Search results for " Sensor."
showing 10 items of 1700 documents
Energy Harvesting Powered Packet Transmissions in Duty-Cycled WSNs: A DTMC Analysis
2017
Energy harvesting (EH) promises an extended lifetime for wireless sensor networks (WSNs), supplying sensor nodes with accumulated energy from natural sources. Different from battery powered sensors, nodes in EH-enabled WSNs are equipped with an energy harvesting accessory in order to extract energy from surrounding sources. Based upon the harvested energy, sensor nodes perform data exchange activities. In this paper, we develop two discrete time Markov chain (DTMC) models to analyze the performance of packet transmissions in such a WSN while employing a generic synchronous medium access control (MAC) protocol. Using the proposed DTMC models, we investigate the effect of EH over a specific s…
Collision Avoidance in Wake-Up Radio Enabled WSNs: Protocol and Performance Evaluation
2018
In wake-up radio (WuR) enabled wireless sensor networks (WSNs), the envisaged application scenarios are primarily targeted at low traffic load conditions. When applying WuR to medium or heavy traffic load scenarios, however, collisions among wake-up calls (WuCs) may happen, resulting in a lower packet delivery ratio (PDR). In this paper, we propose a media access control protocol for WuR- enabled WSN that is capable of avoiding WuC collisions by activating a contention-based collision avoidance mechanism for WuC transmissions. The performance of the proposed protocol is evaluated by a Markov chain based mathematical model and is compared with a WuR protocol that performs only clear channel as…
Event-Triggered Sleeping for Synchronous DC MAC IN WSNs: Mechanism and DTMC Modeling
2016
Overhearing and idle listening are two primary sources for unnecessary energy consumption in wireless sensor networks. Although introducing duty cycling in medium access control (MAC) reduces idle listening, it cannot avoid overhearing in a network with multiple contending nodes. In this paper, we propose an event-triggered sleeping (ETS) mechanism for synchronous duty-cycled (DC) MAC protocols in order to avoid overhearing when a node is not active. This ETS mechanism applies to any synchronous DC MAC protocols and makes them more energy efficient. Furthermore, we develop a two dimensional discrete time Markov chain model to evaluate the performance of the proposed ETS mechanism by integra…
Energy Efficient Consecutive Packet Transmissions in Receiver-Initiated Wake-Up Radio Enabled WSNs
2018
In wake-up radio (WuR)-enabled wireless sensor networks, data communication among nodes is triggered in an on-demand manner, by either a sender or a receiver. For receiver-initiated WuR (RI-WuR), a receiving node wakes up sending nodes through a wake-up call. Correspondingly sending nodes transmit packets in a traditional way by competing with one another multiple times in a single operational cycle. In this paper, we propose a receiver-initiated consecutive packet transmission WuR (RI-CPT-WuR) medium access control (MAC) protocol, which eliminates multiple competitions to achieve higher energy efficiency. Furthermore, we develop two associated discrete time Markov chains (DTMCs) for evalua…
Bezvadu sensoru tīkla maršrutēšanas protokola izstrāde
2022
Maģistra darba “Bezvadu sensoru tīkla maršrutēšanas protokola izstrāde” mērķis ir izpētīt citu autoru sniegumu maršrutēšanas protokolu modeļu izstrādē, aplūkot maršrutēšanas protokolus, kuri izmanto paredzēšanu, modeļus, kā arī aplūkot bezvadu sensoru tīklu simulatora rīkus, kurus izmanto protokolu izstrādē. Papildus tam, mērķis ir arī izveidot un notestēt savu maršrutēšanas protokolu, kas paredz ziņas piegādes iespējamību konkrētajam mezglam un maršrutēšanas izvēlei izmanto dienu, laika periodu un šo paredzēto vērtību. Bezvadu sensoru tīklos galvenā problēma vienmēr ir bijusi enerģijas patēriņš, tāpēc ar šāda protokola palīdzību mērķis ir samazināt tīklā apraidāmo ziņojumu skaitu, tādā vei…
ALD thin ZnO layer as an active medium in a fiber-optic Fabry–Perot interferometer
2015
Abstract A novel optical fiber sensor of temperature using a thin ZnO layer fabricated by atomic layer deposition (ALD) is demonstrated for the first time. The thin ZnO layer was grown on the face of a standard optical telecommunication fiber SMF-28 and operates as a Fabry–Perot interferometer sensitive to temperature. The interferometer characterization was made in the temperature range extending from 50 to 300 °C with resolution equal to 1 °C. The output signal was analyzed by measurement of the shift of the maxima in spectral pattern. The sensitivity of temperature measurement is about 0.05 nm/°C. Furthermore, very good linearity of the sensor was achieved with correlation coefficient R2…
Measurement of UV-induced absorption and scattering losses in photosensitive fibers
2018
UV-assisted fabrication of gratings using photosensitive fibers is a well-established technique, based on the UV-induced permanent modification of the refractive index of the fiber material. As a result, the absorption coefficient is also changed. Here, we exploit the thermal sensitivity of whispering gallery mode resonances of the fiber itself to measure the profile of the heating along an irradiated fiber versus the input power and for different UV radiation intensities. Our technique allows discriminating between the absorption and scattering contributions to the overall losses, by comparing the results obtained with our technique with direct transmission measurements. Different photosen…
Photo-acoustic excitation and optical detection of fundamental flexural guided wave in coated bone phantoms.
2013
Abstract Photo-acoustic (PA) imaging was combined with skeletal quantitative ultrasound (QUS) for assessment of human long bones. This approach permitted low-frequency excitation and detection of ultrasound so as to efficiently receive the thickness-sensitive fundamental flexural guided wave (FFGW) through a coating of soft tissue. The method was tested on seven axisymmetric bone phantoms, whose 1- to 5-mm wall thickness and 16-mm diameter mimicked those of the human radius. Phantoms were made of a composite material and coated with a 2.5- to 7.5-mm layer of soft material that mimicked soft tissue. Ultrasound was excited with a pulsed Nd:YAG laser at 1064-nm wavelength and received on the s…
Assessment of the cortical bone thickness using ultrasonic guided waves: Modelling and in vitro study
2007
Determination of cortical bone thickness is warranted, e.g., for assessing the level of endosteal resorption in osteoporosis or other bone pathologies. We have shown previously that the velocity of the fundamental antisymmetric (or flexural) guided wave, measured for bone phantoms and bones in vitro, correlates with the cortical thickness significantly better than those by other axial ultrasound methods. In addition, we have introduced an inversion scheme based on guided wave theory, group velocity filtering and 2-D fast Fourier transform, for determination of cortical thickness from the measured velocity of guided waves. In this study, the method was validated for tubular structures by usi…
Determination of Bubble Size Distribution Using Ultrasound Array Imaging
2020
In this article, ultrasonic phased arrays are deployed as an imaging tool for industrial process analysis. Such arrays are typically used for sonar, medical diagnosis, and nondestructive testing; however, they have not yet been applied to industrial process analysis. The precise positioning of array elements and high frequencies possible with this technology mean that highly focused images can be generated, which cannot currently be achieved using ultrasound tomography. This article aims to highlight the potential of this technology for the measurement of bubble size distribution (BSD) and to demonstrate its application to both intrusive and noninvasive process measurements. Ultrasound imag…