Search results for " Hardware"
showing 10 items of 422 documents
Exploring FPGA‐Based Lock‐In Techniques for Brain Monitoring Applications
2017
Functional near‐infrared spectroscopy (fNIRS) systems for e‐health applications usually suffer from poor signal detection, mainly due to a low end‐to‐end signal‐to‐noise ratio of the electronics chain. Lock‐in amplifiers (LIA) historically represent a powerful technique helping to improve performance in such circumstances. In this work a digital LIA system, based on a Zynq® field programmable gate array (FPGA) has been designed and implemented, in an attempt to explore if this technique might improve fNIRS system performance. More broadly, FPGA‐based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and its …
A Prototype of Wireless Sensor for Data Acquisition in Energy Management Systems
2018
A prototype of a wireless sensor for monitoring electrical loads in a smart building is designed and implemented. The sensor can acquire the main electrical parameters of the connected load and, optionally, other physical quantities (e.g., room temperature). Unlike other wireless sensors in literature, the proposed sensor is cheap and small, exploits the Wi-Fi network that is commonly available inside buildings, and uses a lightweight message-based communication paradigm. Besides the sensor node, two management nodes are also implemented to manage sensor reconfiguration and the persistence of data. The measured data are stored in an SQLite database and can be used for various purposes, e.g.…
The upgraded HADES trigger and data acquisition system
2011
The HADES experiment is a High Acceptance Di-Electron Spectrometer located at GSI in Darmstadt, Germany. Recently, its trigger and data acquisition system was upgraded. The main goal was to substantially increase the event rate capability by a factor of up to 20 to reach 100 kHz in light and 20 kHz in heavy ion reaction systems. The total data rate written to storage is about 400 MByte/s in peak.In this context, the complete read-out system was exchanged to FPGA-based platforms using optical communication. For data transport a general-purpose real-time network protocol was developed to meet the strong requirements of the system. In particular, trigger information has to reach all front-end …
Nanoseconds Timing System Based on IEEE 1588 FPGA Implementation
2019
Clock synchronization procedures are mandatory in most physical experiments where event fragments are readout by spatially dislocated sensors and must be glued together to reconstruct key parameters (e.g. energy, interaction vertex etc.) of the process under investigation. These distributed data readout topologies rely on an accurate time information available at the frontend, where raw data are acquired and tagged with a precise timestamp prior to data buffering and central data collecting. This makes the network complexity and latency, between frontend and backend electronics, negligible within upper bounds imposed by the frontend data buffer capability. The proposed research work describ…
The JYFLTRAP control and measurement system
2008
The JYFLTRAP setup has been used for precision mass spectrometry since 2003. An essential part of this setup is the computer-controlled system consisting of software and hardware that is required to operate the instruments. The software has been developed solely at JYFL using LabVIEW and C++ development tools. The hardware consists of devices controlled using Control Area Network (CAN) field bus and Ethernet for communication purposes. LAN/GPIB-gateways, modular multichannel ISEG DC power supplies and WAGO I/O systems are also used.
Present state of the MAMI control system
1990
Abstract MAMI (Mainz Microtron) is an electron accelerator consisting of a cascade of three race-track microtrons, with an output electron beam of 855 MeV and 100 μA cw [1]. The first two stages (output energy 180 MeV) were operative for nuclear-physics experiments from 1983 to 1987 and have since been transferred to a new building. They will serve as an injector for the third stage, now under construction. The control system for MAMI was based on a versatile process communication software system for a network of processors with multiprocess operating systems. This system has previously proved very successful, so we decided to rely on it as control system for the new, upgraded accelerator, …
MECDAS/spl minus/a distributed data acquisition system for experiments at MAMI
1994
For coincidence experiments with the three-spectrometer setup at MAMI an experiment control and data acquisition system has been built and was put successfully into final operation in 1992. MECDAS is designed as a distributed system using communication via Ethernet and optical links. At the front end, VMEbus systems are used for real time purposes and direct hardware access via CAMAC, Fastbus or VMEbus. RISC workstations running UNIX are used for monitoring, data archiving and online and offline analysis of the experiment. MECDAS consists of several fixed programs and libraries, but large parts of readout and analysis can be configured by the user. Experiment specific configuration files ar…
Hardware and firmware developments for the upgrade of the ATLAS Level-1 Central Trigger Processor
2014
The Central Trigger Processor (CTP) is the final stage of the ATLAS first level trigger system which reduces the collision rate of 40 MHz to a Level-1 event rate of 100 kHz. An upgrade of the CTP is currently underway to significantly increase the number of trigger inputs and trigger combinations, allowing additional flexibility for the trigger menu. We present the hardware and FPGA firmware of the newly designed core module (CTPCORE+) module of the CTP, as well as results from a system used for early firmware and software prototyping based on commercial FPGA evaluation boards. First test result from the CTPCORE+ module will also be shown.
Adaptive independent sticky MCMC algorithms
2018
In this work, we introduce a novel class of adaptive Monte Carlo methods, called adaptive independent sticky MCMC algorithms, for efficient sampling from a generic target probability density function (pdf). The new class of algorithms employs adaptive non-parametric proposal densities which become closer and closer to the target as the number of iterations increases. The proposal pdf is built using interpolation procedures based on a set of support points which is constructed iteratively based on previously drawn samples. The algorithm's efficiency is ensured by a test that controls the evolution of the set of support points. This extra stage controls the computational cost and the converge…
Complete End-To-End Low Cost Solution To a 3D Scanning System with Integrated Turntable
2017
3D reconstruction is a technique used in computer vision which has a wide range of applications in areas like object recognition, city modelling, virtual reality, physical simulations, video games and special effects. Previously, to perform a 3D reconstruction, specialized hardwares were required. Such systems were often very expensive and was only available for industrial or research purpose. With the rise of the availability of high-quality low cost 3D sensors, it is now possible to design inexpensive complete 3D scanning systems. The objective of this work was to design an acquisition and processing system that can perform 3D scanning and reconstruction of objects seamlessly. In addition…