0000000000286775
AUTHOR
M. Bellato
showing 11 related works from this author
Response of AGATA segmented HPGe detectors to gamma rays up to 15.1MeV
2013
WOS: 000314826000009
Feasibility and physics potential of detecting $^8$B solar neutrinos at JUNO
2021
The Jiangmen Underground Neutrino Observatory (JUNO) features a 20 kt multi-purpose underground liquid scintillator sphere as its main detector. Some of JUNO's features make it an excellent location for 8B solar neutrino measurements, such as its low-energy threshold, high energy resolution compared with water Cherenkov detectors, and much larger target mass compared with previous liquid scintillator detectors. In this paper, we present a comprehensive assessment of JUNO's potential for detecting 8B solar neutrinos via the neutrino-electron elastic scattering process. A reduced 2 MeV threshold for the recoil electron energy is found to be achievable, assuming that the intrinsic radioactive …
Optimization of the JUNO liquid scintillator composition using a Daya Bay antineutrino detector
2021
To maximize the light yield of the liquid scintillator (LS) for the Jiangmen Underground Neutrino Observatory (JUNO), a 20 t LS sample was produced in a pilot plant at Daya Bay. The optical properties of the new LS in various compositions were studied by replacing the gadolinium-loaded LS in one antineutrino detector. The concentrations of the fluor, PPO, and the wavelength shifter, bis-MSB, were increased in 12 steps from 0.5 g/L and <0.01 mg/L to 4 g/L and 13 mg/L, respectively. The numbers of total detected photoelectrons suggest that, with the optically purified solvent, the bis-MSB concentration does not need to be more than 4 mg/L. To bridge the one order of magnitude in the detect…
Conceptual design and infrastructure for the installation of the first AGATA sub-array at LNL
2011
WOS: 000295765100014
Multiple register synchronization with a high-speed serial link using the Aurora protocol
2013
In this work, the development and characterization of a multiple synchronous registers interface communicating with a high-speed serial link and using the Aurora protocol is presented. A detailed description of the developing process and the characterization methods and hardware test benches are also included. This interface will implement the slow control busses of the digitizer cards for the second generation of electronics for the Advanced GAmma Tracking Array (AGATA).
Performance of the Fully Digital FPGA-Based Front-End Electronics for the GALILEO Array
2014
In this work we present the architecture and results of a fully digital Front End Electronics (FEE) read out system developed for the GALILEO array. The FEE system, developed in collaboration with the Advanced Gamma Tracking Array (AGATA) collaboration, is composed of three main blocks: preamplifiers, digitizers and preprocessing electronics. The slow control system contains a custom Linux driver, a dynamic library and a server implementing network services. The digital processing of the data from the GALILEO germanium detectors has demonstrated the capability to achieve an energy resolution of 1.53 per mil at an energy of 1.33 MeV.
Conceptual design of the AGATA 1$\pi$ array at GANIL
2017
The Advanced GAmma Tracking Array (AGATA) has been installed at the GANIL facility, Caen-France. This setup exploits the stable and radioactive heavy-ions beams delivered by the cyclotron accelerator complex of GANIL. Additionally, it benefits from a large palette of ancillary detectors and spectrometers to address in-beam γ-ray spectroscopy of exotic nuclei. The set-up has been designed to couple AGATA with a magnetic spectrometer, charged-particle and neutron detectors, scintillators for the detection of high-energy γ rays and other devices such as a plunger to measure nuclear lifetimes. In this paper, the design and the mechanical characteristics of the set-up are described. Based on sim…
A PCI Express optical link based on low-cost transceivers qualified for radiation hardness
2013
In this paper we want to demonstrate that an optical physical medium is compatible with the second generation of PCI Express. The benefit introduced by the optical decoupling of a PCI Express endpoint is twofold: it allows for a geographical detachment of the device and it remains compliant with the usual PCI accesses to the legacy I/O and memory spaces. We propose two boards that can bridge the PCI Express protocol over optical fiber. The first is a simple optical translator while the second is a more robust switch developed for connecting up to four devices to a single host. Such adapters are already working in the control and data acquisition system of a particle detector at CERN and hen…
Graphical user interface for serial protocols through a USB link
2012
In this work, a graphical user interface to communicate with three common serial protocols is presented. With one tool, the user may be able to control several evaluation boards from different manufacturers or evaluate and program integrated circuits of complex board prototypes. It provides a user-friendly interface to communicate with several chips using the USB port. The program has been used for the first stages in the qualification process of electronic boards for the Advanced GAmma Tracking Array (AGATA).
Development of the control card for the digitizers of the second generation electronics of AGATA
2012
In this work, the features and development process of the novel control card for the digitizers of AGATA are presented. The board is part of the new hardware proposed for the electronic system of the experiment. In particular, the control card provides the sampling clock for the digitizers, contributes to the synchronization of the digital data and performs the slow control of its associated digitizer cards.
Distillation and stripping pilot plants for the JUNO neutrino detector: Design, operations and reliability
2019
Abstract This paper describes the design, construction principles and operations of the distillation and stripping pilot plants tested at the Daya Bay Neutrino Laboratory, with the perspective to adapt these processes, system cleanliness and leak-tightness standards to the final full scale plants to be used for the purification of the liquid scintillator of the JUNO neutrino detector. The main goal of these plants is to remove radio impurities from the liquid scintillator while increasing its optical attenuation length. Purification of liquid scintillator will be performed with a system combining alumina oxide, distillation, water extraction and steam (or N 2 gas) stripping. Such a combined…