Search results for "COSTRUZIONE"
showing 10 items of 669 documents
Enhancement of Static and Fatigue Strength of Short Sisal Fiber Biocomposites by Low Fraction Nanotubes
2021
AbstractThanks to good mechanical performances, high availability, low cost and low weight, the agave sisalana fiber allows to obtain biocomposites characterised by high specific properties, potentially very attractive for the replacement of synthetic materials in various industrial fields. Unfortunately, due to the low strength versus transversal damage processes mainly related to the matrix brittleness and/or to the low fiber/matrix adhesion, the tensile performance of random short fiber biocomposites are quite low, and to date most of the fiber treatments proposed in literature to improve the fiber-matrix adhesion, have not led to very satisfactory results. In order to overcome such a dr…
Mode I translaminar fracture toughness of high performance laminated biocomposites reinforced by sisal fibers: Accurate measurement approach and lay-…
2022
Abstract The present work performs a systematic experimental analysis of the translaminar fracture behavior of high performance biocomposites constituted by green epoxy reinforced by sisal fibers, by varying the main influence parameters as fiber concentration and lay-up. Despite the corrective function properly introduced to take into account the anisotropy as well as the use of the equivalent crack length, the study shows that the LEFM does not give accurate estimations of the fracture toughness, because the extension of the near tip damaged zone is higher than the singular dominated one. Accurate estimations can be obtained instead by the proposed modified area method that takes into acc…
Interlaminar fracture toughness behavior of electron-beam cured carbon-fiber reinforced epoxy-resin composites
2013
The work describes the preparation and physical-mechanical characterization of unidirectional CFRP panels manufactured by an electron beam curing technique. Delamination fracture toughness in Mode I and II is investigated in order to evaluate the influence of fiber–matrix adhesion strength, matrix toughness and matrix crosslinking density as determined by the radiation curing process. A matrix system comprising a DGEBA epoxy monomer and an initiator of cationic polymerization have been used, with one batch of resin mixed with a PES monomer in order to enhance matrix toughness. Curing was achieved with a pulsed 10 MeV Electron Beam accelerator. Thermally cured composite systems have also bee…
Turismo ed effetto città
2009
Model-assisted ultrasonic calibration using intentionally embedded defects for in-process weld inspection
2021
Abstract Automated in-process Non-Destructive Testing (NDT) systems are rapidly gaining traction within the manufacturing industry as they reduce manufacturing time and costs. When considering calibration and verification of such systems, creating defects of known geometry and nature during the deposition of a weld can: (I) help examine the capability of the automated system to detect and characterise defects, (II) be used to form a database of signals associated with different defect types to train intelligent defect classification algorithms, and (III) act as a basis for in-process gain calibration during weld inspection at high temperatures, where the ultrasound beam can be skewed as a r…
Continuous monitoring of an intentionally-manufactured crack using an automated welding and in-process inspection system
2020
Abstract Automated weld deposition coupled with the real-time robotic Non-Destructive Evaluation (NDE) is used in this paper. For performance verification of the in-process inspection system, an intentionally embedded defect, a tungsten rod, is introduced into the multi-pass weld. A partially-filled groove (staircase) sample is also manufactured and ultrasonically tested to calibrate the real-time inspection implemented on all seven layers of the weld which are deposited progressively. The tungsten rod is successfully detected in the real-time NDE of the deposited position. The same robotic inspection system was then used to continuously monitor an intentionally-manufactured crack for 20 h.…
Ultrasonic phased array inspection of wire plus arc additive manufacture (WAAM) samples using conventional and total focusing method (TFM) imaging…
2018
In this study, three aluminium samples produced by wire + arc additive manufacture (WAAM) are inspected using ultrasonic phased array technology. Artificial defects are machined using a centre drill, ø3 mm, and electro-discharge machining (EDM), ø0.5-1 mm, in a cylindrical through hole topology. The sample was first inspected by a single element wheel probe mounted on a KUKA robot in order to investigate the feasibility of using a conventional ultrasonic transducer approach. Unfortunately, the wheel probe was found to be unsuitable for scanning of the WAAM specimens and ultrasonic phased arrays were employed next. The setup included 5 MHz and 10 MHz arrays (128 elements) in direct contact w…
Luoghi urbani scomparsi e architetture mai realizzate nella riconfigurazione 3D del Rione Conceria di Palermo
2018
L'oggetto di studio è lo scomparso Rione Conceria all'interno del Centro Storico di Palermo. È una vasta area urbana, che si estende lungo la Via Maqueda, Via Roma, Corso Vittorio Emanuele e Via Bandiera, che storicamente faceva parte di un unico sistema urbano che cuciva il mercato del Capo con il Mercato della Vucciria. Le operazioni urbanistiche del secolo scorso (il taglio di via Roma, il il progetto di riorganizzazione dell'intero rione, la costruzione della Galleria delle Vittorie) hanno cancellato quasi definitivamente sia le sue presenza architettoniche che l'impianto del suo tessuto viario. The object of study is the disappeared Rione Conceria inside the Historical Center of Palerm…
Il restauro virtuale dei sistemi decorativi e studio ricostruttivo dell’insula
2018
Il presente contributo rientra nell’ambito di in una più vasta linea di ricerca denominata “Progetto Hierapolis Virtuale”, sviluppata a partire dal 2007 e finalizzata alla ricostruzione tridimensionale degli edifici della città. A differenza di altre ricerche condotte sui monumenti di Hierapolis, l’attuale studio riguarda solamente una singola fase edilizia dell’insula, relativa alla grande stagione monumentale di età protobizantina riferibile a un periodo posto tra il VI e la prima metà del VII secolo. Tale scelta è stata dettata unicamente dalla quantità e dalla qualità dei dati archeologici utili ad uno studio ricostruttivo il più possibile scientifico per contribuire ad una maggiore con…
Experimental determination of mode I fracture parameters in orthotropic materials by means of Digital Image Correlation
2020
Abstract The mode I fracture parameters for an orthotropic body are directly calculated from full-field deformation measurements provided by Digital Image Correlation (DIC). Three complementary and direct approaches are evaluated and compared: (i) the determination of the Stress Intensity Factor (SIF) by fitting the displacement field using the analytical expression proposed by Lekhnitskii; (ii) the determination of the J-Integral by using the Energy Domain Integral (EDI) formulation on the raw DIC data; and (iii) the calculation of the J-Integral using the EDI approach on the displacement data fitted using Lekhnitskii’s formulation. A comparative experimental study is performed by testing …