Search results for "Anode"

Nanoporous alumina membranes filled with solid acid for thin film fuel cells at intermediate temperatures

2004

Thin film fuel cells have been fabricated by impregnation of inorganic porous membranes with inorganic proton conductor. Anodic alumina membranes (50 μm thick and pore diameter of 200 nm), filled with CsHSO4 salt have been used as protonic conductor in a hydrogen-oxygen fuel cell working between 423 and 443 K in dry atmosphere. Polarization curves at 433 K showing ohmic control with open circuit values near 0.8 V and short circuit current around 8 mA cm−2 have been obtained. Possible causes of degradation as well as alternative routes to overcome some of the problems encountered with this approach will be reported. Keywords: Solid acid, Anodic alumina membranes, Pore filling, Thin film fuel…

Metodo di realizzazione di un elettrodo ad elevata densità energetica ed elettrodo ottenibile con tale metodo

2010

Electrosynthesis of Sn-Co nanowires in alumina membranes

2010

A fabrication process of amorphous nanowires of Sn-Co alloys, based on electrodeposition into anodic alumina membranes, is described. It is shown that nanowires of tin-cobalt alloys with different compositions can be produced by varying electrodeposition time and concentration ratio of salts dissolved into the electrolytic bath. Importance of the chelating agent to produce amorphous Sn-Co alloys has also been addressed. Electrodepositions were carried out potentiostatically at -1 V versus Saturated Calomel Electrode and 60 degrees C for times ranging from 10 to 90 minutes; the atomic fraction of Co2+ in the aqueous electrolyte (Co2+/(Co2+ + Sn2+)) was varied from 0.33 to 0.67. Nanowires asp…

Forming-Free and Self-Rectifying Resistive Switching Effect in Anodic Titanium Dioxide-Based Memristors

2018

The paper presents the resistive switching of electroforming-free Ti/anodic- TiO 2 /Cu memristors. Anodic TiO 2 thin films were prepared by anodizing Ti layers. Microscale devices were fabricated by direct laser-assisted photolithography. Experimental results showed a bipolar and self-rectifying behavior of the devices, which could be useful for crossbar array configurations. Moreover, a gradual resistive switching of the devices in both directions was observed, indicating the presence of multi-level resistance states.

X-ray Absorption under Operating Conditions for Solid-Oxide Fuel Cells Electrocatalysts: The Case of LSCF/YSZ

2019

We describe a novel electrochemical cell for X-ray absorption spectroscopy (XAS) experiments during electrical polarization suitable for high-temperature materials such as those used in solid oxide fuel cells. A half-cell LSCF/YSZ was then investigated under cathodic and anodic conditions (850 &deg

Spectroscopic response and charge transport properties of CdZnTe detectors grown by the vertical Bridgman technique

2015

In this work, we present the results of spectroscopic investigations on CdZnTe (CZT) detectors grown by the boron oxide encapsulated vertical Bridgman technique (1MEM-CNR, Parma, Italy). The detectors, with different thicknesses (1 and 2.5 mm), are characterized by the same electrode layout (gold electroless contacts): the anode is a central electrode (2 x 2 mm(2)) surrounded by a guard-ring electrode, while the cathode is a planar electrode covering the detector surface (4.1 x 4.1 mm(2)). The results of electrical investigations point out the low leakage currents of these detectors even at high bias voltages: 38 nA/cm(2) (T = 25 degrees C) at 10000 V/cm. The time stability and the spectros…

A phenomenological approach to the mechanical breakdown of anodic oxide films on zirconium

1986

Abstract A phenomenological theory of the mechanical breakdown of films growing on valve metals during galvanostatic oxidation is presented and discussed in detail for ZrO2 anodic films. It is shown that the mechanical breakdown voltage, Vmb, can be linearly related to the logarithm of the anodizing current density both in the case of constant and variable critical thickness, Lc, at which the breakdown occurs. It is also shown that the Amb and Bmb parameters of the relationship: Vmb = Amb + Bmb log i are strictly related to the kinetic parameters of growth of the films in the different solutions. The expressions of Amb and Bmb parameters are derived for films grown in the presence as well a…

Manufacturing and characterization of single cell intermediate-temperature solid oxide fuel cells for APU in transportation application

2014

The fabrications of large area IT-SOFC planar cell by new simple and cost effective process were explained. The optimization of the new process with respect to pore formers, thickness of layers, sintering temperature were performed. The electrochemical results of 10cm2 performed in Fiaxell open flange set up were detailed with respect to different configuration. Long term ageing performance tests of single cells were conducted in Fiaxell device and results are discussed. Preparation of new test bench and stacking process performed till now were briefed.

On the Effect of Surface Treatment to Improve Oxidation Resistance and Conductivity of Metallic Interconnects for SOFC in Operating Conditions

2008

International audience; Due to the reduction of operating temperature from 1000°C to 800°C, chromia forming alloys are the best candidates for interconnects in Solid Oxide Fuel Cells (SOFCs). These interconnects have to be operational in service conditions, at 800°C in air (cathode side) and in humidified hydrogen (anode side). The performance of the interconnect stainless steels is limited by the oxide scale formation (chromia), the low electronic conductivity of this scale and the possible volatility of chromium oxides. In the field of high temperature oxidation of metals, it is well known that the addition of a nanometric layer made of reactive element oxide such as, La2O3, Nd2O3 and Y2O…

Elaboration and interfacial reactivity of Lanthanum Strontium Chromium Ruthenium (LSCrRu) perovskite oxides as intermediate temperature fuel cell (IT…

2005

New data on the interest of ruthenium doped lanthanum strontium chromite La1-xSrxCr1-yRuyO3δ (LSCrRu) as anode in ITSOFC are presented. Microwave synthesis of mixed oxides allowed shaping of half-cells and complete cells using sputtering and screen printing methods. LSCrRu methane reforming property had been studied in a mono-chamber system coupled with a mass spectrometer in collaboration with Institut de REcherche Hydro-Québec. Anode/electrolyte interfacial reactivity had been analysed using SIMS and XRD on half cells models after ageing under H2 at 800°C. This experiment gave the chemical composition of the film after treatment. Complete cells, tested under working conditions, highlight…