Search results for " motore"
showing 10 items of 87 documents
In vitro validation of biomedical polyester-based scaffolds: Poly(lactide-co-glycolide) as model-case
2018
[EN] Monitoring and understanding the in vitro behaviour of polyester based scaffolds both comprising the study of the hydrolytic degradation and the cell seeding viability is essential to ensure the desired functionality, according to a given biomedical purpose. As a model case to compare the performance of techniques to monitor the in vitro behaviour, poly(lactide-co-glycolide) (PLGA) scaffolds were chosen. The in vitro hydrolytic degradation of PLGA scaffolds was carried out in water and phosphate buffered saline (PBS). The evolution of the mass loss, the molar mass, the thermal properties and the surface morphology were monitored. The hydrolytic degradation media was correspondingly eva…
An Experimental Study of In-Cylinder Heat Transfer from a Pressurized Motored Engine with Varying Peak Bulk Gas Temperatures
2022
The variation of in-cylinder heat transfer with parameters such as engine speed, air-to-fuel ratio, coolant temperature and compression ratio were frequently studied in classical research. These experimentally-obtained relationships are important for improving in-cylinder heat transfer models, essential in developing CO2 reducing strategies. In this publication, a 2.0 liter compression ignition engine was tested in the pressurized motored configuration. This developed experimental setup allowed testing of the engine at speeds ranging between 1400 rpm and 3000 rpm, with peak in-cylinder gas pressures from 40 bar to 100 bar. The engine was motored using different gas compositions chosen speci…
Modello dinamico di iniettore di gas per motore ad accensione comandata
2010
Nel presente lavoro si studia la complessa dinamica dell’otturatore di un iniettore di gas a solenoide per motori ad accensione comandata; come è noto, esso è sottoposto a spinte di diversa natura ed il suo moto ha un influenza determinante nei confronti della massa di combustibile erogata, la quale viene di norma modulata intervenendo sulla durata dell’intervallo di eccitazione del solenoide, chiamato “tempo di iniezione”. Ad otturatore completamente aperto, la massa di gas che attraversa la sezione di uscita dell’iniettore dipende esclusivamente dalle condizioni del fluido a monte dell’iniettore e dalla durata del tempo di iniezione: ciò rende lineare la caratteristica di funzionamento de…
Energia da gradienti salini: dall’acqua l’energia del futuro
2017
Today, continuous research efforts are aimed at finding alternative renewable energy sources to conventional ones and efficient technologies able to exploit them. Saline gradient energy is an unconventional renewable energy source widely available and currently under-exploited. In the present document the most technologies are illustrated avant-garde for the conversion of this energy into electric current: Pressure Retarded Osmosis, PRO (Osmosis Delayed by Pressure) and the Reverse Electrodialysis, RED (Inverse Electrodialysis).
Novel silicon microparticles to improve sunlight stability of raw polypropylene
2015
Oxidation of polyolefins by ultraviolet/visible irradiation is a significant limitation for their use in several technological applications. The use of high-tech additives such as silicon microparticles becomes a compositing strategy that can improve the performance of these materials at long-term service conditions. Silicon particles were added to non-additivated raw polypropylene (PP) prepared by hot melt extrusion and subjected to accelerated sunlight irradiation tests. The stability of thermal properties, mechanical performance and thermal decomposition behaviour of composites was evaluated by differential scanning calorimetry, dynamic mechanical thermal analysis and thermogravimetry. T…
A statistical design of experiments for optimizing the MALDI-TOF-MS sample preparation of polymers. An application in the assessment of the thermo-me…
2011
[EN] The sample preparation procedure for MALDI-TOF MS of polymers is addressed in this study by the application of a statistical Design of Experiments (DoE). Industrial poly (ethylene terephthalate) (PET) was chosen as model polymer. Different experimental settings (levels) for matrixes, analyte/matrix proportions and concentrations of cationization agent were considered. The quality parameters used for the analysis were signal-to-noise ratio and resolution. A closer inspection of the statistical results provided the study not only with the best combination of factors for the MALDI sample preparation, but also with a better understanding of the influence of the different factors, individua…
Triblock SEBS/DVB crosslinked and sulfonated membranes: Fuel cell performance and conductivity
2021
[EN] A set of styrene-ethylene-butylene-styrene triblock copolymer (SEBS) membranes with 10 or 25 wt.% divinyl-benzene (DVB) as a crosslinking agent were prepared and validated. Physicochemical characterization revealed suitable hydrolytic and thermal stability of photo-crosslinked membranes containing 25%wt. DVB and post-sulfonated. These compositions were evaluated in H2/O2 single cells, and electrical and proton conductivities were furtherly assessed. The membranes with the milder post-sulfonation showed greater proton conductivity than those with excessive sulfonation. In terms of electrical conductivity, a universal power law was applied, and the values obtained were low enough for bei…
Effect of the dissolution time into an acid hydrolytic solvent to tailor electrospun nanofibrous polycaprolactone scaffolds
2017
[EN] The hydrolysis of the polycaprolactone (PCL) as a function of the dissolution time in a formic/acetic acid mixture was considered as a method for tailoring the morphology of nanofibrous PCL scaffolds. Hence the aim of this research was to establish a correlation between the dissolution time of the polymer in the acid solvent with the physicochemical properties of the electrospun nanofibrous scaffolds and their further service life behaviour. The physico-chemical properties of the scaffolds were assessed in terms of fibre morphology molar mass and thermal behaviour. A reduction of the molar mass and the lamellar thickness as well as an increase of the crystallinity degree were observed …
Influence of substrate and temperature on the biodegradation of polyester-based materials: Polylactide and poly(3-hydroxybutyrate-co-3-hydroxyhexanoa…
2020
[EN] The extended use of polymers from renewable resources such as aliphatic polyesters or polyhydroxyalkanoates boosted the necessity to understand their behaviour in an end-of-life scenario. Although they can be degraded in reasonable shorter times than traditional polymers, understanding the degradation mechanisms under dissimilar conditions will contribute to further developments in this field. This work aimed to study the effect of temperature and substrate in the degradation of polylactide (PLA) and poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) in a simulated laboratory scale to ascertain their contribution, separately or in combination. For this purpose, nine parallel degradat…
Poly (lactic acid)/D-limonene/ZnO bio-nanocomposites with antimicrobial properties
2022
[EN] Antimicrobial films of poly (lactic acid) (PLA)/D-limonene/zinc oxide (ZnO)-based bio-nanocomposites were prepared via melt compounding and subsequent thermocompression. D-limonene was incorporated at concentrations of 10 or 20 wt%, and ZnO pure nanoparticles and those organically modified with oleic acid (O-ZnO), with an average diameter of 13.5 nm, were included at concentrations of 3, 5, and 8 wt%. The plasticizing effect of D-Limonene was corroborated by a decrease in the glass transition temperature compared to pure PLA. The presence of ZnO and O-ZnO in the PLA matrix promoted a slight increase in the degree of crystallinity due to its nucleant performance. Although ZnO and O-ZnO …