Search results for " interfaces"
showing 10 items of 1158 documents
Self-assembled three-dimensional inverted photonic crystals on a photonic chip
2017
Three dimensional photonic crystals (PhCs) exhibiting a full photonic band gap have high potential in optical signal processing and detector applications. However, the challenges in the integration of the 3D PhCs into photonic circuits have so far hindered their exploitation in real devices. This article demonstrates the fabrication of 3D PhCs exploiting the capillary directed self-assembly (CDSA) of monodisperse colloidal silica spheres, their inversion to silicon shells, and integration with silicon waveguides. The measured transmission characteristics agree with numerical predictions and provide strong indication of a full photonic band gap in the inverted 3D photonic crystals at wavelen…
Fouling dynamics in suspension flows
2002
A particle suspension flowing in a channel in which fouling layers are allowed to form on the channel walls is investigated by numerical simulation. A two-dimensional phase diagram with at least four different behaviors is constructed. The fouling is modeled by attachment during collision with the deposits and by detachment caused by large enough hydrodynamic drag. For fixed total number of particles and small Reynolds numbers, the relevant parameters governing the fouling dynamics are the solid volume fraction of the suspension and the detachment drag force threshold. Below a critical curve in this 2D phase space only transient fouling takes place when the suspension is accelerated from re…
Calcium phosphate/polyvinyl acetate coatings on SS304 via galvanic co-deposition for orthopedic implant applications
2021
Abstract In this work, the galvanic deposition method is used to deposit coatings of brushite/hydroxyapatite/polyvinyl acetate on 304 stainless steel. Coatings are obtained at different temperatures and with different sacrificial anodes, consisting of a mixture of brushite and hydroxyapatite. Samples are aged in a simulated body fluid (SBF), where a complete conversion of brushite into hydroxyapatite with a simultaneous change in morphology and wettability occurred. The corrosion tests show that, compared with bare 304, the coating shifts Ecorr to anodic values and reduces icorr Ecorr, and icorr has different values at different aging times due to chemical interactions at the solid/liquid i…
Investigation of the porosity of silica and alumina with chemically bonded polystyrene
1996
The effect of modification of porous silica and alumina with a copolymer of styrene and vinylsilane on the porosity of oxides have been investigated by means of low temperature nitrogen sorption. Only small changes of the specific surface area and of the specific pore volume were observed on modification of oxides with non-cross-linked copolymer. The specific surface area significantly increased after the cross-linking of the deposited polymeric layer while the specific pore volume remains almost unaffected. A broad hysteresis loop appears in the nitrogen sorption isotherm for the alumina modified with the cross-linked polymer. The porosity of oxides modified by chemisorption method differe…
Dipoles in 4,12,4-graphyne
2021
Abstract In present work, B-N pairs as dipole source were introduced into 4,12,4-graphyne. According to the density functional theory (DFT) simulations, the electronic configurations of the doped 4,12,4-graphyne systems were significantly modified owing to the built-in electric fields caused by the B-N dipoles. Different B-N concentrations and arrangements can alter the electronic structure of 4,12,4-graphyne. Consequently, an obvious in-plane piezoelectricity can also be induced. Moreover, the direct band gap can be delicately modulated from 150 meV to 660 meV at PBE level. The B-N dipoles can also greatly enhance the light absorption instead of shifting the absorption region. According to…
Curvature radius measurement by optical profiler and determination of the residual stress in thin films
2019
Abstract The Stoney formula, based on the measurement of the substrate curvature, is often used for the determination of the thin films' residual stress. In this study, titanium nitride coatings were deposited by DC reactive magnetron sputtering on silicon substrates. An optical profiler was used to determine the curvature of the surface before and after coating. Two radii were then obtained, along the principal perpendicular directions of the surface curvature. A simple and efficient method to determine the experimental error on the stress calculation was developed taking into account the film thickness dispersion and the radii dispersion. Using constant deposition parameters, some samples…
Mechanical properties and corrosion behaviour after scratch and tribological tests of electrodeposited Co-Mo/TiO2 nano-composite coatings
2019
International audience; The micro-mechanical (Young’s modulus and hardness) and tribological properties, as well as the scratch resistance of Co-Mo/TiO2 nano-composite coatings were investigated. The coating was found to be harder and stiffer than the substrate (pure cobalt). Low residual stresses were also derived from Stoney’s equation (type I stress). The corrosion behaviour after tribological and scratch tests was studied in Ringer’s solution. Dry sliding of the coating against an alumina ball at the load of 1 N or 2 N over the same distance had nearly no influence onthe anodic branch of the polarisation curves. By contrast, the current density in the cathodic branch (oxygen reduction r…
Surface investigation of adhesive formulation consisting of UV sensitive triblock poly(styrene–b-butadiene–b-styrene) copolymer
2002
Abstract Atomic force microscopy (AFM) analysis in conjunction with macroscopic studies such as peel testing and contact angle measurement have been undertaken to explain the nanomechanical properties of adhesive formulation consisting of triblock poly(styrene–b-butadiene–b-styrene) (SBS) copolymers. The cross-linking of this photosensitive copolymer was investigated by analyzing the mechanical and morphological changes of each phase induced by the UV exposure. Main result is that the adhesive properties are strongly influenced by the cross-linking of the polybutadiene (PB) phase leading to an increase in the surface stiffness without affecting the surface energy. AFM analysis shows that th…
X-ray multiple diffraction in the characterization of TiNO and TiO2 thin films grown on Si(001)
2006
Abstract TiO 2 and TiN x O y thin films grown by low pressure metal-organic chemical vapor deposition (LP-MOCVD) on top of Si(0 0 1) substrate were characterized by X-ray multiple diffraction. X-ray reflectivity analysis of TiO 2 [1 1 0] and TiNO[1 0 0] polycrystalline layers allowed to determine the growth rate (−80 A/min) of TiO 2 and (−40 A/min) of TiNO films. X-ray multiple diffraction through the Renninger scans, i.e., ϕ -scans for (0 0 2)Si substrate primary reflection is used as a non-conventional method to obtain the substrate lattice parameter distortion due to the thin film conventional deposition, from where the information on film strain type is obtained.
Combining magnetic field induced locomotion and supramolecular interaction to micromanipulate glass fibers: toward assembly of complex structures at …
2011
The formation of ordered complex structures is one of the most challenging fields in the research of biomimic materials because those structures are promising with respect to improving the physical and mechanical properties of man-made materials. In this letter, we have developed a novel approach to fabricating complex structures on the mesoscale by combining magnetic-field-induced locomotion and supramolecular-interaction-assisted immobilization. We have employed a magnetic field to locomote the glass fiber, which was modified by the layer-by-layer self-assembly of magnetic nanoparticles, to desired positions and have exploited the supramolecular interaction to immobilize glass fiber onto …