Search results for " Production"
showing 10 items of 5274 documents
Carbon emission along a eutrophication gradient in temperate riverine wetlands: effect of primary productivity and plant community composition
2016
International audience; 1. Eutrophication increases primary productivity and favours the predominance of floating vegetation in wetlands. Carbon (C) fluxes in wetlands are strongly driven by primary productivity and can differ by vegetation type. However, to the best of our knowledge, the role of eutrophication in C fluxes has rarely been assessed. 2. Consequently, we aimed to measure the seasonal variation in carbon dioxide (CO2) and methane (CH4) fluxes at six aquatic sites in four temperate wetlands, ranging along a gradient of sediment total phosphorus content, and determine whether C fluxes correlate with above-ground net primary productivity (ANPP) and plant community composition alon…
Food Quality, Sensory Attributes and Nutraceutical Value of Fresh “Osteen” Mango Fruit Grown under Mediterranean Subtropical Climate Compared to Impo…
2020
Mango is a fruit with a very short shelf-life due to its rapid ripeness after harvest
Impact Analysis Using Life Cycle Assessment of Asphalt Production from Primary Data
2020
Road construction and maintenance have a great impact on the environment, owing to the huge volumes of resources involved. Consequently, current production procedures and technologies must be properly investigated, for identifying and quantifying the life cycle environmental impacts produced. In this paper, primary data, i.e., site-specific data directly collected or measured on a reference plant, are analyzed for calculating the impact of the production of a hot mix asphalt. The analysis is performed in a from &ldquo
A new strategy to maximize organic matter valorization in municipalities: combination of urban wastewater with kitchen food waste and its treatment w…
2017
[EN] The aim of this study was to evaluate the feasibility of treating the kitchen food waste (FW) jointly with urban wastewater (WW) in a wastewater treatment plant (WWTP) by anaerobic membrane technology (AnMBR). The experience was carried out in six different periods in an AnMBR pilot-plant for a total of 536 days, varying the SRT, HRT and the food waste penetration factor (PF) of food waste disposers. The results showed increased methane production of up to 190% at 70 days SRT, 24 hours HRT and 80% PF, compared with WW treatment only. FW COD and biodegradability were higher than in WW, so that the incorporation of FW into the treatment increases the organic load and the methane producti…
Orchestrated learning: creating a company-specific production system (XPS)
2021
Purpose Companies create company-specific production systems (XPS) by tailoring generic concepts to fit their unique situation. However, little is known about how an XPS is created. This paper aims to provide insights into the creation of an XPS. Design/methodology/approach A retrospective case study was conducted in a Norwegian multinational company over the period 1991–2006, using archival data and interviews. Findings The development of the XPS did not start with a master plan. Instead, dispersed existing initiatives were built upon, along with an external search for novel ideas. Widespread experimentation took place, only later to be combined into a coherent approach. Once established,…
A simulated annealing-based approach for the joint optimization of production/inventory and preventive maintenance policies
2017
Even if more reliable than the past, the performance of modern manufacturing systems is still affected by machine’s deteriorations and breakdowns. As a consequence, adequate maintenance programs must be implemented to adequately satisfy demands during manufacturing stops due to unexpected failures or preventive maintenance (PM) actions. Despite production and maintenance are closely related issues, their joint optimization has become an important research topic just during the last decade. Therefore, the present paper proposes a model for the combined optimization of production/inventory control and PM policies with the aim of minimizing the total expected cost per unit time. The model is f…
Surface Characteristics of Machined Polystyrene with 3D Printed Thermoplastic Tool
2020
An effort is made in this work to appraise the surface characteristics of machined expandable polystyrene (EPS) with a novel 3D printed thermoplastic acrylonitrile-butadiene-styrene (ABS) tool. Linear grooves on EPS were made on a vertical milling machine that was modified to conduct experiments in the laboratory. The tests were designed as per the Taguchi L9 based factorial design of experimentation while varying process parameters such as depth of cut, spindle speed, and feed rate. The machining responses dimensional accuracy and surface roughness of the machined grooves were studied. Furthermore, the surface topography of the machined specimens was considered to investigate the mechanism…
Optimization Model to Extend Existing Production Planning and Control Systems for the Use of Additive Manufacturing Technologies in the Industrial Pr…
2018
Abstract The use of additive manufacturing technologies for industrial production is constantly growing. This technology differs from the known production procedures. The areas of scheduling, detailed and sequence planning are particularly important for additive production due to the long print times and flexible use of the production area. Therefore, production-relevant variables are considered and used for the production planning and control (PPC) of additive manufacturing machines. For this purpose, an optimization model is presented which shows a time-oriented build space utilization. In the implementation, a nesting algorithm is used to check the combinability of different models for e…
Crowd-Averse Robust Mean-Field Games: Approximation via State Space Extension
2016
We consider a population of dynamic agents, also referred to as players. The state of each player evolves according to a linear stochastic differential equation driven by a Brownian motion and under the influence of a control and an adversarial disturbance. Every player minimizes a cost functional which involves quadratic terms on state and control plus a cross-coupling mean-field term measuring the congestion resulting from the collective behavior, which motivates the term “crowd-averse.” Motivations for this model are analyzed and discussed in three main contexts: a stock market application, a production engineering example, and a dynamic demand management problem in power systems. For th…
Do terrorism, organized crime (drug production), and state weakness affect contemporary armed conflicts? An empirical analysis
2015
ABSTRACTIn 2014, the UN Security Council emphasized the dangers of terrorism, criminal activity (especially drug production and trafficking), and state weakness in conflict areas. However, neither policy debates nor scholarly analyses have focussed on the potential impact of these elements on conflict dynamics and characteristics, and the investigated partial relationships have led to inconclusive results. This article explores the presence in armed conflicts of terrorist groups among fighting parties, major drug production (indicating the presence of activities typical of criminal organizations), and state failure in the period 1990–2011. Focussing on intrastate conflicts, this article hig…