Search results for "Amorphous solid"
showing 10 items of 622 documents
ChemInform Abstract: In situ DRIFT Spectroscopic Investigation on the Chemical Evolution of Zinc Phosphate Acid-Base Cement.
2010
Diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy has been used to follow the chemical evolution of zinc phosphate acid−base cement (ZPC), which has been prepared from unmodified, as well as from aluminum- and zinc-modified orthophosphoric acid. For the first time, amorphous dizinc cyclotetraphosphate octahydrate, Zn2P4O12·8H2O, although hydrolytically instable, has been observed as precursor phase prior to crystallization of α-hopeite, α-Zn3(PO4)2·4H2O, in both systems. Within minutes from onset of mixing the infrared spectrum of unmodified ZPC is dominated by the characteristic vibrations of α-hopeite, due to matrix crystallization. Setting of modified ZPC is strongly af…
The effect of silica nanoparticles on the morphology, mechanical properties and thermal degradation kinetics of PMMA
2012
Abstract Silica–PMMA nanocomposites with different silica quantities were prepared by a melt compounding method. The effect of silica amount, in the range 1–5 wt.%, on the morphology, mechanical properties and thermal degradation kinetics of PMMA was investigated by means of transmission electron microscopy (TEM), X-ray diffractometry (XRD), dynamic mechanical analysis (DMA), thermogravimetric analyses (TGA), Fourier-transform infrared spectroscopy (FTIR), 13 C cross-polarization magic-angle spinning nuclear magnetic resonance spectroscopy ( 13 C{ 1 H} CP-MAS NMR) and measures of proton spin-lattice relaxation time in the rotating frame ( T 1 ρ ( H )), in the laboratory frame ( T 1 ( H )) a…
Deformation recovery behavior of a solid polymer after tensile yielding
1984
In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3).
Deformation recovery behaviour of a solid polymer after tensile yielding
1987
In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3). The data here presented indicate that the influence of all parameters, including temperature, on recovery behavior can be related to the residual stress, σ *, at the beginning of recovery test. This suggests to plot the recovery versus time curves, relative to different sets of parameters including temperature, by means of the same normalizing groups which were adopted in (2), thus shifting all curves towards a single master curve.
Photoelectrical properties of indandione fragment containing azobenzene compounds
2014
Organic materials are becoming more popular due to their potential application in electronics. Low molecular weight materials possible produce from solution are in special consideration. It gives the possibility to avoid both thermal evaporation in vacuum, and use of polymers in thin film preparation process. Indandione fragment containing azobenzene compounds are one of such materials. These compounds are good candidates for use in design of novel molecular electronic devices due to their possibility to form amorphous structure from solution thus allowing developing flexible, small size systems with low production costs. In this work three indandione fragment containing azobenzene compound…
RELAXATION METHODS FOR STUDYING MACROMOLECULAR MOTION IN THE BULK
1982
Abstract Macromolecular motion in amorphous and partially crystalline polymers is discussed in the light of recent relaxation experiments with particular emphasis on NMR methods. Polystyrene and polyethylene serve as pertinent examples where a considerable amount of new experimental data provides a bysis for better understanding molecular processes below and above the glass transition, and in the melt.
Thermal and optical properties of 4H-pyran-4-ylidene fragment and bis-styryl and triphenyl groups containing derivatives
2014
Small D-π-A type organic molecules with incorporated 4H-pyan-4-ylidene (pyranylidene) fragment in their structures show potential in organic photonics - such as materials for organic light emitting diode application studies and organic solid state lasers. Additional incorporation of bulky triphenyl- groups in their structures gives them the ability to form thin amorphous solid films from volatile non-polar organic solvents. Unfortunately, there is still no clear relation between compound organic structures and their thermal and optical properties. In order to investigate the above mentioned regularities we have synthesized a series of tripheyl- group containing derivates of 2,6-bis-styryl-4…
MbCO embedded in trehalosyldextrin matrices: thermal effects and protein-matrix coupling
2010
Saccharide-based biopreservation is widely studied because of its scientific importance and possible technological outcomes for food and pharmaceutical industries. Ternary protein/saccharide/water systems have been extensively exploited to model the characteristics of the in vivo biopreservation process. A tight, water dependent, protein–matrix coupling has been shown to occur in various simple saccharide amorphous matrices, which is stronger in trehalose. The efficiency as bioprotectant of trehalose has been ascribed to this tight coupling, since the appearance of damages on biological structures will more involve structural variations of the surrounding matrix. Here we present, as an appl…
Photovoltaic effect in bulk heterojunction system with glass forming indandione derivative DMABI-6Ph
2018
The aim of the work is to evaluate possible use of 2-[[4-(bis(2-trityloxyethyl)amino)phenyl]methylene]indane-1,3-dione (DMABI-6Ph) as light absorbing material for solar cells. DMABI-6Ph is a perspective material due to its good photoelectrical, thermal and chemical properties. The main advantage of DMABI-6Ph is its ability to form amorphous films by wet-casting methods thus allowing using the compound in organic solar cells made from solution. For now most popular materials for solution processable solar cells are polymer P3HT and fullerene derivative PCBM, but lot of investigations are in the field of new low molecular weight materials to replace the polymer. Photoelectrical measurements w…