Search results for " oxides"
showing 10 items of 166 documents
Pulsed Direct liquid Injection ALD of TiO2 Films Using Titanium Tetraisopropoxide Precursor
2013
Abstract TiO 2 thin films are grown by pulsed direct liquid injection atomic layer deposition with rapid thermal heating using titanium tetraisopropoxide and water vapor as precursors. The ALD growth rate is constant in the saturation zone range 35-47 ms at the temperature deposition of 280 °C. The TiO 2 growth rate of 0.018 nm/cycle was achieved in a self-limited ALD mode. SEM and AFM analysis showed the as-deposited films have a smooth surface with a low roughness. XPS analysis exhibited the stoichiometry of TiO 2 in the homogenous depth composition.
Co-precipitation synthesis of neodymium-doped yttrium aluminium oxides nanopowders: Quantitative phase investigation as a function of joint isotherma…
2007
Abstract Neodymium-doped yttrium aluminium nanopowders with nominal Nd:Y:Al ratio equal to X:3–X:5 (where X = 0, 0.006, 0.012, 0.024, 0.048, 0.081, 0.096, 0.171, 0.192, 0.384, 0.540 and 0.720) were prepared by the co-precipitation method and subjected to five cumulative stages of isothermal treatment in the temperature range from 900 to 1050 °C. The phase evolution of the oxides were investigated quantitatively by the X-ray powder diffraction approach using the Rietveld method of analysis. An almost single phase cubic garnet structure was attained at temperatures as low as 900 °C for specimens with neodymium loading less than ca. 6 at.% with respect to total (Nd + Y) atoms. Isothermal treat…
XPS and SIMS study of aluminium native oxide modifications induced by Q-switched Nd:YAG laser treatment
2006
Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface Analysis, 25-30 September 2005, Vienna, Austria; International audience; During laser cleaning of aluminium in ambient atmosphere, modifications of the metal surface can be induced by transient thermal effects. This work aims to characterize the modification of the aluminium oxide layer on pure aluminium for a wide range of power per area using a Q-switched Nd :YAG (1064 nm) laser with two pulse durations, 10 and 180 ns. Experiments were carried out with single laser shots in ambient air at fluences (e.g. energy per area) below the ablation regime. For 10-ns pulses with fluences between 0.7 and…
Microstructural and tribological study of Nd:YAG laser treated titanium plates.
2008
Abstract In this work, the fretting behaviour of pure Ti plates laser treated with a Nd:YAG pulsed laser was compared to that of untreated Ti plates. Fretting tests were done at room temperature without lubrication. The contact geometry was a cylinder (bearing steel) on a plane. The evolution of both the ratio, μ = Q / P , between the normal and the tangential forces, and the Fouvry's energy criterion ( A ) were recorded as a function of the number of fretting cycles, N . Energy dispersive spectrometry and micro-Raman spectroscopy were used to analyse the fretting scars. The oxidized layer formed by the laser treatment displayed a mixed slip regime as a function of N , and a smaller frettin…
On the attribution of contributions of atmospheric trace gases to emissions in atmospheric model applications
2010
Abstract. We present an improved tagging method, which describes the combined effect of emissions of various species from individual emission categories, e.g. the impact of both, nitrogen oxides and non-methane hydrocarbon emissions on ozone. This method is applied to two simplified chemistry schemes, which represent the main characteristics of atmospheric ozone chemistry. Analytical solutions are presented for this tagging approach. In the past, besides tagging approaches, sensitivity methods were used, which estimate the contributions from individual sources based on differences in two simulations, a base case and a simulation with a perturbation in the respective emission category. We ap…
Denitrification in pathogenic bacteria : for better or worst ?
2005
A large variety of physiological and taxonomic groups have the ability to use nitrogen oxides as alternative electron acceptors. Brucella spp. is an alpha-proteobacteriaceae that induces a persistent disease in some mammals. Recent work has revealed that a denitrifying gene cluster is important in the interaction of Brucella neotomoae with its host.
Unveiling the Different Chemical Reactivity of Diphenyl Nitrilimine and Phenyl Nitrile Oxide in [3+2] Cycloaddition Reactions with (R)-Carvone throug…
2020
The [3+2] cycloaddition (32CA) reactions of diphenyl nitrilimine and phenyl nitrile oxide with (R)-carvone have been studied within the Molecular Electron Density Theory (MEDT). Electron localisation function (ELF) analysis of these three-atom-components (TACs) permits its characterisation as carbenoid and zwitterionic TACs, thus having a different reactivity. The analysis of the conceptual Density Functional Theory (DFT) indices accounts for the very low polar character of these 32CA reactions, while analysis of the DFT energies accounts for the opposite chemoselectivity experimentally observed. Topological analysis of the ELF along the single bond formation makes it possible to characteri…
A Molecular Electron Density Theory Study of the Chemoselectivity, Regioselectivity, and Diastereofacial Selectivity in the Synthesis of an Anticance…
2019
The [3 + 2] cycloaddition (32CA) reaction of an &alpha
Nanostructuring thin Au films on transparent conductive oxide substrates
2013
Fabrication processes of Au nanostructures on indium-tin-oxide (ITO) surface by simple, versatile, and low-cost bottom-up methodologies are investigated in this work. A first methodology exploits the patterning effects induced by nanosecond laser irradiations on thin Au films deposited on ITO surface. We show that after the laser irradiations, the Au film break-up into nanoclusters whose mean size and surface density are tunable by the laser fluence. A second methodology exploits, instead, the patterning effects of standard furnace thermal processes on the Au film deposited on the ITO. We observe, in this case, a peculiar shape evolution from pre-formed nanoclusters during the Au deposition…
Application of 2D Non-Graphene Materials and 2D Oxide Nanostructures for Biosensing Technology
2016
The discovery of graphene and its unique properties has inspired researchers to try to invent other two-dimensional (2D) materials. After considerable research effort, a distinct "beyond graphene" domain has been established, comprising the library of non-graphene 2D materials. It is significant that some 2D non-graphene materials possess solid advantages over their predecessor, such as having a direct band gap, and therefore are highly promising for a number of applications. These applications are not limited to nano- and opto-electronics, but have a strong potential in biosensing technologies, as one example. However, since most of the 2D non-graphene materials have been newly discovered,…