Search results for "Bust"

Claustre Obert: Enrique Bustamante

2013

'Democràcia i informació: canvis en el sistema mediàtic i crisi' és el títol de la conferència que oferirà hui dimarts, 21 de maig, el catedràtic de Comunicació Audiovisual i Publicitat de la Universitat Complutense de Madrid Enrique Bustamante, a l'Aula Magna del Centre Cultural La Nau de la Universitat (18:30 hores).

Modelling of Mercury Emissions from Large Solid Fuel Combustion and Biomonitoring in CZ-PL Border Region

2016

Abstract Tightening of norms for air protection leads to a development of new and significantly more effective techniques for removing particulate matter, SOx and NOx from flue gas which originates from large solid fuel combustion. Recently, it has been found that combinations of these environmental technologies can also lead to the reduction of mercury emissions from coal power plants. Now the greatest attention is paid especially to the coal power plant in Opatovice nad Labem, close to Hradec Kralove. Its system for flue gas dedusting was replaced by a modern type of cloth fabric filter with the highest particle separation efficiency which belongs to the category of BAT. Using this techno…

Tetra- and pentachlorodibenzothiophenes are formed in waste combustion

1991

Abstract Two different waste combustion samples have been analyzed for tetra- and pentachlorodibenzothiophenes. HRGC/HRMS with a resolution of 20 000 was used for identification. By resolution of 10 000 chlorinated dibenzo-p-dioxins and some unknown compounds gave GC/SIM peaks at the exact masses of the chlorinated dibenzothiophenes. These peaks were no more present by resolution 20 000. Several tetra- and pentachlorodibenzothiophenes were found in both samples. In the other one of the samples the concentrations were seemingly high although exact quantitative determination could not be done.

Chlorinated dioxins and dibenzothiophenes in fly ash samples from combustion of peat, wood chips, refuse derived fuels and liquid packaging boards

1995

Abstract Peat, wood chips, refuse derived fuel and liquid packaging board in different combinations were burned at a temperature of at least 850 °C. Fly ash samples from these combustions were analyzed for polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzothiophenes (PCDBTs) by high resolution GC/MS. The concentrations of tri- and tetrachlorodibenzothiophenes and tri-, tetra- and pentachlorodioxins were highest when mixtures of wood chips and refuse derived fuel (RDF) were burned. The fly ash from the combustion of pure peat pellets did not contain any polychlorinated dibenzothiophenes. When wood chips and RDF were burned the concentrations of chlorinated compounds in fly…

Performance assessment of individual and ensemble data-mining techniques for gully erosion modeling

2017

Gully erosion is identified as an important sediment source in a range of environments and plays a conclusive role in redistribution of eroded soils on a slope. Hence, addressing spatial occurrence pattern of this phenomenon is very important. Different ensemble models and their single counterparts, mostly data mining methods, have been used for gully erosion susceptibility mapping; however, their calibration and validation procedures need to be thoroughly addressed. The current study presents a series of individual and ensemble data mining methods including artificial neural network (ANN), support vector machine (SVM), maximum entropy (ME), ANN-SVM, ANN-ME, and SVM-ME to map gully erosion …

Mineral Deposit Formation in Gas Engines During Combustion of Biogas from Landfills and Municipal WWTP

2020

Abstract The biogas produced in municipal wastewater-treatment plants (WWTP) should be cleaned before it can be used as a fuel in internal combustion engines. Efficient running of such engines is possible only subject to using high quality biogas and lubricating oil. Otherwise, biogas impurities in course of complex chemical reactions may form deposits on various engine parts as well as seriously contaminate the lubricating oil. In this paper, mineral deposits containing high concentration of bismuth, silicon, sulphur, calcium and zinc are studied. Silicon deposits demonstrating strong friction properties are formed during combustion of volatile silica compounds. As these deposits build up,…

PCDDs, PCDFs, PCDTs, PCBs and some other organochlorine compounds in pine needles exposed to pulp and paper mill emissions and effects of waste combu…

1997

Concentrations of semivolatile chlorinated organic compounds α-HCH, lindane, HCB, DDT, DDE, DDD, chlordanes and PCBs, and low-volatility compounds PCDDs, PCDFs and PCDTs in pine needles in a recipient area of the emissions from a pulp and paper mill where also waste combustion was done were measured. Mostly, the concentrations were found to be near the background levels. Elevated concentrations of HCB, some PCB congeners and some HxCDF isomers in samples from two sampling points were observed. Some other possible point sources of these compounds are situated in the vicinity of the pulp and paper mill.. Also the community of Pietarsaari is one possible source of the slightly elevated concent…

Influence of mw pretreatment on main gasification/combustion characteristics of different types of biomass

2020

On the Talmud Division: Equity and Robustness

2008

The Talmud Division is a very old method of sharin g developed by the rabbis in the Talmud and brought to the fore in the modern area s ome authors, among them are Aumann and Maschler. One compares the Talmud Division to other methods, mainly here the most popular, Aristotle's Proportional Division, but also to the equal division. The Talmud Division is more egalitarian than the Proportional Division for smal l levels of estate and conversely and it protects the weakest -those who cannot place a non-zero clai m-. This suggests that claimants may choose among the claiming methods depending on their interest, what implies a metagame. Unlike other methods as the Proportional Division, the Talm…

Robust dynamic comfort modeling for motorcycle riding

2015

Comfort modeling is considered a prerequisite in motorcycle design, primarily to address safety concerns and to position the product on the market. However, a comprehensive methodology for comfort modeling during the earliest development phases of a motorcycle model is still missing. Anthropometrical variation is the main noise factor to consider in comfort modeling in relation to the unavoidable variability of body segments. However, comfort is a subjective concept influencing riders' choice of motorcycle model. This work is a generalization of the robust ergonomic design methodology aimed at designing products whose ergonomic performance is insensitive to anthropometrical variation. This …