Search results for "Civil Engineering"
showing 10 items of 1216 documents
Pd supported on magnetic carbon coated halloysite as hydrogenation catalyst: Study of the contribution of carbon layer and magnetization to the catal…
2019
Abstract In this article, a magnetic carbon-coated halloysite nanoclay (Hal) was prepared through introduction of hydrothermally carbonized glucose (Glu) on Hal followed by the immobilization of magnetic nanoparticles (MNPs) and incorporation of resorcinol-formaldehyde polymeric shell (RF) and carbonization. The resulting composite was then successfully applied for the immobilization of Pd nanoparticles to afford Pd@Hal@Glu-Fe-C that could efficiently promote hydrogenation of nitroarenes in the aqueous media at low temperature. The catalyst exhibited high selectivity toward nitro group. Moreover, it was highly recyclable with low MNPs and Pd leaching. To elucidate the contribution of each c…
Thermal and moisture adsorption/desorption properties for a selection of vegetal insulation materials
2019
Natural, or ‘green’ insulation materials, have become more popular for the ‘ecologisation’ of construction activities. The ecological aspects for such materials are being widely analysed, but experimental data about their physical properties when installed in building constructions remains lacking. In this study, pressed samples of three locally wild grown agricultural materials – rye, reed, and hemp – are analysed. Thermal conductivity measurements were carried out using the hot plate device. Comparison with widely used mineral insulation materials shows that thermal conductivity for simple pressed materials are roughly three times higher, and are comparable to plywood and cross-laminated …
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Comparative analysis of bonding mechanism in solid state metal working processes
2016
The Piwnik and Plata pressure-time bonding criterion was applied to Friction Stir Welding, Linear Friction Welding, Porthole Extrusion and Roll Bonding. A neural network was set up, trained and used to predict the bonding occurrence starting from the main field variable distributions calculated through specific numerical models developed for each process. The analysis of the results permitted to predict the occurrence of solid bonding and to highlight differences and analogies between the processes in order to obtain sound solid welds.
Masonry columns confined with fabric reinforced cementitious matrix (FRCM) systems: A round robin test
2021
Abstract The conservation and the preservation of existing masonry buildings, most of them recognized as cultural heritage, require retrofitting techniques that should reduce the invasiveness and assure reversibility and compatibility with the substrate. In this perspective, the strengthening system should be able to improve the bearing capacity of the structural member and, at the same time, to assure mechanical and material compatibility. The use of Fabric Reinforced Cementitious Matrix (FRCM) composites is now recognized to be suitable for these purposes. Indeed, the inorganic matrix has comparable properties with respect to the existing historical mortars while the fabric has relevant t…
Graphene Oxide Carboxymethylcellulose Nanocomposite for Dressing Materials.
2020
Sore, infected wounds are a major clinical issue, and there is thus an urgent need for novel biomaterials as multifunctional constituents for dressings. A set of biocomposites was prepared by solvent casting using different concentrations of carboxymethylcellulose (CMC) and exfoliated graphene oxide (Exf-GO) as a filler. Exf-GO was first obtained by the strong oxidation and exfoliation of graphite. The structural, morphological and mechanical properties of the composites (CMCx/Exf-GO) were evaluated, and the obtained composites were homogenous, transparent and brownish in color. The results confirmed that Exf-GO may be homogeneously dispersed in CMC. It was found that the composite has an i…
Experimental Characterization of the Properties of Double-Lap Needled and Hybrid Joints of Carbon/Epoxy Composites
2015
The effect of through-thickness reinforcement by thin 1 mm steel needles (z-pins) on the static tensile strength of double-lap joints of a carbon/epoxy composite was investigated. Two types of joints—z-pinned and hybrid (including glued ones)—were considered. The joints were reinforced in the overlap region with 9, 25, or 36 z-pins. Comparing mechanical properties of the double-lap joints with the corresponding characteristics of their unpinned counterparts, the z-pins were found to be highly effective: the strength and stiffness of the pinned joints increased up to 300% and 280%, respectively. These improvements were due to a transition in the failure mechanism from debonding of the joint …
Diagnostic Performance and Radiation Dose of the EOS System to Image Enchondromatosis: A Phantom Study
2020
Background: Radiation doses and capability of EOS, conventional radiography (CR), and computed tomography (CT) to detect and measure enchondromas in a dedicated five-year-old anthropomorphic phantom were compared. Methods: To simulate enchondromas, minced pieces of chicken bone and cartilage were packed in conventional kitchen plastic foil to create ovoidal/rounded masses and randomly hung on the phantom. The phantom was imaged five times with CR, CT, and EOS, each time changing the number and position of inserts. All images were reviewed by a senior radiologist and a radiology resident. Results: EOS and CR detected all inserts in 4/5 cases (80%), while in one case 1/17 inserts was not seen…
Stainless steel grids for confinement of clay brick masonry columns
2016
This work presents the results of an experimental investigation on the behavior of 21 solid clay brick columns internally strengthened by stainless steel grids placed in the horizontal joints of mortar. This reinforcing technique can be applied as a constructive technique for new construction or as a retrofitting technique for existing structures (old structures to be reconstructed by original constructive method and internal reinforcement). Monotonic compressive loading tests were carried out under concentric and eccentric load. The effects of different numbers of steel grids and eccentricity of the external load were examined. Also, a detailed characterization of the constituent materials…
Computational Study of Failure of Hybrid Steel Trussed Concrete Beams
2017
This study investigates the failure behavior of hybrid steel trussed concrete beams (HSTCBs) under three-point bending through a series of finite-element (FE) simulations. The FE model employs well-established constitutive relations of concrete and steel with a simplified contact condition between the concrete and steel truss. The numerical model is compared with existing experimental data as well as a FE model that uses a more sophisticated concrete-steel interfacial model. The comparison shows that the present model is able to capture various failure mechanisms of the beam and its peak load capacity. The model is applied to investigate the behavior of a set of HSTCBs of different sizes, w…