CaP-Bioglass composite coating by galvanic deposition

Orthopedic devices are increasingly used in our life to improve the health of patients after bone fractures due to accidents, aging, or sports injuries. Metallic materials (i.e. stainless steel, titanium alloys chromium alloys) are widely employed to fabricate prostheses, screws, and osteosynthesis plates. Although metals could be good mechanical properties like human bone, corrosion phenomena could occur, causing in the worst cases the failure of orthopedic implants. In addition, metal ions released around periprosthetic tissues could arise allergenic and cancerogenic effects. Nowadays, the research was focused on coating science to deal with these issues. In particular, the development of…

Pd-Co-Based Electrodes for Hydrogen Production by Water Splitting in Acidic Media

To realize the benefits of a hydrogen economy, hydrogen must be produced cleanly, efficiently and affordably from renewable resources and, preferentially, close to the end-users. The goal is a sustainable cycle of hydrogen production and use: in the first stage of the cycle, hydrogen is produced from renewable resources and then used to feed a fuel cell. This cycle produces no pollution and no greenhouse gases. In this context, the development of electrolyzers producing high-purity hydrogen with a high efficiency and low cost is of great importance. Electrode materials play a fundamental role in influencing electrolyzer performances; consequently, in recent years considerable efforts have b…

Galvanic Deposition of Hydroxyapatite/Chitosan/Collagen Coatings on 304 Stainless Steel

The galvanic deposition method was used to deposit Hydroxyapatite/Chitosan/Collagen coatings on 304 stainless steel. Galvanic deposition is an alternative and valid way to fabricate bio-coatings with high biocompatibility and good anticorrosion properties. Physical-chemical characterizations were carried out to investigate chemical composition and morphology of the samples. Coatings consist of a mixture of calcium phosphate (Brushite and Hydroxyapatite) with chitosan and collagen. Corrosion tests were performed in the simulated body fluid (SBF) after different aging times. Results show that, in comparison with bare 304 stainless steel, coating shifts corrosion potential to anodic values and…

Galvanic deposition of Chitosan-AgNPs as antibacterial coating

Thanks to mechanical properties similar human bones, metallic materials represent the best choice for fabrication of orthopedic implants. Although metals could be widely used in the field of biomedical implants, corrosion phenomena could occur, causing metal ions releasing around periprosthetic tissues leading, in the worst cases, to the development of infections. In these cases, patients need prolonged antibiotic therapies that may cause bacterial resistance. Preventing bacterial colonization of biomedical surfaces is the key to limiting the spread of infections. Antibacterial coatings have become a very active field of research, strongly stimulated by the increasing urgency of identifying…

Effect of Polyhydroxyalkanoate (PHA) Concentration on Polymeric Scaffolds Based on Blends of Poly-L-Lactic Acid (PLLA) and PHA Prepared via Thermally Induced Phase Separation (TIPS)

Hybrid porous scaffolds composed of both natural and synthetic biopolymers have demonstrated significant improvements in the tissue engineering field. This study investigates for the first time the fabrication route and characterization of poly-L-lactic acid scaffolds blended with polyhydroxyalkanoate up to 30 wt%. The hybrid scaffolds were prepared by a thermally induced phase separation method starting from ternary solutions. The microstructure of the hybrid porous structures was analyzed by scanning electron microscopy and related to the blend composition. The porosity and the wettability of the scaffolds were evaluated through gravimetric and water contact angle measurements, respective…

Deposition and characterization of coatings of Hydroxyapatite, Chitosan, and Hydroxyapatite-Chitosan on 316L for biomedical devices

In the last decades, the scientific community has turned on great interest towards the development of increasingly performing biomedical systems. In the orthopedic field, biomedical devices are made up by metallic materials (mainly steel and titanium alloys), which have low/medium resistance to corrosion and a low osteointegration capacity when implanted inside the human body. This can lead to infection or inflammation that can damage the tissues surrounding the implant. The use of biocompatible coatings allows cancelling or mitigating these phenomena. The coating interposing between aggressive environment and biomedical device inhibits corrosion so limiting the metal ions release into the …

Behavior of Calcium Phosphate–Chitosan–Collagen Composite Coating on AISI 304 for Orthopedic Applications

Calcium phosphate/chitosan/collagen composite coating on AISI 304 stainless steel was investigated. Coatings were realized by galvanic coupling that occurs without an external power supply because it begins with the coupling between two metals with different standard electrochemical potentials. The process consists of the co-deposition of the three components with the calcium phosphate crystals incorporated into the polymeric composite of chitosan and collagen. Physical-chemical characterizations of the samples were executed to evaluate morphology and chemical composition. Morphological analyses have shown that the surface of the stainless steel is covered by the deposit, which has a very r…

Coating su substrati metallici per applicazioni in campo ortopedico

Nanostructured Lead Electrodes with Reduced Graphene Oxide for High-Performance Lead–Acid Batteries

Nanostructured Pb electrodes consisting of nanowire arrays were obtained by electrodeposition, to be used as negative electrodes for lead–acid batteries. Reduced graphene oxide was added to improve their performances. This was achieved via the electrochemical reduction of graphene oxide directly on the surface of nanowire arrays. The electrodes with and without reduced graphene oxide were tested in a 5 M sulfuric acid solution using a commercial pasted positive plate and an absorbed glass mat separator in a zero-gap configuration. The electrodes were tested in deep cycling conditions with a very low cut-off potential. Charge–discharge tests were performed at 5C. The electrode wi…

Electrochemical Quantification of H2O2 Released by Airway Cells Growing in Different Culture Media

Quantification of oxidative stress is a challenging task that can help in monitoring chronic inflammatory respiratory airway diseases. Different studies can be found in the literature regarding the development of electrochemical sensors for H2O2 in cell culture medium to quantify oxidative stress. However, there are very limited data regarding the impact of the cell culture medium on the electrochemical quantification of H2O2. In this work, we studied the effect of different media (RPMI, MEM, DMEM, Ham’s F12 and BEGM/DMEM) on the electrochemical quantification of H2O2. The used electrode is based on reduced graphene oxide (rGO) and gold nanoparticles (AuNPs) and was obtained by co-electrode…

Simultaneous detection of copper and mercury in water samples using in-situ pH control with electrochemical stripping techniques

The performance of electrochemical sensors using an in situ pH control technique for detection of mercury and copper in neutral solutions is described herein. Sensors are comprised of two distinct parallel gold interdigitated microband electrodes each of which may be polarised separately. Biasing one interdigitated “protonator” electrode sufficiently positive to begin water electrolysis, resulted in the production of H+ ions, which, consequently droped the interfacial pH at the other second interdigitated “sensing” electrode. This decrease in pH permitted the electrodeposition (and consequent stripping) of metals at a sensing electrode without the need to acidify the whole test solution. In…

Galvanic Deposition of Calcium Phosphate/Bioglass Composite Coating on AISI 316L

Calcium phosphate/Bioglass composite coatings on AISI 316L were investigated with regard to their potential role as a beneficial coating for orthopedic implants. These coatings were realized by the galvanic co-deposition of calcium phosphate compounds and Bioglass particles. A different amount of Bioglass 45S5 was used to study its effect on the performance of the composite coatings. The morphology and chemical composition of the coatings were investigated before and after their aging in simulated body fluid. The coatings uniformly covered the AISI 316L substrate and consisted of a brushite and hydroxyapatite mixture. Both phases were detected using X-ray diffraction and Raman spectroscopy.…

Green and Integrated Wearable Electrochemical Sensor for Chloride Detection in Sweat

Wearable sensors for sweat biomarkers can provide facile analyte capability and monitoring for several diseases. In this work, a green wearable sensor for sweat absorption and chloride sensing is presented. In order to produce a sustainable device, polylactic acid (PLA) was used for both the substrate and the sweat absorption pad fabrication. The sensor material for chloride detection consisted of silver-based reference, working, and counter electrodes obtained from upcycled compact discs. The PLA substrates were prepared by thermal bonding of PLA sheets obtained via a flat die extruder, prototyped in single functional layers via CO2 laser cutting, and bonded via hot-press. The effect of co…

Deposition and characterization of Hydroxyapatite-Chitosan coatings on 304 SS for biomedical devices

During the last years biomaterials have been largely investigated in order to perform and improve biomedical devices. As regards orthopedic field, the most common equipment used (such as implants, bone grafts or screws) are constituted by metallic materials (steel and titanium alloys), characterized by low/medium resistance to corrosion and low osteointegration ability. Furthermore, these factors could produce local inflammations of the tissues surrounding the implants, increasing kinetics of corrosion phenomena. Scientific community has focused the attention on biocoatings interposed between metal and aggressive environment in order to inhibit corrosion. Furthermore, these coatings are abl…