Search results for " Solar cell"
showing 10 items of 309 documents
Band unpinning and photovoltaic model for P3HT:PCBM organic bulk heterojunctions under illumination
2008
Capacitance analysis of P3HT:PCBM bulk heterojunction solar cells, in dark and under illumination, shows a linear Mott-Schottky characteristic at moderate reverse bias, indicating p-doping of the organic blend. The flatband potential under illumination is displaced negatively about 0.6 V with respect to dark conditions. A basic photovoltaic model is developed to explain this, in terms of electron transfer via surface states at the metal/organic interface. Surface states with a slow exchange kinetics, become charged under illumination, unpinning the band and decreasing the depletion layer at the electron extraction contact. This becomes a major factor limiting the performance of bulk heteroj…
Numerical analysis of light soaking phenomenon in Ruthenium based Dye Sensitized Solar Cells
2017
Dye Sensitized Solar Cells (DSSCs) are widely considered one of the most promising third generation photovoltaic devices, especially thanks to their relatively low cost if compared to conventional solar cells. An interesting phenomenon affecting such devices is the so-called light soaking effect, consisting in the increase of cell main electrical parameters after the exposition to solar light. In this work, starting from the experimental characterization carried out on Ruthenium-based DSSCs, we report on a series of numerical analysis performed to better describe the above-mentioned light soaking effect in order to show the relationship between such phenomenon and the main physical paramete…
Investigation of recovery mechanisms in dye sensitized solar cells
2016
Abstract We study the spontaneous recovery phenomenon displayed by solar cells sensitized with a ruthenium complex-based dye N719, which manifests with the increase over the time (from several minutes up to some days) of the short circuit current density J sc and the open circuit voltage V oc , during cell illumination. Under dark conditions the current decreases over time after the application of forward bias voltages. We investigate the effects of temperature and electrolyte composition by means of current–voltage measurements and electrochemical impedance spectroscopy, both under dark and illumination conditions. The main result is that the recovery of the performances depends on the cha…
ZnS Ultrathin interfacial layers for optimizing carrier management in Sb2S3-based photovoltaics
2021
Antimony chalcogenides represent a family of materials of low toxicity and relative abundance, with a high potential for future sustainable solar energy conversion technology. However, solar cells based on antimony chalcogenides present open-circuit voltage losses that limit their efficiencies. These losses are attributed to several recombination mechanisms, with interfacial recombination being considered as one of the dominant processes. In this work, we exploit atomic layer deposition (ALD) to grow a series of ultrathin ZnS interfacial layers at the TiO2/Sb2S3 interface to mitigate interfacial recombination and to increase the carrier lifetime. ALD allows for very accurate control over th…
Enamine-based hole transporting materials for vacuum-deposited perovskite solar cells
2020
In a short period of time, the rapid development of perovskite solar cells attracted a lot of attention in the science community with the record for power conversion efficiency being broken every year. Despite the fast progress in power conversion efficiency there are still many issues that need to be solved before starting large scale commercial applications, such as, among others, the difficult and costly synthesis and usage of toxic solvents for the deposition of hole transport materials (HTMs). We herein report new enamine-based charge transport materials obtained via a simple one step synthesis procedure, from commercially available precursors and without the use of expensive organomet…
Impurity analyses of silicon wafers from different manufacturing routes and their impact on LID of finished solar cells
2013
Summarizes the measurements of impurity concentrations in directionally solidified silicon ingots from different feedstocks. The substitutional Carbon and interstitial Oxygen are measured on as-sawn wafers using FTIR. Active iron concentration is mapped on a-Si:H passivated wafers. It is observed that these impurities present in Elkem Solar Grade Silicon (ESS™) concentrations are comparable to the standard polysilicon which are in the acceptable ranges for silicon for solar industry. The measured LID of the finished solar cells is also comparable.
Energy level determination in bulk heterojunction systems using photoemission yield spectroscopy: case of P3HT:PCBM
2018
Financial support provided by Scientific Research Project for Students and Young Researchers Nr. SJZ2015/20 realized at the Institute of Solid State Physics, University of Latvia, is greatly acknowledged. This work has been supported by the Latvian State Research Program on Multifunctional Materials IMIS2. Jennifer Mann from Physical Electronics is greatly acknowledged for providing UPS data.
Effects of Frequency Dependence of the External Quantum Efficiency of Perovskite Solar Cells
2018
Perovskite solar cells are known to show very long response time scales, on the order of milliseconds to seconds. This generates considerable doubt over the validity of the measured external quantum efficiency (EQE) and consequently the estimation of the short-circuit current density. We observe a variation as high as 10% in the values of the EQE of perovskite solar cells for different optical chopper frequencies between 10 and 500 Hz, indicating a need to establish well-defined protocols of EQE measurement. We also corroborate these values and obtain new insights regarding the working mechanisms of perovskite solar cells from intensity-modulated photocurrent spectroscopy measurements, iden…
ITO top-electrodes via industrial-scale PLD for efficient buffer-layer-free semitransparent perovskite solar cells
2022
The deposition of transparent conductive oxides (TCO) usually employs harsh conditions that are frequently harmful to soft/organic underlayers. Herein, successful use of an industrial pulsed laser deposition (PLD) tool to directly deposit indium tin oxide (ITO) films on semitransparent vacuum-deposited perovskite solar cells without damage to the device stack is demonstrated. The morphological, electronic, and optical properties of the PLD deposited ITO films are optimized. A direct relation between the PLD chamber pressure and the solar cell performance is obtained. The semitransparent perovskite solar cells prepared exclusively by vacuum-assisted techniques had fill factors of 78% and exc…
Radiative efficiency of lead iodide based perovskite solar cells
2014
The maximum efficiency of any solar cell can be evaluated in terms of its corresponding ability to emit light. We herein determine the important figure of merit of radiative efficiency for Methylammonium Lead Iodide perovskite solar cells and, to put in context, relate it to an organic photovoltaic (OPV) model device. We evaluate the reciprocity relation between electroluminescence and photovoltaic quantum efficiency and conclude that the emission from the perovskite devices is dominated by a sharp band-to-band transition that has a radiative efficiency much higher than that of an average OPV device. As a consequence, the perovskite have the benefit of retaining an open circuit voltage ~0.1…