Search results for "8"
showing 10 items of 46225 documents
Silicon dosimeters based on Floating Gate Sensor: design, implementation and characterization
2020
A rad-hard monolithic dosimeter has been implemented and characterized in a standard 180 nm CMOS technology. The radiation sensor (C-sensor) is based on a Floating Gate (FG) MOS discharge principle. The output current is processed by a current-to-voltage (I/V) interface and then converted by a 5-bit flash ADC. The dosimeter is re-usable (FG can be recharged) and can detect a dose up to 1krad (Si) with a resolution of 30rad (Si) typical over temperature 0 to 85°C range. The ADC allows easy further signal processing for calibration and averaging, etc. The power consumption of C-sensor plus I/V interface is < 2mW from a 5 V power supply. The overall layout area is less than 0.25mm2. The Rad…
Data-driven Fault Diagnosis of Induction Motors Using a Stacked Autoencoder Network
2019
Current signatures from an induction motor are normally used to detect anomalies in the condition of the motor based on signal processing techniques. However, false alarms might occur if using signal processing analysis alone since missing frequencies associated with faults in spectral analyses does not guarantee that a motor is fully healthy. To enhance fault diagnosis performance, this paper proposes a machinelearning based method using in-built motor currents to detect common faults in induction motors, namely inter-turn stator winding-, bearing- and broken rotor bar faults. This approach utilizes single-phase current data, being pre-processed using Welch’s method for spectral density es…
Low complexity digital background calibration algorithm for the correction of timing mismatch in time-interleaved ADCs
2019
Abstract A low-complexity post-processing algorithm to estimate and compensate for timing skew error in a four-channel time-interleaved analog to digital converter (TIADC) is presented in this paper, together with its hardware implementation. The Lagrange interpolator is used as the reconstruction filter which alleviates online interpolator redesign by using a simplified representation of coefficients. Simulation results show that the proposed algorithm can suppress error tones for input signal frequency from 0 to 0.4 f s . The proposed structure has, at least, 41% reduction in the number of required multipliers. Implementation of the algorithm, for a four-channel 10-bit TIADC, show that, f…
Space‐vector state dynamic model of SynRM considering self‐ and cross‐saturation and related parameter identification
2020
This study proposes a state formulation of the space-vector dynamic model of the Synchronous Reluctance Motor (SynRM) considering both saturation and cross-saturation effects. The proposed model adopts the stator currents as state variables and has been theoretically developed in both the rotor and stator reference frames. The proposed magnetic model is based on a flux versus current approach and relies on the knowledge of 11 parameters. Starting from the definition of a suitable co-energy variation function, new flux versus current functions have been initially developed, based on the hyperbolic functions and, consequently, the static and dynamic inductance versus current functions have be…
Metrological Properties of the Test Setup for Determination Shielding Effectiveness of the Industrial Cable Connectors
2017
Abstract The paper presents results related to assessment of the repeatability and reproducibility of the measurement test setup for determination the relative value of the shielding effectiveness coefficient of the industrial connectors. The construction of the proposed test setup, the measurement method and the procedure for the analysis of measurement results were described. To determine the value of the repeatability and reproducibility coefficient, the two–way analysis of variance was used, which additionally allows for an assessment of the influence of individual sources of variance. The measurements and their analysis were conducted for several frequencies in the range up to 1 GHz. A…
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
Computer-aided analysis and design procedure for rotating induction machine magnetic circuits and windings
2018
The aim of this study is to present a new, accurate, and user-friendly software procedure for the analysis and rapid design of rotating induction machine windings, considering both the electric and the magnetic specifications of the machine itself. This procedure is a valid aid for quick first stage design without the necessity of using finite element method (FEM)-based design procedures. FEM can be used in a second design phase in order to refine the first stage results. The design procedure is hereafter outlined and some examples show its capability.