Direct current and microwave measurements have been carried out on such GFETs and short circuit current gain and maximum available gain have been chosen as quality factors to evaluate their microwave performance. Our results show that all of the devices belonging …

Pyrolysis study of sol-gel derived TiO2powders

2004

An amorphous TiO2 gel was obtained by hydrolysing titanium(IV) isopropoxide with a stoichiometric amount of water using SnCl2 as catalyst. In these operative conditions, a TiO2 gel matrix containing a lower fraction of organic residual was obtained with respect to samples prepared by previously modifying the titanium alkoxide precursor with chelating ligands. Dried gel powders were characterized by N2 adsorption analyses, FT-IR and XRD measurements. Thermogravimetric (TG) and differential thermal analysis (DTA) coupled with mass spectrometric (MS) and gas chromatographic (GC) measurements were performed in order to identify the organic products released from TiO2 gel pyrolysis. The Tg-MS se…