Search results for " kinetic"

Matter Transport and Corrosion Kinetics of Metals and Alloys at High Temperature

1992

Electrogeneration of Diiodoaurate in Dimethylsulfoxide on Gold Substrate and Localized Patterning

2016

International audience; A localized etching of gold surface by scanning electrochemical microscope technique is presented where a dimethylsulfoxide-based electrolyte charged with iodine is used. The electrogenerated triiodide ion at the platinum ultramicroelectrode tip (feedback mode) acts as an oxidant for gold surface. The effects of electrode diameter and the bias time have been investigated. The approach curve method was used to hold the electrode tip close to the gold surface. A scanning electron microscope is used to observe the etched gold surfaces where disk-shaped dots are generated. The diameter of these holes depends directly on the Pt electrode diameter and the bias time.

Hygrothermal ageing of reprocessed polylactide

2012

[EN] The influence of an accelerated hygrothermal ageing simulation test on a commercial PLA and its three subsequent mechanically-reprocessed materials was studied. The analysis was focused on the water diffusion kinetics and the physico-chemical changes induced by the hygrothermal degradation. Water diffusion proceeded faster than chain relaxation processes, as defined by a Case II absorption model. It was proved that the water diffusion rate decreased with subsequent reprocessing cycles and increased with higher hygrothermal ageing temperatures. Hydrolytic chain scission provoked significant molar mass decays and consequent general losses of thermal and mechanical performance. The rearra…

Anodization and anodic oxides

2018

Anodizing is a low-temperature, low-cost electrochemical process allowing for the growth, on the surface of valve metals and valve metal alloys, of anodic oxides of tunable composition and properties. This article is an overview on theoretical aspects concerning the general aspects of the kinetics of growth of barrier and porous anodic oxides and some of their present and possibly future technological applications of anodic oxides. The first part of the article is devoted to anodic oxide growth models, from Guntherschulze and Betz work (in 1934) to the more recent results on barrier and porous oxide films. The second part is focused on industrial processes to fabricate anodic oxides and the…

Crystallization kinetics of colloidal model suspensions: recent achievements and new perspectives

2014

Colloidal model systems allow studying crystallization kinetics under fairly ideal conditions with rather well characterized pair interactions and minimized external influences. In complementary approaches therefore experiment, analytic theory and simulation have been employed to study colloidal solidification in great detail. These studies were based on advanced optical methods, careful system characterization and sophisticated numerical methods. Both the effects of the type, strength and range of the pair-interaction between the colloidal particles and those of the colloid-specific polydispersity were addressed in a quantitative way. Key parameters of crystallization were derived and comp…

Thermomechanical properties and thermal degradation kinetics of poly(methyl methacrylate) (PMMA) and polycarbonate (PC) filled with cerium-doped yttr…

2016

This paper reports on the thermomechanical properties and thermal degradation kinetics of poly(methyl methacrylate) (PMMA) and polycarbonate (PC) composites filled with cerium-doped yttrium aluminium garnet (Ce:YAG) at different contents ranging between 0.1 and 5 wt%, and prepared by melt compounding. The interaction between PMMA and the filler was much stronger than that between PC and the filler, and this resulted in a significant improvement in the dynamic mechanical properties of the PMMA composites. The presence of filler did not significantly increase the thermal stability of the PC, while an observable increase in the thermal stability was only observed at higher filler loadings for …

Development and In Vitro Evaluation of Lyotropic Liquid Crystals for the Controlled Release of Dexamethasone.

2017

Made available in DSpace on 2018-12-11T17:33:26Z (GMT). No. of bitstreams: 0 Previous issue date: 2017-08-02 Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) In this study, amphiphilic polymers were investigated as biomaterials that can control dexamethasone (DXM) release. Such materials present interfacial properties in the presence of water and an oily phase that can result in lyotropic liquid crystalline systems (LLCS). In addition, they can form colloidal nanostructures similar to those in living organisms, such as bilayers and hexagonal and cubic phases, which can be exploited to solubilize lipophilic drugs to sustain their release and enhance bioavailability. It was…

The rate of polymerization in two loci reaction systems: VDF-HFP precipitation copolymerization in supercritical carbon dioxide

2011

When the copolymerization of vinylidene fluoride (VDF) and hexafluoropropylene (HFP) is carried out in supercritical carbon dioxide (scCO 2) under heterogeneous conditions, the reaction occurs both in the continuous CO 2-rich phase and in the dispersed polymer-rich phase. The two phases being characterized by different values of reactant concentrations and kinetic parameters, one would expect that the reaction kinetics is affected by the polymer phase holdup in the reactor. However, the reaction rate is almost insensitive to the amount of produced polymer, at least at specific reaction conditions. This apparent contradiction is discussed and clarified in this paper by a series of comparativ…

Polybutadiene model networks —synthesis, mechanical characterization and comparison with rubber elasticity models

1995

Model networks of defined crosslink density are prepared via nonradical statistical crosslinking of polybutadiene in bulk and concentrated solution using a masked bistriazolinedione as crosslinker. The kinetics of crosslinking is monitored by FT-IR-spectroscopy. The reaction follows pseudo-1st-order reaction kinetics. The activation parameter of the crosslinking reaction is estimated from crosslinking at various temperatures. Networks of deuterated polybutadiene are prepared by this reaction in a wide range of crosslink densities. The stress strain behavior is analyzed according to the Junction Constraint-Theory of rubber elasticity (JCT) and to the approach introduced by Graessley accounti…

A one-pot method to enhance dissolution rate of low solubility drug molecules using dispersion polymerization in supercritical carbon dioxide

2009

The surfactant assisted polymerization of 1-vinyl-2-pyrrolidone in supercritical carbon dioxide in the presence of Piroxicam, selected as a model of a low aqueous solubility drug, was studied in order to prepare in a single step a polymeric composite to enhance the rate of dissolution of the pharmaceutical compound. Reactive entrapping was carried out at 65 degrees C in the P range 21-38MPa. Under proper operative conditions we obtained the composite under the form of sub-micron spherical particles with relatively narrow particle size distribution. Drug loadings higher than 12% (w/w) were obtained and XRD and Raman spectroscopy suggest that the anti-inflammatory agent is dispersed in the ma…