0000000000089571
AUTHOR
Maarit Karppinen
Influence of titanium-substrate roughness on Ca–P–O thin films grown by atomic layer deposition
Abstract Amorphous Ca–P–O films were deposited on titanium substrates using atomic layer deposition, while maintaining a uniform Ca/P pulsing ratio of 6/1 with varying number of atomic layer deposition cycles starting from 10 up to 208. Prior to film deposition the titanium substrates were mechanically abraded using SiC abrasive paper of 600, 1200, 2000 grit size and polished with 3 μm diamond paste to obtain surface roughness R rms values of 0.31 μm, 0.26 μm, 0.16 μm, and 0.10 μm, respectively. The composition and film thickness of as-deposited amorphous films were studied using Time-Of-Flight Elastic Recoil Detection Analysis. The results showed that uniform films could be deposited on ro…
Low-temperature atomic layer deposition of ZnO thin films: Control of crystallinity and orientation
Abstract Low-temperature atomic layer deposition (ALD) processes are intensely looked for to extend the usability of the technique to applications where sensitive substrates such as polymers or biological materials need to be coated by high-quality thin films. A preferred film orientation, on the other hand, is often required to enhance the desired film properties. Here we demonstrate that smooth, crystalline ZnO thin films can be deposited from diethylzinc and water by ALD even at room temperature. The depositions were carried out on Si(100) substrates in the temperature range from 23 to 140 °C. Highly c-axis-oriented films were realized at temperatures below ~ 80 °C. The film crystallinit…
Low-temperature molecular layer deposition using monifunctional aromatic precursors and ozone-based ring-opening reactions
Molecular layer deposition (MLD) is an increasingly used deposition technique for producing thin coatings consisting of purely organic or hybrid inorganic-organic materials. When organic materials are prepared, low deposition temperatures are often required to avoid decomposition, thus causing problems with low vapor pressure precursors. Monofunctional compounds have higher vapor pressures than traditional bi- or trifunctional MLD precursors, but do not offer the required functional groups for continuing the MLD growth in subsequent deposition cycles. In this study, we have used high vapor pressure monofunctional aromatic precursors in combination with ozone-triggered ring-opening reactions…
Cellulose-inorganic hybrids of strongly reduced thermal conductivity
Abstract The employment of atomic layer deposition and spin coating techniques for preparing inorganic-organic hybrid multilayer structures of alternating ZnO-CNC layers was explored in this study. Helium ion microscopy and X-ray reflectivity showed the superlattice formation for the nanolaminate structures and atomic force microscopy established the efficient control of the CNCs surface coverage on the Al-doped ΖnO by manipulating the concentration of the spin coating solution. Thickness characterization of the hybrid structures was performed via both ellipsometry and X-ray reflectivity and the thermal conductivity was examined by time domain thermoreflectance technique. It appears that ev…
Area‐Selective Atomic Layer Deposition on Functionalized Graphene Prepared by Reversible Laser Oxidation
Publisher Copyright: © 2022 The Authors. Advanced Materials Interfaces published by Wiley-VCH GmbH. Area-selective atomic layer deposition (ALD) is a promising “bottom-up” alternative to current nanopatterning techniques. While it has been successfully implemented in traditional microelectronic processes, selective nucleation of ALD on 2D materials has so far remained an unsolved challenge. In this article, a precise control of the selective deposition of ZnO on graphene at low temperatures (<250 °C) is demonstrated. Maskless femtosecond laser writing is used to locally activate predefined surface areas (down to 300 nm) by functionalizing graphene to achieve excellent ALD selectivity (up to…
Antibacterial and barrier properties of oriented polymer films with ZnO thin films applied with atomic layer deposition at low temperatures
Abstract Concerns on food safety, and need for high quality and extended shelf-life of packaged foods have promoted the development of antibacterial barrier packaging materials. Few articles have been available dealing with the barrier or antimicrobial properties of zinc oxide thin films deposited at low temperature with atomic layer deposition (ALD) onto commercial polymer films typically used for packaging purposes. The purpose of this paper was to study the properties of ZnO thin films compared to those of aluminum oxide. It was also possible to deposit ZnO thin films onto oriented polylactic acid and polypropylene films at relatively low temperatures using ozone instead of water as an o…
Atomic Layer Deposition of Intermetallic Fe4Zn9 Thin Films from Diethyl Zinc
| openaire: EC/H2020/765378/EU//HYCOAT We present a new type of atomic layer deposition (ALD) process for intermetallic thin films, where diethyl zinc (DEZ) serves as a coreactant. In our proof-of-concept study, FeCl3 is used as the second precursor. The FeCl3 + DEZ process yields in situ crystalline Fe4Zn9 thin films, where the elemental purity and Fe/Zn ratio are confirmed by time-of-flight elastic recoil detection analysis (TOF-ERDA), Rutherford backscattering spectrometry (RBS), atomic absorption spectroscopy (AAS), and energy-dispersive X-ray spectroscopy (EDX) analyses. The film thickness is precisely controlled by the number of precursor supply cycles, as expected for an ALD process.…
Atomic layer deposition of WO3 thin films using W(CO)6 and O3 precursors
Here we report a new atomic layer deposition (ALD) process for WO3 thin films based on W(CO)6 as a tungsten source and ozone as a source of oxygen. A narrow ALD temperature window is found at 195–205 °C for WO3 with a deposition rate of 0.23 A per cycle. As-deposited films are partially crystalline with root mean square (rms) roughness values of 4.7 nm for 90 nm thick films; annealing the films at 600–1000 °C under oxygen or nitrogen atmospheres enhances the degree of crystallinity considerably. Our results show that the straightforward ALD chemistry of carbonyl compounds and ozone is applicable to the deposition of WO3 thin films.
Low-temperature Molecular Layer Deposition Using Monofunctional Aromatic Precursors and Ozone-based Ring Opening Reactions
Molecular layer deposition (MLD) is an increasingly used deposition technique for producing thin coatings consisting of purely organic or hybrid inorganic–organic materials. When organic materials are prepared, low deposition temperatures are often required to avoid decomposition, thus causing problems with low vapor pressure precursors. Monofunctional compounds have higher vapor pressures than traditional bi- or trifunctional MLD precursors, but do not offer the required functional groups for continuing the MLD growth in subsequent deposition cycles. In this study, we have used high vapor pressure monofunctional aromatic precursors in combination with ozone-triggered ring-opening reactions…
Control of Oxygen Nonstoichiometry and Magnetic Property of MnCo2O4 Thin Films Grown by Atomic Layer Deposition
Spinel-structured (Mn,Co)3O4 thin films were reproducibly fabricated by atomic layer deposition (ALD) using Mn(thd)3, Co(thd)2, and ozone as precursors. A full control of the cation ratio was achieved in the temperature interval 140−160 °C within which also the growth rate remained constant. Precise control of the oxygen content of as-deposited MnCo2O4+δ films was achieved through postdeposition heat treatments at prefixed temperatures in air and N2 atmospheres, as evidenced from the monotonous increases of both the unit cell volume and the Curie temperature (TC) with increasing annealing temperature/decreasing oxygen partial pressure. The TC value varied from 92 K for the as-deposited MnCo…