Search results for "Civil Engineering"
showing 10 items of 1216 documents
Technological aspects regarding machining the titanium alloys by means of incremental forming
2017
Titanium alloys are materials with reduced formability, due to their low plasticity. However, today there are high demands regarding their use in the automotive industry and in bio-medical industry, for prosthetic devices. This paper presents some technological aspects regarding the machinability of titanium alloys by means of incremental forming. The research presented in this paper aimed to demonstrate that the parts made from these materials could be machined at room temperature, in certain technological conditions.
Influence of machining parameters on surface roughness in WEDM cutting
2020
Wire Electrical Discharge Machining is a cutting method used for obtaining parts with complex geometries or for cutting hard metals. This рарer ѕeekѕ to emрhаѕіze the іmрortаnce of thіѕ unconventіonаl technology аnd more ѕрecіfіcаlly the іmрortаnce of knowіng the раrаmeterѕ of а рroceѕѕ before рlаnnіng the рroductіon of а benchmаrk. Cylіndrіcаl metаl cаrbіde раrtѕ wіth а hаrdneѕѕ of 1620 HV / 92 HRC were cut durіng the analysis9, uѕіng the mіnіmum аnd mаxіmum vаlueѕ of the cutting раrаmeterѕ: wire feed rаte, wire rotаtіon ѕрeed, wіre tenѕіon, dіelectrіc рreѕѕure, electrіcаl current(Α) аnd electrіcаl рotentіаl (V). The roughneѕѕ of the obtаіned ѕurfаceѕ has been meаѕured after being cut аnd …
Comparative In Vitro Study of the Bond Strength of Composite to Carbon Fiber Versus Ceramic to Cobalt–Chromium Alloys Frameworks for Fixed Dental Pro…
2020
Purpose: The aim of this comparative in vitro study was to assess the bond strength and mechanical failure of carbon-fiber-reinforced composites against cobalt&ndash
Stress field model for strengthening of shear-flexure critical RC beams
2017
A model for the design of shear-flexure critical reinforced concrete elements strengthened with fiber-reinforced polymer (FRP) sheets and plates is presented. The model is based on the stress field approach and the equilibrium method and accounts for the different failure modes of FRP, focusing on the debonding of the FRP from the concrete surface. The efficiency of the model in the strength assessment of beams reinforced with FRP by the prediction of the shear-flexure capacity is checked by corroborating the results of several experimental tests found in the literature. Moreover, the presented model's capacity to reproduce experimental behavior is compared with the formulations suggested b…
Shear Capacity Model with Variable Orientation of Concrete Stress Field for RC Beams Strengthened by FRP with Different Inclinations
2021
A design-oriented analytical model able to evaluate the shear capacity of reinforced concrete (RC) beams strengthened with fiber-reinforced polymer (FRP) sheets or strips oriented in any direction is proposed. The formulation of the model is based on the variable-inclination stress-field approach, aiming to extend the provisions of current European standards to beams strengthened in shear using FRP. The main novelty of the model lies in taking into account the possible different inclination of steel stirrup and FRP reinforcement in determining the orientation of a compressed concrete stress field, and in shear strength evaluation, overcoming the approximation of the known models with variab…
Electrochemical discrimination of manufacturing types of pottery from Magna Mater Temple and Fora of Nerva and Caesar (Rome, Italy)
2018
Abstract The voltammetry of immobilized microparticles (VIMP) methodology is applied to a series of pottery samples from the Roman sites of Nerva's Forum (second half of 9th-early 11th A.D), Caesar's Forum (second half of 9th-early 11th A.D) and Magna Mater Temple (III century). The VIMP sampling applied to voltammetric and electrochemical impedance spectroscopy (EIS) measurements was applied by the first time to acquire archaeometric information on archaeological pottery. VIMP measurements using pressed sample pellets on gold electrodes in contact with air-saturated 0.10 M H2SO4 have permitted to detect voltammetric signals for the reduction/oxidation of Fe and Mn minerals as well as catal…
Ionic Nitriding of Certain Parts Protected on Nonfunctional Surfaces With Special Paints. Electric Energy Consumed
2021
The experimental researches on the promotion of new technologies for the local protection of metallic parts against plasma nitriding, led to two types of special paints for protection in ionic nitriding, paints elaborated on the basis of copper lamellar powder in combination with magnesium oxide and carbon tetrachloride. In the created context, it was considered that the elaborated paints could be used not only for preventing the hardening during ionic nitriding of certain technological surfaces of the parts on which they are applied, but also for coating certain nonfunctional surfaces, their degasification taking such a long time. These nonfunctional areas could be: surfaces resulted from …
Laboratory and in-situ tests for estimating improvements in asphalt concrete with the addition of an LDPE and EVA polymeric compound
2019
Abstract Pavement deformation is a critical issue in the design of pavement structures and the related mixture. Asphalt concretes may be very sensitive to this problem, in compliance with the viscoelastic behaviour of the adopted bitumen. To improve the material performance, many attempts have been made to introduce in the mixture other materials as “modifiers” or “additives” for increasing the permanent deformation resistance and the elastic modulus of the material. Among the different possible materials, polymers determined significant improvements in the road pavement performance. In this paper, the authors tested the adoption of a specifically engineered polymeric compound, in order to …
Raman Spectra of ZrS2 and ZrSe2 from Bulk to Atomically Thin Layers
2016
In the race towards two-dimensional electronic and optoelectronic devices, semiconducting transition metal dichalcogenides (TMDCs) from group VIB have been intensively studied in recent years due to the indirect to direct band-gap transition from bulk to the monolayer. However, new materials still need to be explored. For example, semiconducting TMDCs from group IVB have been predicted to have larger mobilities than their counterparts from group VIB in the monolayer limit. In this work we report the mechanical exfoliation of ZrX2 (X = S, Se) from bulk down to the monolayer and we study the dimensionality dependence of the Raman spectra in ambient conditions. We observe Raman signal from bul…
Review on Polymers for Thermoelectric Applications.
2014
In this review, we report the state-of-the-art of polymers in thermoelectricity. Classically, a number of inorganic compounds have been considered as the best thermoelectric materials. Since the prediction of the improvement of the figure of merit by means of electronic confinement in 1993, it has been improved by a factor of 3-4. In the mean time, organic materials, in particular intrinsically conducting polymers, had been considered as competitors of classical thermoelectrics, since their figure of merit has been improved several orders of magnitude in the last few years. We review here the evolution of the figure of merit or the power factor during the last years, and the best candidates…