Search results for " SCIENZA"
showing 10 items of 1301 documents
Anti-/Pro-Oxidant Behavior of Naturally Occurring Molecules in Polymers and Biopolymers: A Brief Review
2019
Polymers and biopolymers are continuously subjected to the action of different stress factors, such as oxygen, heat, UV light, mechanical stress, humidity, etc., during their processing and service life, undergoing overall oxidative degradation, that causes performance and property deterioration. To improve the resistance at high temperatures and long-term weatherability of the polymers and biopolymers, usually, during their manufacturing, synthetic antioxidants and UV-light stabilizers are added. In the past decade, several concerns related to the impact of the synthetic stabilizers have emerged, and to reduce their negative effect on human health and the environment, their replacement wit…
Characterization and Processability of Blends of Polylactide Acid with a New Biodegradable Medium-Chain-Length Polyhydroxyalkanoate
2015
In this work the processability and the mechanical performance of polylactide acid (PLA) based blends with a sample of a new biodegradable medium-chain-length poly (hydroxyalkanoate) (PHA) were investigated. The two polymers are incompatible with scarce adhesion and with the dispersed PHA particles size increasing with the PHA content. Rheological tests in shear flow indicate that adding PHA improves the processability of the matrix by increasing the content of this second component in the blend, as observed also for the torque curves, due to the very low viscosity of this new sample of PHA. The processability is only slightly worsened in non-isothermal elongational flow as the melt strengt…
Melt stabilization of wet polyamide 6
2002
Abstract Melt processing of polycondensate polymers must be carried out after careful drying in order to avoid any hydrolytic chain scission caused by the presence of water or other small molecules. In this work, the effect of two different antioxidants on the processing and flow properties of a polyamide 6 sample not dried before processing operations has been studied. One of these stabilizers seems to protect the wet polymer from hydrolytic chain scission. This action has been interpreted considering that the stabilizer hydrolyses instead of the polyamide macromolecules.
High energy radiation cure of resin systems for structural adhesives and composite applications
2002
Abstract Radiation cure polymerisation of a commercial diglycidyl ether of bisphenol F epoxy resin has been achieved using a 60Co irradiation source, compounding the monomer with few percentage of an onium salt catalyst. The cure process has been monitored by a gamma-calorimetric technique and systems irradiated at doses corresponding to different positions in the gamma-calorimetric curve have been characterised via solubility tests and dynamic mechanical torsion analysis. Changes in both the measured gel fractions and tan δ values were associated with the progress of polymerisation and crosslinking reactions and these were dose dependent. Furthermore, systems irradiated at lower doses exhi…
Polymeric scaffolds based on blends of poly-l-lactic acid (PLLA) with poly-d-l- lactic acid (PLA) prepared via thermally induced phase separation (TI…
2012
Porous scaffolds based on blends of high crystalline Poly-L-lactic acid (PLLA) with low crystalline poly-D-L-lactic acid (PLA) were prepared via Ther- mally Induced Phase Separation (TIPS), with the aim of exploring the possibility to control the degradation behaviour of the PLA-based scaffold, simultaneously pre- serving the morphological characteristics required for tissue engineering applica- tions. Porous foams with different PLLA/PLA weight ratios (from 95/5 to 60/40) were produced and characterised in terms of pore size, porosity, and thermal properties. The scaffolds present an open porosity, with average pore sizes ranging from 30 to 70 lm. Results showed that, when dealing with a P…
Photocatalytic oxidation of trans-ferulic acid to vanillin on TiO2 and WO3-loaded TiO2 catalysts
2015
Abstract The photocatalytic oxidation of trans-ferulic acid to vanillin in water has been studied by using various TiO2 and WO3-loaded TiO2 samples as catalysts. Different values of selectivity were obtained depending on the physico-chemical properties of the single samples and a vanillin selectivity of 10% was reached in the presence of the commercial TiO2 Merck. Higher selectivity values were obtained by impregnation of TiO2 with H2WO4 followed by calcination. The increased production of vanillin exhibited by the obtained WO3-loaded TiO2 powders was attributed to a reduced further oxidation of the aldehyde caused by the presence of the practically inactive tungsten trioxide hydrate on the…
No-Flow Temperature in Injection Molding Simulation
2010
Most injection molding simulation packages use the no-flow temperature (NFT) as a means of determining whether the polymer flows or is solid. The NFT is not well defined, and a standard method for measuring it does not exist. A sensitivity analysis of the filling stage has been carried out with two different packages [VISI Flow (Vero Software Limited, Gloucestershire, UK) and Moldflow (Autodesk, Inc., San Rafael, CA)] to estimate the influence of the NFT on the main processing parameters. The NFT has a large influence on the thickness of the frozen layer, but it does not appreciably affect the filling pressure. Because the NFT affects the frozen layer, an effect on the estimation of shrinka…
Effect of small amounts of poly(lactic acid) on the recycling of poly(ethylene terephthalate) bottles
2011
Abstract Poly(ethylene terephthalate) (PET) is one of the most used commodity polymers, especially for food and beverage applications, and its recycling is of great importance because of the possible use in the textile and construction industries. On the other hand, the interest in biodegradable polymers has led, in recent years, to the use of materials such as poly(lactic acid) (PLA) also in the food and beverage industry. The presence of small amounts of PLA in the PET waste can significantly affect the post-consumer recycling process. In this work, the effect of the presence of small amounts of PLA on the recycling of PET bottles is investigated by rheological, mechanical, morphological …
Gamma radiation of EVA-AA/MMA swollen systems to obtain mechanically improved blends
2002
In this work a "new" way to obtain "compatibilised" blends of rubber-glassy thermoplastic components is presented. Polyethylen-vinyl acetate acrylic acid terpolymer is swollen by methylmetacrylate and the system is irradiated through gamma rays in order to induce polymerisation of the monomer. Solubility and dynamic mechanical tests indicate the formation of a two phase system, even though in presence of strong interactions between the two components. Mechanical tensile behaviour is that of a ductile material with appreciable modulus values.
Mode I fracture toughness behavior of hydro-thermally aged carbon fibre reinforced DGEBA-HHPA-PES systems
2012
In this work the Mode I fracture toughness behavior of unidirectional CFRP laminates is investigated by means of Double Cantilever Beam (DCB) tests. The composite samples were manufactured by thermal curing after impregnation of a Carbon fabric with a DGEBA epoxy and anhydride HHPA curing agent. One resin batch was also mixed with a PES thermoplastic monomer to enhance the matrix toughness. Two lots of samples, toughened and un-toughened, were then left to soak in hot water to achieve various degrees of aging. The influence of matrix toughening and hydrothermal aging on the delamination behavior of the composite have then been assessed and correlated with characterization data from Dynamic …