0000000000811440
AUTHOR
C. Solans
Installation and commissioning of the TileCal Read-Out Drivers
TileCal is the hadronic tile calorimeter of the ATLAS experiment at LHC/CERN. The main component of the TileCal back-end electronics is the Read-Out Driver (ROD). The ROD system is placed between the first and the second level trigger and it is the responsible for processing the data gathered by the detector. The principal devices of the RODs are the Digital Signal Processors (DSPs) mounted in the Processing Units (PUs) daughterboards. The architecture and functionality of the RODs are briefly explained. Then, it is presented the ROD system installation in the ATLAS electronics cavern. Currently, the RODs are being used for the detector commissioning. It is detailed the Detector and Verific…
ATLAS TileCal Read Out Driver production
The production tests of the 38 ATLAS TileCal Read Out Drivers (RODs) are presented in this paper. The hardware specifications and firmware functionality of the RODs modules, the test-bench and the test procedure to qualify the boards are described. Finally the performance results, the temperature studies and high rate tests are shown and discussed.
DSP Online Algorithms for The ATLAS TileCal Read-Out Drivers
TileCal is the hadronic tile calorimeter of the ATLAS experiment at LHC/CERN. The central element of the back-end system of the TileCal detector is the read-out driver (ROD).The main components of the TileCal ROD are the digital signal processors (DSPs) placed on the processing unit (PU) daughterboards. This paper presents a detailed description of the code developed for the DSPs. The code is divided into two different parts: the first part contains the core functionalities and the second part the reconstruction algorithms. The core acts as an operating system and controls configuration, data reception and transmission and synchronization between front-end data and the timing, trigger and c…
A layer correlation technique for pion energy calibration at the 2004 ATLAS Combined Beam Test
A new method for calibrating the hadron response of a segmented calorimeter is developed and successfully applied to beam test data. It is based on a principal component analysis of energy deposits in the calorimeter layers, exploiting longitudinal shower development information to improve the measured energy resolution. Corrections for invisible hadronic energy and energy lost in dead material in front of and between the calorimeters of the ATLAS experiment were calculated with simulated Geant4 Monte Carlo events and used to reconstruct the energy of pions impinging on the calorimeters during the 2004 Barrel Combined Beam Test at the CERN H8 area. For pion beams with energies between 20GeV…
TileCal optical multiplexer board 9U prototype
This paper presents the architecture and the status of the optical multiplexer board (OMB) for the ATLAS/LHC Tile hadronic calorimeter (TileCal). This board will analyze the front-end data CRC to prevent bit and burst errors produced by radiation. Besides, due to its position within the data acquisition chain it will be used to emulate front-end data for tests. The first two prototypes of the final OMB 9U version have been produced at CERN. Detailed design issues and manufacture features of these prototypes are described. These prototypes are being validated whereas some firmware developments are being implemented in the programmable devices of the board. Functional descriptions of the boar…
Algorithms for the ROD DSP of the ATLAS Hadronic Tile Calorimeter
In this paper we present the performance of two algorithms currently running in the Tile Calorimeter Read-Out Driver boards for the commissioning of ATLAS. The first algorithm presented is the so called Optimal Filtering. It reconstructs the deposited energy in the Tile Calorimeter and the arrival time of the data. The second algorithm is the MTag which tags low transverse momentum muons that may escape the ATLAS muon spectrometer first level trigger. Comparisons between online (inside the Read-Out Drivers) and offline implementations are done with an agreement around 99% for the reconstruction of the amplitude using the Optimal Filtering algorithm and a coincidende of 93% between the offli…
Development of the optical multiplexer board prototype for data acquisition in TileCal experiment
The optical multiplexer board is one of the elements present in the read out chain of the tile calorimeter in ATLAS experiment. Due to radiation effects, two optical fibers with the same data come out from the front end boards to this board, which has to decide in real time which one carries good data and pass them to the read out driver motherboard for processing. This paper describes the design and tests of the first prototype, implemented as a 6U VME64x slave module, including both hardware and firmware aspects. In this last, algorithms for cyclic redundancy code checking are used to make the decision. Besides, the board may be used as a data injector for testing purposes of the read out…
The Large Hadron–Electron Collider at the HL-LHC
The Large Hadron-Electron Collider (LHeC) is designed to move the field of deep inelastic scattering (DIS) to the energy and intensity frontier of particle physics. Exploiting energy-recovery technology, it collides a novel, intense electron beam with a proton or ion beam from the High-Luminosity Large Hadron Collider (HL-LHC). The accelerator and interaction region are designed for concurrent electron-proton and proton-proton operations. This report represents an update to the LHeC's conceptual design report (CDR), published in 2012. It comprises new results on the parton structure of the proton and heavier nuclei, QCD dynamics, and electroweak and top-quark physics. It is shown how the LH…
Study of energy response and resolution of the ATLAS barrel calorimeter to hadrons of energies from 20 to 350 GeV
A fully instrumented slice of the ATLAS detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the results of the measurements of the response of the barrel calorimeter to hadrons with energies in the range 20 to 350 GeV and beam impact points and angles corresponding to pseudorapidity values in the range 0.2-0.65 are reported. The results are compared to the predictions of a simulation program using the Geant 4 toolkit.
The Optical Multiplexer Board for the ATLAS Hadronic Tile Calorimeter
This paper presents the architecture and the status of the optical multiplexer board (OMB) for the ATLAS/LHC tile hadronic calorimeter (TileCal). This board will analyze the front-end data CRC to prevent bit and burst errors produced by radiation. Besides, due to its position within the data acquisition chain it will be used to emulate front-end data for tests. The first two prototypes of the final OMB 9U version have been produced at CERN. Detailed design issues and manufacturing features of these prototypes are described. These prototypes are being validated while firmware developments are being implemented in the programmable devices of the board.
Study of the response of the ATLAS central calorimeter to pions of energies from 3 to 9 GeV
Çetin, Serkant Ali (Dogus Author) A fully instrumented slice of the ATLAS central detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the response of the central calorimeters to pions with energies in the range between 3 and 9 GeV is presented. The linearity and the resolution of the combined calorimetry (electromagnetic and hadronic calorimeters) was measured and compared to the prediction of a detector simulation program using the toolkit Geant 4.
A search for new physics in dijet mass and angular distributions in pp collisions at [subscript √s=7] TeV measured with the ATLAS detector
A search for new interactions and resonances produced in LHC proton–proton (pp) collisions at a centre-of-mass energy ps = 7 TeV was performed with the ATLAS detector. Using a dataset with an integrated luminosity of 36 pb−1, dijet mass and angular distributions were measured up to dijet masses of 3.5 TeV and were found to be in good agreement with Standard Model predictions. This analysis sets limits at 95% CL on various models for new physics: an excited quark is excluded for mass between 0.60 and 2.64 TeV, an axigluon hypothesis is excluded for axigluon masses between 0.60 and 2.10 TeV and quantum black holes are excluded in models with six extra space–time dimensions for quantum gravity…