Search results for "Biofouling"
showing 10 items of 30 documents
Sub-critical filtration conditions of commercial hollow-fibre membranes in a submerged anaerobic MBR (HF-SAnMBR) system: The effect of gas sparging i…
2012
A submerged anaerobic MBR demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON®, Koch Membrane Systems, PUR-PSH31) was operated using municipal wastewater at high levels of mixed liquor total solids (MLTS) (above 22gL -1). A modified flux-step method was applied to assess the critical flux (J C) at different gas sparging intensities. The results showed a linear dependency between J C and the specific gas demand per unit of membrane area (SGD m). J C ranged from 12 to 19LMH at SGD m values of between 0.17 and 0.5Nm 3h -1m -2, which are quite low in comparison to aerobic MBR. Long-term trials showed that the membranes operated steadily at fluxes close to the est…
Improved antifouling properties and selective biofunctionalization of stainless steel by employing heterobifunctional silane-polyethylene glycol over…
2016
AbstractA straightforward solution-based method to modify the biofunctionality of stainless steel (SS) using heterobifunctional silane-polyethylene glycol (silane-PEG) overlayers is reported. Reduced nonspecific biofouling of both proteins and bacteria onto SS and further selective biofunctionalization of the modified surface were achieved. According to photoelectron spectroscopy analyses, the silane-PEGs formed less than 10 Å thick overlayers with close to 90% surface coverage and reproducible chemical compositions. Consequently, the surfaces also became more hydrophilic, and the observed non-specific biofouling of proteins was reduced by approximately 70%. In addition, the attachment of E…
Environmental impact of antifouling technologies: state of art and perspectives
2001
1. Marine fouling affects most man-made surfaces temporarily or permanently immersed in the sea, resulting in significant (or substantial) economic costs. Intense research is aimed at preventing or reducing fouling. 2. The most widespread solution to avoid fouling formation is to make surfaces unsuitable for settlers, coating them with antifouling (AF) paints containing toxic compounds. Most AF agents (e.g. tributyltin, (TBT)) have undesirable effects on non-target species, including commercially important organisms. 3. To date, the use of TBT in AF paints has been restricted (but not prohibited) in a number of countries and new biocides are in use. 4. The environmental problems posed to ma…
Nanozymes in Nanofibrous Mats with Haloperoxidase-like Activity To Combat Biofouling.
2018
Electrospun polymer mats are widely used in tissue engineering, wearable electronics, and water purification. However, in many environments, the polymer nanofibers prepared by electrospinning suffer from biofouling during long-term usage, resulting in persistent infections and device damage. Herein, we describe the fabrication of polymer mats with CeO2–x nanorods that can prevent biofouling in an aqueous environment. The embedded CeO2–x nanorods are functional mimics of natural haloperoxidases that catalyze the oxidative bromination of Br– and H2O2 to HOBr. The generated HOBr, a natural signaling molecule, disrupted the bacterial quorum sensing, a critical step in biofilm formation. The pol…
Performance of a polypropylene membrane contactor for the recovery of dissolved methane from anaerobic effluents: Mass transfer evaluation, long-term…
2018
Abstract A polypropylene membrane contactor was used for the recovery of dissolved methane from an anaerobic reactor effluent. Effect of operational parameters, operation mode and fouling on long-term operation was studied using vacuum pressure or N 2 as sweep gas. Results were analyzed based on the mass transfer estimations. Lower performance was observed in the shell-side mode due to the lower liquid velocity and the probable channeling. Membrane pore wetting was observed with the increase in Q L in the vacuum-pressure mode. This was confirmed with mass transfer resistance analysis, resulting in an estimated wetted pore fraction of between 0.25 and 0.53. The highest removal efficiencies w…
Submicrometer-Sized Roughness Suppresses Bacteria Adhesion.
2020
Biofilm formation is most commonly combatted with antibiotics or biocides. However, proven toxicity and increasing resistance of bacteria increase the need for alternative strategies to prevent adhesion of bacteria to surfaces. Chemical modification of the surfaces by tethering of functional polymer brushes or films provides a route toward antifouling coatings. Furthermore, nanorough or superhydrophobic surfaces can delay biofilm formation. Here we show that submicrometer-sized roughness can outweigh surface chemistry by testing the adhesion of E. coli to surfaces of different topography and wettability over long exposure times (>7 days). Gram-negative and positive bacterial strains are tes…
The efficient mixed matrix antifouling membrane for surfactant stabilized oil-in-water nanoemulsion separation
2019
Abstract Membrane technology has raised considerable interest in sustainable water purification over the past decade. The development of antifouling membranes is always the basic approach to address the omnipresent bottlenecks of the membrane fouling. In this study, AlSi2O6 nanoparticles were synthesized using a coprecipitation technique and their influence was investigated on the permeation and antifouling properties of ultrafiltration (UF) membranes of polysulfone (PSF). A series of membranes were fabricated with various concentrations (such as 0.0, 2.5, 5 and 7.5 wt%) of AlSi2O6 nanoparticles through diffusion induced phase separation method. The prepared composite membranes demonstrate …
Biofouling management in anaerobic membrane bioreactors
2020
Abstract This chapter is aimed at providing an insight on the main issues around the membrane fouling in anaerobic membrane bioreactors (AnMBRs). The analysis presented here shows that membrane fouling in AnMBRs is attributed to three major factors: membrane features, operating conditions, and wastewater characteristics. Several ad-hoc strategies have been implemented in literature to mitigate membrane fouling in AnMBRs, such as gas sparging, media addition, chemical cleaning, and membrane rotation/vibration. Among them, gas sparging is considered the most expensive strategy due to the high power requirement of the gas blower (up to 1.345 kWh m− 3). An accurate experimental and modeling ana…
Sequential batch membrane bio-reactor for wastewater treatment: The effect of increased salinity
2016
In this work, a sequential batch membrane bioreactor pilot plant is investigated to analyze the effect of a gradual increase in salinity on carbon and nutrient removal, membrane fouling and biomass kinetic parameters. The salinity was increased by 2 g NaCl L-1 per week up to 10 g NaCl L-1. The total COD removal efficiency was quite high (93%) throughout the experiment. A gradual biomass acclimation to the salinity level was observed during the experiment, highlighting the good recovery capabilities of the system. Nitrification was also influenced by the increase in salinity, with a slight decrease in nitrification efficiency (the lowest value was obtained at 10 g NaCl L-1 due to lower nitri…
Effect of C/N shock variation on the performances of a moving bed membrane bioreactor.
2015
Abstract The effect of a sharp variation of C/N ratio in a moving bed membrane bioreactor (MB-MBR) pilot plant treating high strength wastewater has been investigated. The experimental campaign was divided into two periods, each characterized by a different C/N ratio (namely, 2.5 and 15, Period 1 and Period 2, respectively). The MB-MBR system was analyzed in terms of organic carbon removal, nitrification efficiency, biokinetic activity and fouling behavior. The results showed that the nitrification process was severely affected by lower C/N value and by high concentration of ammonia. It was noticed an extensive stress effect on the autotrophic bacteria. Furthermore, it was observed an incre…