Search results for "Bending"
showing 10 items of 244 documents
Self-Healing Properties of Bioinspired Amorphous CaCO3/Polyphosphate-Supplemented Cement
2020
There is a strong interest in cement additives that are able to prevent or mitigate the adverse effects of cracks in concrete that cause corrosion of the reinforcement. Inorganic polyphosphate (polyP), a natural polymer that is synthesized by bacteria, even those on cement/concrete, can increase the resistance of concrete to progressive damage from micro-cracking. Here we use a novel bioinspired strategy based on polyP-stabilized amorphous calcium carbonate (ACC) to give this material self-healing properties. Portland cement was supplemented with ACC nanoparticles which were stabilized with 10% (w/w) Na&ndash
Electronic and optical properties of carbon nanotubes under pure bending
2010
The high aspect ratio of carbon nanotubes makes them prone to bending. To know how bending affects the tubes is therefore crucial for tube identification and for electrical component design. Very few studies, however, have investigated tubes under small bending well below the buckling limit, because of technical problems due to broken translational symmetry. In this Brief Report a cost-effective and exact modeling of singe-walled nanotubes under such small bending is enabled by revised periodic boundary conditions, combined with density-functional tight-binding. The resulting, bending-induced changes in electronic and optical properties fall in clear chirality-dependent trend families. Whil…
Manipulation of charge transfer and transport in plasmonic-ferroelectric hybrids for photoelectrochemical applications
2016
Utilizing plasmonic nanostructures for efficient and flexible conversion of solar energy into electricity or fuel presents a new paradigm in photovoltaics and photoelectrochemistry research. In a conventional photoelectrochemical cell, consisting of a plasmonic structure in contact with a semiconductor, the type of photoelectrochemical reaction is determined by the band bending at the semiconductor/electrolyte interface. The nature of the reaction is thus hard to tune. Here instead of using a semiconductor, we employed a ferroelectric material, Pb(Zr,Ti)O3 (PZT). By depositing gold nanoparticle arrays and PZT films on ITO substrates, and studying the photocurrent as well as the femtosecond …
Evaluation of continuous filament mat influence on the bending behaviour of GFRP pultruded material via Electronic Speckle Pattern Interferometry
2017
Abstract Pultrusion is a process allowing the production of unidirectional (roving) fibre-reinforced polymer (FRP) structural elements with constant cross section. Recently, also civil engineers focused their attention on pultruded composite materials as alternative to traditional ones (e.g., concrete, steel). Furthermore, to improve the transverse strength and stiffness with respect to the fibres direction, continuous filament mat (CFM) is often placed within the stacking sequence. The CFM influence on the global mechanical behaviour is not considered by appropriate actual international standards. In this paper, the influence of the CFM layers on the mechanical behaviour of glass fibres pu…
Influence of oblique edge blanking on the online punching quality after stretch bending
2018
The oblique edge punching was proposed to reduce the surrounding sag failure occurred under the large punching force during online punching after stretch bending. The finite element models under three different kinds of punches were stablished and the punching processes were simulated by using the DEFORM-3D software. Comparison between the flat-edge punch and the oblique edge punches were realized, and the optimal height of the oblique edge of the unilateral bevelled punch and the single-peak bevelled punch were obtained. Three kinds of punches were designed based on the simulation results, and the experiments for manufacturing the upper strip of the automobile door frame by the online punc…
On the Effect of Interference Fits in Composite Pin-Joints
1999
The Finite Element Method is used to determine the effect of pin/hole interference fits on the elastic membranal behavior of an orthotropic plate loaded in tension through a pin. A complete contact analysis is performed to handle the nonlinear contact problem. The study encompasses two levels of interference fits, two degrees of anisotropy of the plate, and two load levels. Friction effects are not included. Experimental results from Digital Speckle Pattern Interferometry are also presented. It is shown that the stress changes in the plate vary linearly with load when no pin/plate separation occurs. It is also shown that interference fits can have beneficial effects on the static and fatig…
Effect of the fiber geometry on the pullout response of mechanically deformed steel fibers
2013
Abstract A simple model to predict the influence of fiber geometry on the pullout of mechanically deformed steel fibers from cementitious matrix is proposed. During the pullout the mechanically deformed fiber is subjected to repetitive bending and unbending which cause an increase of the tension in the fiber. This increase of the tension depends on the amount of plastic work needed to straighten the fiber during pullout. The model input parameters are mechanical and geometrical properties of mechanically deformed fibers. Model predictions were compared to the experimental results on the hooked-end and crimped steel fiber pullout and good agreement was observed.
Temperature Measurements as a Method for Monitoring Ropes
2020
Due to an increasing demand for operation at sea depths as low as 3000 m and under, the use of fibre ropes for offshore application in deep sea lifting and mooring is increasing. Consequently, improved knowledge is required regarding these ropes’ thermo-mechanical properties and how these properties change as the rope is being used. This paper presents a 2D model of heat transport in the axial and radial directions along a 28 mm diameter fibre rope typically used for offshore applications. The model is combined with temperature measurements during heating and cooling of the rope, using both thermocouples and a thermal camera. Measurements are performed both on a new rope and on a used that …
Experimental Method for Determining Forces at Bending of Perforated Plates
2017
Abstract This paper describes the method of calculating the forces which appear at the bending of perforated plates with holes of different shapes and placed in different patterns, by means of a dynamometric table which uses resistive tensometric transducers (strain gauges). It also describes an instrument for the recording of data from the dynamometric table, a tool created with the aid of the “TestPoint” software which, beneath the data recording, ensures the filtering and statistic processing of data. The obtained results are displayed in comparative graphs for six types of perforated plates, as well as for an unperforated plate.
Experimental Study Regarding of Bending Behaviour of Stabilizator Link
2016
Abstract This paper presents an experimental study of the behavior of anti-roll power link subjected to bending, power link coming from an Opel Astra G. The power link is made of PA66 GF30 polyamide. For this study, there were used a universal testing machine (Instron 5587) and a real-time strain measurement optical system (Aramis). The results showed are those obtained in the case of a compression force of 1,000 [N] namely: major Strain ε1, minor strain ε2, equivalent von Mises strain, displacement on X axis, displacement on Y axis (compression force direction), displacement on Z axis.