Search results for "CIRCUIT"

Study of the Secondary Electron Yield in Dielectrics Using Equivalent Circuital Models

2018

[EN] Secondary electron emission has an important role on the triggering of the multipactor effect; therefore, its study and characterization are essential in radio-frequency waveguide applications. In this paper, we propose a theoretical model, based on equivalent circuit models, to properly understand charging and discharging processes that occur in dielectric samples under electron irradiation for secondary electron emission characterization. Experimental results obtained for Pt, Si, GaS, and Teflon samples are presented to verify the accuracy of the proposed model. Good agreement between theory and experiments has been found.

Mixed-Mode Operation of Hybrid Phase-Change Nanophotonic Circuits

2016

Phase change materials (PCMs) are highly attractive for nonvolatile electrical and all-optical memory applications because of unique features such as ultrafast and reversible phase transitions, long-term endurance, and high scalability to nanoscale dimensions. Understanding their transient characteristics upon phase transition in both the electrical and the optical domains is essential for using PCMs in future multifunctional optoelectronic circuits. Here, we use a PCM nanowire embedded into a nanophotonic circuit to study switching dynamics in mixed-mode operation. Evanescent coupling between light traveling along waveguides and a phase-change nanowire enables reversible phase transition b…

Identification of parameters and harmonic losses of a deep-bar induction motor

2017

High frequency harmonics from a frequency converter causes additional losses in a deep-bar induction motor. The harmonics have their own amplitude and phase with respect to the fundamental signal, but the harmonic loss is only dependent on the amplitude of harmonics. A deep-bar induction motor can be modelled by a triple-cage circuit to take skin effect into account. The triple cage circuit having many parameters could be estimated from a small-signal model of the machine by using Differential Evolution. The correctly estimated parameters make the triple-cage circuit valid in a wide range of frequencies. However, the triple-cage circuit is very complicated which makes it difficult to model …

2019

We present a design for producing precisely adjustable and alternating single-axis magnetic fields based on nested Halbach dipole pairs consisting of permanent magnets only. Our design allows for three dimensional optical and mechanical access to a region with strong adjustable dipolar fields, is compatible with systems operating under vacuum, and does not effectively dissipate heat under normal operational conditions. We present a theoretical analysis of the properties and capabilities of our design and construct a proof-of-concept prototype. Using our prototype, we demonstrate fields of up to several kilogauss with field homogeneities of better than 5%, which are harmonically modulated at…

A summary of expressions for central performance parameters of high efficiency solar cell concepts

2019

This work reviews expressions for central performance parameters of various types of PV-concepts when operating at the radiative limit. Some new expressions not published elsewhere are also included. The performance parameters include the short circuit current density, the open circuit voltage, the maximum power density and the optimal voltage. The cell concepts include single junction cells, cells optically coupled to up- and down-converters, intermediate band solar cells and a couple of implementations of multijunction devices. The Lambert W function is used to express the maximum power density.

A Novel Fault-Tolerant Routing Algorithm for Mesh-of-Tree Based Network-on-Chips

2019

Use of bus architecture based communication with increasing processing elements in System-on-Chip (SoC) leads to severe degradation of performance and speed of the system. This bottleneck is overcome with the introduction of Network-on-Chips (NoCs). NoCs assist in communication between cores on a single chip using router based packet switching technique. Due to miniaturization, NoCs like every Integrated circuit is prone to different kinds of faults which can be transient, intermittent or permanent. A fault in any one component of such a crucial network can degrade performance leaving other components non-usable. This paper presents a novel Fault-Tolerant routing Algorithm for Mesh-of-Tree …

Silicon dosimeters based on Floating Gate Sensor: design, implementation and characterization

2020

A rad-hard monolithic dosimeter has been implemented and characterized in a standard 180 nm CMOS technology. The radiation sensor (C-sensor) is based on a Floating Gate (FG) MOS discharge principle. The output current is processed by a current-to-voltage (I/V) interface and then converted by a 5-bit flash ADC. The dosimeter is re-usable (FG can be recharged) and can detect a dose up to 1krad (Si) with a resolution of 30rad (Si) typical over temperature 0 to 85°C range. The ADC allows easy further signal processing for calibration and averaging, etc. The power consumption of C-sensor plus I/V interface is < 2mW from a 5 V power supply. The overall layout area is less than 0.25mm2. The Rad…

Simplified feedback control system for scanning tunneling microscopy

2021

A Scanning Tunneling Microscope (STM) is one of the most important scanning probe tools available to study and manipulate matter at the nanoscale. In a STM, a tip is scanned on top of a surface with a separation of a few \AA. Often, the tunneling current between tip and sample is maintained constant by modifying the distance between the tip apex and the surface through a feedback mechanism acting on a piezoelectric transducer. This produces very detailed images of the electronic properties of the surface. The feedback mechanism is nearly always made using a digital processing circuit separate from the user computer. Here we discuss another approach, using a computer and data acquisition thr…

Contrasting topologies for regular interconnection networks under the constraints of nanoscale silicon technology

2010

Nowadays, system designers have adopted Networks-on-Chip as communication infrastructure of general-purpose tile-based Multi-Processor System-on-Chip (MPSoC). Such decision implies that a certain topology has to be selected to efficiently interconnect many cores on the chip. To ease such a choice, the networking literature offers a plethora of works about topology analysis and characterization for the off-chip domain. However, theoretical parameters and many intuitive assumptions of such off-chip networks do not necessarily hold when a topology is laid out on a 2D silicon surface. This is due to the distinctive features of silicon technology design pitfalls. This work is a first milestone t…

FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller

2020

The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…