Search results for " resin"
showing 10 items of 268 documents
Acoustic Emission Monitoring of Chemically Bonded Anchors
2010
This paper presents a study on the use of acoustic emission (AE) to assess the structural soundness of concrete reinforced with chemically bonded anchors. The results of an experimental work based on six pullout tests monitored using an AE instrumentation suite are reported below. In every test one rebar was embedded in the hardened concrete by means of polyester resin. The AE was adopted to moni- tor the onset and progression of any structural damage. The parametric analysis, the intensity analysis and the moment tensor analysis of AE data were used to discriminate among different sources of damage. The technique shows promise for field application and may contribute to fully understand th…
Effects of Moisture and Stresses on the Structure and Properties of Polyester Resin
2004
The results of a complex study of structural changes in a cured Norpol 440 polyester resin under the action of damp environment and mechanical loading are presented. A considerable effect of absorbed moisture on the structure and some characteristics of the material is revealed by using thermophysical methods and X-ray diffractometry. The joint effect of moisture and mechanical stress is estimated by investigating the creep in stationary and nonstationary moisture conditions. The anisotropy of the material structure formed during creep is evaluated from the results of dilatometric measurements. It is found that the degree of anisotropy of the material after creep accompanied by moisture sor…
An investigation of the influence of the macroscopic heterogeneity on the thermoelstic response of fibre reinforced plastics
2005
In this work the influence of the inherent heterogeneity in fibre reinforced plastic composites on the qualitative and quantitative evaluation of the thermoelastic signal is discussed. The role of two different levels of heterogeneity is identified, distinguishing between a micro-geometric scale characterized by the presence of different constituent materials, and a macro-geometric scale characterized by a non-uniform distribution of these constituents. Attention has been focused on the macro-scale level, presenting results of experiments performed on glass fibre - polyester resin samples, intended to highlight the influence on the thermoelastic signal of the fabric texture pattern and the …
α-Chymotrypsin-Catalyzed Reaction Confined in Block-Copolymer Vesicles
2010
Herein the reactivity of the enzyme α-chymotrypsin in the confinement of polystyrene-block-poly(acrylic acid) (PS-b-PAA) vesicles was investigated. Enzyme and substrate molecules were encapsulated in PS-b-PAA vesicles with internal diameters ranging from 26 nm to 165 nm during the formation of the vesicles. While the loading efficiencies of enzyme and substrate molecules were practically identical for vesicles of identical size, they were found to increase with decreasing vesicle size. The kinetics of the α-chymotrypsin catalyzed hydrolysis of N-succinyl-Ala-Ala-Phe-7-amido-4-methylcoumarin (AMC) was evaluated following the increase of the absorption of the product 7-amino-4-methylcoumarin …
Stiffness and strength of flax fiber/polymer matrix composites
2006
Flax fiber composites with thermoset and thermoplastic polymer matrices have been manufactured and tested for stiffness and strength under uniaxial tension. Flax/polypropylene and flax/maleic anhydride grafted polypropylene composites are produced from compound obtained by coextrusion of granulated polypropylene and flax fibers, while flax fiber mat/vinylester and modified acrylic resin composites are manufactured by resin transfer molding. The applicability of rule-of-mixtures and orientational averaging based models, developed for short fiber composites, to flax reinforced polymers is considered. POLYM. COMPOS. 27:221–229, 2006. © 2006 Society of Plastics Engineers
The effect of dentine pre-treatment using bioglass and/or polyacrylic acid on the interfacial characteristics of resin-modified glass ionomer cements.
2018
Objective To evaluate the effect of load-cycle aging and/or 6 months artificial saliva (AS) storage on bond durability and interfacial ultramorphology of resin-modified glass ionomer cement (RMGIC) applied to dentine air-abraded using Bioglass 45S5 (BAG) with/without polyacrylic acid (PAA) conditioning.Methods RMGIC (Ionolux, VOCO) was applied onto human dentine specimens prepared with silicon-carbide abrasive paper or air-abraded with BAG with or without the use of PAA conditioning. Half of bonded-teeth were submitted to load cycling (150,000 cycles) and half immersed in deionised water for 24 h. They were cut into matchsticks and submitted immediately to microtensile bond strength (μTBS) …
Cytotoxicity and induction of DNA double-strand breaks by components leached from dental composites in primary human gingival fibroblasts
2012
Abstract Introduction The public interest steadily increases in the biological adverse effects caused by components released from resin-based dental restorations. Objective In this study, the cytotoxicity and the genotoxicity were investigated of following released components from dental resin restorations in human gingival fibroblasts (HGF): tetraethyleneglycol dimethacrylate (TEEGDMA), neopentylglycol dimethacrylate (Neopen), diphenyliodoniumchloride (DPIC), triphenyl-stibane (TPSB) and triphenylphosphane (TPP). Methods XTT based cell viability assay was used for cytotoxicity screening of substances. γ-H2AX assay was used for genotoxicity screening. In the γ-H2AX assay, HGFs were exposed …
Novel epoxy formulations for high energy radiation curable composites
2005
Abstract It has been widely recognised that high energy radiation can be effectively applied to the cure of epoxy resins in applications as composite matrices or structural adhesives with improvements in product quality and/or reduction in production costs. In the presence of suitable initiators, polymerisation of epoxies occurs via cationic mechanism, thus restricting the choice of the resin system components to species which do not contain electron donor groups. The present investigation is aimed to identify suitable co-monomers to be formulated with an epoxy resin, resulting in different cure reaction kinetics and application properties of the cured resin. In particular, four different a…
Structural investigation of e-beam cured epoxy resins through solid state NMR
2012
Abstract In this paper the network structure of e-beam cured DGEBF based epoxy resins is investigated. Two epoxy systems, having different reactivity and cured in different process conditions, were analyzed through solid state NMR spectroscopy. The analysis shows that the more reactive system has higher cross-linking density and higher uniformity of network distribution. Similar information were obtained, in a previous work, on the same systems through dynamic mechanical thermal analysis. It is worth noting that unlike DMTA tests, which interfere with the molecular structure of the analyzed material, due to the heating during the analysis itself, more reliable information, without any artef…
Radiation curing of carbon fibre composites
2014
Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric. Dynamic mechanical thermal analysis was carried out in order to determine the cross-linking degree. The analysis pointed out a nonuniformity in the cross-linking degree of the e-beam cured panels, with the formation of clusters at low Tg (glass transition temperature) and clusters at high Tg. An out-of-mould post irradiation thermal treatment on e-beam cured samples provides…