Search results for "umidi"
showing 10 items of 324 documents
From the solution processing of hydrophilic molecules to polymer-phthalocyanine hybrid materials for ammonia sensing in high humidity atmospheres.
2014
We have prepared different hybrid polymer-phthalocyanine materials by solution processing, starting from two sulfonated phthalocyanines, s-CoPc and CuTsPc, and polyvinylpyrrolidone (PVP), polyethylene glycol (PEG), poly(acrylic acid-co-acrylamide) (PAA-AM), poly(diallyldimethylammonium chloride) (PDDA) and polyaniline (PANI) as polymers. We also studied the response to ammonia (NH3) of resistors prepared from these sensing materials. The solvent casted films, prepared from s-CoPc and PVP, PEG and PAA-AM, were highly insulating and very sensitive to the relative humidity (RH) variation. The incorporation of s-CoPc in PDDA by means of layer-by-layer (LBL) technique allowed to stabilize the fi…
A methodology to assess the effect of sweat on infrared thermography data after running: Preliminary study
2020
Abstract The aim of this technical report is to present a preliminary study carried out to define the methodology to be employed for further research on assessing the effect of sweating on infrared thermography and thermal contact sensors after moderate intensity running. Nine recreational runners participated in this preliminary study. Participants ran for 35 min (5 min warm-up and 30 min at a rate of perceived exertion rate of 12 points on the 6–20 points Borg scale). Skin temperature (infrared thermography, Flir E60bx; four thermal contact sensors, IButton DS1923 Hygrochron) and relative humidity (thermal contact sensors) were measured on the anterior thigh on both lower limbs before and…
Improved stability of black silicon detectors using aluminum oxide surface passivation
2021
Publisher Copyright: © 2021 ESA and CNES We have studied how high-energy electron irradiation (12 MeV, total dose 66 krad(Si)) and long term humidity exposure (75%, 75 °C, 500 hours) influence the induced junction black silicon or planar photodiode characteristics. In our case, the induced junction is formed using n-type silicon and atomic-layer deposited aluminum oxide (Al2O3), which contains a large negative fixed charge. We compare the results with corresponding planar pn-junction detectors passivated with either with silicon dioxide (SiO2) or Al2O3. The results show that the induced junction detectors remain stable as their responsivity remains nearly unaffected during the electron beam…
Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester
2021
This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that th…
Cyclic moisture sorption and its effects on the thermomechanical properties of epoxy and epoxy/MWCNT nanocomposite
2019
The aim of this work was to reveal the moisture absorption&ndash
Low Conductive Electrodeposited Poly(2,5-dimethoxyaniline) as a Key Material in a Double Lateral Heterojunction, for Sub-ppm Ammonia Sensing in Humid…
2019
We present a new device called a double lateral heterojunction (DLH) as an ammonia sensor in humid atmosphere. It combines polyaniline derivatives in their poor conducting state with a highly conductive molecular material, lutetium bisphthalocyanine, LuPc2. Polyaniline and poly(2,5-dimethoxyaniline) are electrodeposited on ITO interdigitated electrodes, leading to an original device that can be obtained only by electrochemistry and not by other solution processing techniques. Both polymers lead to highly conducting materials that require a neutralization step before their coverage by LuPc2. While the device based on polyaniline shows ohmic behavior, the nonlinear I- V characteristics of the…
Humidity effects on gravitational settling and Brownian diffusion of atmospheric aerosol particles
1977
The dependency on relative humidity of the settling velocity of aerosol particles in stagnant air and of the diffusion coefficient due to Brownian motion of aerosol particles was computed for six aerosol types and different particles sizes in dry state. The computations are based (1) on mean bulk densities of dry aerosol particles obtained from measurements or from the knowledge of the chemical composition of the particles, (2) on micro-balance measurements of the water uptake per unit mass of dry aerosol substance versus water activity at thermodynamic equilibrium, and (3) on measurements of the equilibrium water activity of aqueous sea salt solutions. The results show a significant depend…
Environmental chamber for an atomic force microscope.
2007
A commercial atomic force microscope (AFM), originally designed for operation in ambient conditions, was placed inside a compact aluminum chamber, which can be pumped down to high vacuum levels or filled with a desired gaseous atmosphere, including humidity, up to normal pressure. The design of this environmental AFM is such that minimal intrusion is made to the original setup, which can be restored easily. The performance inside the environmental chamber is similar to the original version.
Molecular Semiconductors — Doped Insulator (MSDI) heterojunctions as new conductometric devices for chemosensing in wet atmosphere.
2015
Most of the gas sensors are based on resistors with inorganic materials and more rarely on other conductometric devices (diodes or transistors). Conductometric sensors have also been designed with molecular materials. Thus, in 2009, Molecular Semiconductor — Doped-insulator (MSDI) heterojunctions were built around a heterojunction between a molecular semiconductor (MS) and a doped-insulator (DI). The MS must be more conductive than the sublayer to take advantage of the heterojunction. The MS is generally of p-type and DI can be of p-type (p-MSDI) or n-type (n-MSDI) material. The energy barrier at the interface depends on the difference in the charge carrier density in the two layers, leadin…
The Influence of Ageing on the Impact Damage of Carbon Epoxy Composites
2011
Abstract This study looks into the influence of ageing on the carbon epoxy composite when impact is applied. Three different stacking sequences were investigated, one sequence with the classic lay-up, whereas the other two have quasi-isotropic and quasi-homogeneous behaviour. The specimens were aged up to 2100 h (3 months) in a climatic chamber with a temperature of 70 °C and relative humidity of 85%. The mass was measured regularly during the hygrothermal ageing treatment. The mass was always measured directly after exiting the climatic chamber and it was noted that for each stacking sequence, the same regular increase in mass is observed until stabilisation. The specimens were then impact…