Search results for " Mechanical engineering"
showing 10 items of 623 documents
Recent progress in developing a feasible and integrated conceptual design of the WCLL BB in EUROfusion project
2019
The water-cooled lithium-lead breeding blanket is in the pre-conceptual design phase. It is a candidate option for European DEMO nuclear fusion reactor. This breeding blanket concept relies on the liquid lithium-lead as breeder-multiplier, pressurized water as coolant and EUROFER as structural material. Current design is based on DEMO 2017 specifications. Two separate water systems are in charge of cooling the first wall and the breeding zone: thermo-dynamic cycle is 295–328 °C at 15.5 MPa. The breeder enters and exits from the breeding zone at 330 °C. Cornerstones of the design are the single module segment approach and the water manifold between the breeding blanket box and the back suppo…
Buckling and nonlinear dynamics of elastically coupled double-beam systems
2016
Abstract This paper deals with damped transverse vibrations of elastically coupled double-beam system under even compressive axial loading. Each beam is assumed to be elastic, extensible and supported at the ends. The related stationary problem is proved to admit both unimodal (only one eigenfunction is involved) and bimodal (two eigenfunctions are involved) buckled solutions, and their number depends on structural parameters and applied axial loads. The occurrence of a so complex structure of the steady states motivates a global analysis of the longtime dynamics. In this regard, we are able to prove the existence of a global regular attractor of solutions. When a finite set of stationary s…
Tensile behaviour of anti-symmetric CFRP composite
2011
Abstract This paper addresses the response of a 17-ply anti-symmetric carbon/epoxy composite subjected to uniaxial tensile loading. Hashin ply damage model is adopted to describe the damage behaviour of the plies, whereas damage initiation and progression of the interfaces are characterised by mixed-mode cohesive damage model. Force-displacement curves obtained numerically and experimentally show good agreement. Results show that all laminae and interfaces experience the damage except laminae with 0o fibre. In addition, damage is concentrated at the tab and central regions of the tensile specimen. Edge delamination is observed in all interfaces.
On the spectral moments of non-WSSUS mobile-to mobile double-Rayleigh fading channels
2017
This paper deals with the mathematical analysis of the spectral moments of non-wide-sensestationary uncorrelated-scattering (non-WSSUS) mobile-to-mobile (M2M) double-Rayleigh fading channels. The point of departure is a recently proposed geometry-based statistical model (GBSM) for M2M double-Rayleigh fading channels from which general analytical expressions are derived for the average Doppler shift, Doppler spread, average delay, and delay spread. Closed-form solutions of such expressions are presented for the particular case of the geometrical two-rings scattering model. The obtained results indicate that the average Doppler shift and Doppler spread are directly influenced by not only the …
A note on the higher order strain and stress tensors within deformation gradient elasticity theories: Physical interpretations and comparisons
2016
Abstract Higher order strain and stress tensors encompassed within gradient elasticity theories are discussed with a particular concern to the physical meaning of double and triple stresses. A single rule is shown to hold for the physical interpretation of the indices of a higher order stress tensor both within distortion gradient and strain gradient theories, whereas the analogous Mindlin’s rule holds only within distortion gradient theories. Double and triple stresses are discussed separately with the aid of simple illustrative examples. A corrigendum to a previous paper by the author (IJSS 50 (2013) 3749–3765) is also presented.
Centrifuge tests on strip footings on sand with a weak layer
2017
Tests on small-scale physical models of a strip footing resting on a dense sand bed containing a thin horizontal weak soil layer were carried out at normal gravity (1 g ). The results, reported in a companion paper, point out that the weak layer plays an important role in the failure mechanism and the ultimate bearing capacity of the footing if it falls within the ground volume relevant to the behaviour of the sand–footing system. The same problem was also investigated by means of centrifuge tests on reduced-scale models at 25 g and 40 g . The results of these tests, reported and discussed in this paper, confirm that failure mechanisms are governed substantially by the presence of the weak…
Application of Genetic Algorithm on Parameter Optimization of Three Vehicle Crash Scenarios
2017
Abstract This paper focuses on the development of mathematical models for vehicle frontal crashes. The models under consideration are threefold: a vehicle into barrier, vehicle-occupant and vehicle to vehicle frontal crashes. The first model is represented as a simple spring-mass-damper and the second case consists of a double-spring-mass-damper system, whereby the front mass and the rear mass represent the vehicle chassis and the occupant, respectively. The third model consists of a collision of two vehicles represented by two masses moving in opposite directions. The springs and dampers in the models are nonlinear piecewise functions of displacements and velocities respectively. More spec…
The Behaviour of Mistuned Piezoelectric Shunt Systems and Its Estimation
2016
This paper addresses monoharmonic vibration attenuation using piezoelectric transducers shunted with electric impedances consisting of a resistance and an inductance in series. This type of vibration attenuation has several advantages but suffers from problems related to possible mistuning. In fact, when either the mechanical system to be controlled or the shunt electric impedance undergoes a change in their dynamical features, the attenuation performance decreases significantly. This paper describes the influence of biases in the electric impedance parameters on the attenuation provided by the shunt and proposes an approximated model for a rapid prediction of the vibration damping performa…
Magnesium alloys (WE43 and ZE41) characterisation for laser applications
2004
International audience; One of the most important parameters in laser treatment is the quantity of beam energy absorbed by the substrate. Despite its important role played in laser processes, this factor is rarely available for the laser sources wavelengths and at high temperatures reached during such treatments. A series of experiments were carried out in order to characterise, from this point of view, two types of magnesium alloys, WE43 and ZE41, often used in laser applications (cladding, alloying, welding, etc.). The results represent an important step in order to understand Mg-alloys behaviour under laser beam action.
Reverse electrodialysis heat engine for sustainable power production
2017
Abstract Reverse Electrodialysis Heat Engine (REDHE) is a promising technology to convert waste heat at temperatures lower than 100 °C into electric power. In the present work an overview of the possible regeneration methods is presented and the technological challenges for the development of the RED Heat Engine (REDHE) are identified. The potential of this power production cycle was investigated through a simplified mathematical model. In the first part of the work, several salts were singularly modelled as possible solutes in aqueous solutions feeding the RED unit and the corresponding optimal conditions were recognized via an optimization study. In the second part, three different RED He…