Search results for "ALLOYS"
showing 10 items of 1689 documents
Halloysite nanotubes-based nanocomposites for the hydrophobization of hydraulic mortar
2021
Abstract The treatment of stone surfaces for their protection from ageing caused by natural and anthropogenic effects is an open issue in materials development for Cultural Heritage. We thought interesting to verify the suitability of a modified cellulose biofilm filled with halloysite nanotubes as wax compatibilizers to design a protecting layer. A hydraulic mortar was selected as a stone prototype. To improve the physico-chemical properties of the covering layer, wax microparticles have been incorporated to control transport, consolidation and wettability features. In particular, different application protocols have been studied, namely brushing and spraying, to assess whether the propos…
Laser Cladding of TiC for Better Titanium Components
2011
Pure commercial titanium is widely used because of its high corrosion resistance and lower cost compared with other titanium alloys, in particular when there is no high wear requirements. Nevertheless, the wear resistance is poor and surface damage usually occurs in areas under contact loadings. Laser cladding is a suitable technique for manufacturing precise and defect free coatings of a dissimilar material with higher wear and corrosion resistance. In this work a good understanding of laser metal deposition mechanisms allowed to obtain defect free coatings of Ti6Al4V and TiC metal matrix composite (MMC) using a flash lamp pumped Nd:YAG laser of 1 kW. A complete investigation of the proces…
Total ionizing dose (TID) evaluation of magnetic tunnel junction (MTJ) current sensors
2015
Abstract The paper shows an experimental study to know the behaviour of tunnel magnetoresistive effect-based current sensors configured in a Wheatstone bridge in response to irradiation. In particular the sensitivity, hysteresis, output offset voltage and input resistance are discussed when the sensors are submitted to a total irradiation dose of 43 krad with 36 krad/h dose rate. The same electrical parameters were studied subsequently once the irradiated sensors were submitted to an 80 °C annealing process. The studied TMR sensors are applied in a switched-mode power converter for space application.
Spray pyrolysis synthesis and characterization of Mg1-xSrxMoO4 heterostructure with white light emission
2020
[EN] Molybdates are inorganic materials with great potential in white phosphors application, being an alternative to traditional lighting sources. In this study, we report the synthesis and characterization of Mg1-xSrxMoO4 (x = 0, 0.25, 0.50, 0.75, and 1) powders with white light-emitting properties. Using X-ray diffraction, the formation of the monoclinic beta-MgMoO4 phase was observed for x = 0 and the formation of the tetragonal scheelite phase of SrMoO4 was observed for x = 1. The formation of a heterostructure composed of both phases was found for compositions with x = 0.25, 0.50 and 0.75. Scanning and trasmission electron microscopy images showed that the Mg1-xSrxMoO4 particles exhibi…
On the FE codes capability for tool temperature calculation in machining processes
2006
Abstract The applications of numerical simulation to machining processes have been more and more growing in the last years: today a quite effective predictive capability has been reached, at least as far as global cutting variables (for instance cutting forces) are concerned. On the other hand, the capability to predict local cutting variables (i.e. pressure on the tool, temperature distribution, residual stresses in the machined surface) has to be heavily improved and verified. At the same time, effective experimental procedures for validating numerical results have to be developed. In this work two different approaches were implemented for temperature measuring: a thermocouple based appro…
On the mechanisms involved in the tensile strength of a dissimilar Ti6Al4V/316L laser welded assembly
2021
International audience; The aim of the present work is to analyze the thermomechanical behavior of dissimilar laser seams by means of FE modeling. The case of a Ti6Al4V/316L assembly with vanadium insert was considered. Effective mechanical properties of the main materials and cords were first estimated from NHT measurements. Modeling of the double pass laser welding process was performed first by considering shrinking of the two weld seams during manufacturing, to get the residual stress state in the welded assembly. Modeling of the tensile test was performed in a second step to study the assembly behavior during loading. In these modeling results, the mesh was the cross-section of the mic…
On the improvement of material formability in SPIF operation through tool stirring action
2012
Single-point incremental forming (SPIF) is a quite new sheet-forming process which offers the possibility to deform complex parts without dedicated dies using a single-point tool and a standard three-axis CNC machine. The process mechanics enables higher strains with respect to traditional sheet-forming processes, but particular attention must be given to the maximum forming angle. In this paper, a new approach is proposed to enhance the material formability through a localized sheet heating as a consequence of the friction work caused by elevated tool rotational speeds. AA1050-O, AA1050-H24, and AA6082-T6 were utilized, and the reached temperatures were recorded by thermocouples, fixed to …
Effect of mechanical stirring and temperature on dynamic hydrothermal synthesis of titanate nanotubes
2017
Abstract In the late century, it has been clearly demonstrated that titanate nanotubes (TNTs) are attractive nanomaterials with various potential applications due to their interesting properties. In this work, an essential reaction parameter, rarely considered in the literature, has been studied: stirring during hydrothermal synthesis. For this purpose, an intermittent mechanical stirring, ranging from 0 to 20 min/h, has been applied during the TNTs synthesis using a new dynamic hydrothermal reactor. It was proved that a long stirring cycle (more than 10 min/h) at 150 °C and an overall reaction time of 16 h promotes nanoribbons synthesis instead of nanotubes. In this context, a detailed mor…
Microwave-based gas sensor with phthalocyanine film at room temperature
2013
Abstract This work presents the development of a microwave gas sensor at room temperature. The design of the sensor includes a coplanar grounded wave guide where is deposited a molecular gas sensing material. In this study, the sensitive material is a thin layer of cobalt phthalocyanine (CoPc), sensitive to ammonia and toluene. Submitted to an electromagnetic incident wave in the microwave range, the sensor response is a reflected wave. In the presence of pollutant, the reflected wave shape is specific to the species concentrations. The results interpretation is led at each frequency by the evaluation of the reflected coefficient, which traduces the ratio between the reflected wave over the…
Numerical study of photolithography system: electromagnetic differential method
2004
The R-matrix propagation algorithm is incorporated into the differential method to achieve an extended capability for modelling a photolithography systems. We show throughout this work the ability of the R-matrix algorithm and differential method to analyse gratings of arbitrary depth, profile, and conductivity without encountering numerical instabilities. We calculate the field intensity and the transmitted amplitudes in the 0 and −1 orders below different masks. We study also the influence of the various parameters (incidence, groove spacing, groove depth and index of refraction) on the field intensity maps and the transmittivity power. These results agree with the experimental patent: we…