Search results for "Bone plate"

Minimally invasive plate fixation in femoral shaft fractures

1997

Bridge-plating with its advantages in terms of vascularity and bone healing is a well established procedure today in the treatment of comminuted femoral fractures. Bridge-plating means that the fracture site is not interfered with during the operative procedure. This paper introduces a surgical technique in which the plate is inserted through isolated proximal and distal incisions only, behind the vastus lateralis. Alignment is secured by the plates, the fracture site remains untouched, fixation and screw insertion is restricted to the proximal and distal main fragments. Longitudinal femoral fractures extending right into the trochanteric and or condylar areas are the main indication for mi…

A biomechanical evaluation of methods of distal humerus fracture fixation using locking compression plates versus conventional reconstruction plates.

2004

OBJECTIVES To examine the biomechanical behavior of 2 techniques of double-plate osteosynthesis for fractures of the adult distal humerus using conventional reconstruction plates and locking compression plates. DESIGN Basic science study. SETTING Experimental in vitro study. PATIENTS/PARTICIPANTS Forty fresh-frozen human distal humeri specimens. INTERVENTION Four matched groups with 10 humeri each, median age 74 years (46-95), were created using similar bone mineral density values. Two standard configurations of double-plate osteosynthesis (dorsal or 90 degrees configuration) with either conventional reconstruction plates or locking compression plates were studied for biomechanical properti…

Locked Plate Fixation and Intramedullary Nailing for Proximal Humerus Fractures: A Biomechanical Evaluation

2005

Background Internal fixation of proximal humeral fractures is associated with a considerable secondary malalignment rate. Fixed-angle implants have been suggested to increase the stability of fixation. Methods The biomechanical properties of four different implants were tested. These included an internal fixator with semi-elastic properties (reference), the Synthes T-plate, a locked plate with rigid properties and a spiral blade locked intramedullary nail (PHN). These implants were assessed in twenty-four osteotomized pairs of human cadaveric humeri. Specimens were subjected to two-hundred cycles of axial loading and torque followed by load to failure. Results The PHN had greater axial stif…

Surface Topographies of Glaucoma Drainage Devices and Their Influence on Human Tenon Fibroblast Adhesion

2010

PURPOSE. This study was performed to investigate the surface topography of different glaucoma drainage devices and to determine the effects of surface roughness on cell adhesion of cultured human tenon fibroblasts.METHODS. The surface topography of four widely used devices (Ahmed FP7 and Ahmed S-2; New World Medical, Inc., Rancho Cucamonga, CA; Baerveldt BG101-350; Advanced Medical Optics, Irvine, CA; and Molteno S1; Molteno Ophthalmic Ltd., Dunedin, New Zealand) was investigated by scanning electron microscopy, and roughness was quantified by white-light confocal microscopy. Cells were grown for 72 hours on the surfaces of implants affixed to standard culture dishes. The cells were labeled…

Acetabulumfrakturen im Alter

2002

Acetabular fractures in elderly patients are rare injuries, but their incidence is increasing. Poor bone quality due to osteoporosis and an increased operative risk due to concomitant disease are factors complicating surgical therapy. Literature does not provide generally accepted treatment protocols. In a 4-year period, 27 patients who were 65 years or older and who had an acute displaced fracture of the acetabulum were admitted to our department. Four minimally displaced and stable fractures were managed conservatively. Internal fixation was performed in 16 cases. According to the Merle d'Aubigne score, in 15 out of 18 surviving patients excellent or good results were found. Treatment str…

2014

Currently, antegrade intramedullary nailing and minimally invasive plate osteosynthesis (MIPO) represent the main surgical alternatives in distal tibial fractures. However, neither choice is optimal for all bony and soft tissue injuries. The Retrograde Tibial Nail (RTN) is a small-caliber prototype implant, which is introduced through a 2-cm-long incision at the tip of the medial malleolus with stab incisions sufficient for interlocking. During this project, we investigated the feasibility of retrograde tibial nailing in a cadaver model and conducted biomechanical testing. Anatomical implantations of the RTN were carried out in AO/OTA 43 A1-3 fracture types in three cadaveric lower limbs. B…

Stability of radial head and neck fractures: a biomechanical study of six fixation constructs with consideration of three locking plates.

2007

Open reduction and internal fixation of radial neck fractures can lead to secondary loss of reduction and nonunion due to insufficient stability. Nevertheless, there are only a few biomechanical studies about the stability achieved by different osteosynthesis constructs.Forty-eight formalin-fixed, human proximal radii were divided into 6 groups according to their bone density (measured by dual-energy x-ray absorptiometry). A 2.7-mm gap osteotomy was performed to simulate an unstable radial neck fracture, which was fixed with 3 nonlocking implants: a 2.4-mm T plate, a 2.4-mm blade plate, and 2.0-mm crossed screws, and 3 locking plates: a 2.0-mm LCP T plate, a 2.0-mm 6x2 grid plate, and a 2.0…

The Retrograde Tibial Nail: presentation and biomechanical evaluation of a new concept in the treatment of distal tibia fractures.

2013

Displaced distal tibia fractures require stable fixation while minimizing secondary damage to the soft tissues by the surgical approach and implants. Antegrade intramedullary nailing has become an alternative to plate osteosynthesis for the treatment of distal metaphyseal fractures over the past two decades. While retrograde intramedullary nailing is a standard procedure in other long bone fractures, only few attempts have been made on retrograde nailing of tibial fractures. The main reasons are difficulties of finding an ideal entry portal and the lack of an ideal implant for retrograde insertion. The Retrograde Tibial Nail (RTN) is a prototype intramedullary implant developed by our group…

Biomechanical testing of different posterior fusion devices on lumbar spinal range of motion.

2019

Abstract Background Recent minimal-invasive posterior fusion devices are supposed to provide stability and obtain fusion in combination with interbody cages in the instrumented segment. The aim of the present study is to evaluate the primary stability of two minimal-invasive posterior prototypes compared to an established spinous process plate and standard pedicle screw instrumentation. Methods Seven fresh frozen human cadaver lumbar spines (L2–L5) were tested in a spinal testing device with a moment of 7.5 Nm. Spinal stability was determined as mean range of motion (RoM) in the segment L3/L4 during extension-flexion, lateral bending and axial rotation. The RoM was measured during five cond…

Treatment of distal intraarticular tibial fractures: A biomechanical evaluation of intramedullary nailing vs. angle-stable plate osteosynthesis

2015

In factures of the distal tibia with simple articular extension, the optimal surgical treatment remains debatable. In clinical practice, minimally invasive plate osteosynthesis and intramedullary nailing are both routinely performed. Comparative biomechanical studies of different types of osteosynthesis of intraarticular distal tibial fractures are missing due to the lack of an established model. The goal of this study was first to establish a biomechanical model and second to investigate, which are the biomechanical advantages of angle-stable plate osteosynthesis and intramedullary nailing of distal intraarticular tibial fractures. Seven 4(th) generation biomechanical composite tibiae feat…