Search results for "Combustion"
showing 10 items of 232 documents
A comparative economic analysis of torrefied pellet production based on state-of-the-art pellets
2017
Abstract Torrefied pellets have fuel properties superior to those of conventional wood pellets and potentially allow greater rates of co-firing and thus larger reductions in net CO 2 emissions. Despite the growing amount of scientific output on torrefaction, the economic feasibility of torrefied pellet production is still a topic of considerable uncertainty. This is an obstacle for decision makers looking to implement sustainable energy policies. This paper compares the economics of torrefied pellets to conventional wood pellets. Working backwards from demonstrated pellet properties, this work attempts to answer the following question: Based on state-of-the-art torrefied pellets, what would…
Photocatalytic Properties of Cement-Based Plasters and Paints Containing Mineral Pigments
2010
Innovative cement-based premix products for surface coating of buildings that possess photocatalytic activity arouse great interest because of the results they can achieve in reducting air pollution and maintaining aesthetics. This photoactivity is induced by a photocatalyst, titanium dioxide, that can accelerate the oxidation processes of air pollutants, particularly nitrogen oxides and volatile organic compounds, which are mainly produced by incomplete combustion of fuel and are present in urban environments through the exhaust gases of motor vehicles. Surfaces that are coated with these products acquire a self-cleaning characteristic (maintenance of original color) because the decomposi…
Total oxidation of naphthalene with high selectivity using a ceria catalyst prepared by a combustion method employing ethylene glycol.
2009
Abstract During the catalytic combustion of naphthalene, compounds other than CO 2 are often obtained. These products, as polymerized polycyclic aromatic hydrocarbons, oxygenated aromatic compounds and benzene derivate compounds, are usually more toxic than naphthalene. At the present work it is shown a nanocrystalline cerium oxide prepared by a combustion method employing a proper ethylene glycol concentration that exhibits very high activity in the decomposition of naphthalene in the presence of air and, most importantly, a selectivity value towards CO 2 of 100% for any range of conversions and/or temperatures used. In addition, it has been demonstrated that the amount of ethylene glycol …
A comparison between photocatalytic and catalytic oxidation of 2-Propanol over Au/TiO2-CeO2 catalysts
2016
Abstract Photocatalytic and catalytic oxidation of 2-propanol, representative of volatile organic compounds (VOC’s), were compared over mixed TiO 2 –CeO 2 -based catalysts. The effect of different amounts of CeO 2 and the presence of gold (1 wt%) on TiO 2 was investigated. In the photocatalytic oxidation CeO 2 had a negative effect on the performance towards the alcohol conversion of both TiO 2 –CeO 2 and Au/TiO 2 –CeO 2 catalysts, being Au/TiO 2 the most active system. On the contrary mixed TiO 2 –CeO 2 and Au/TiO 2 –CeO 2 samples showed a higher catalytic oxidation efficiency for 2-propanol conversion compared to the single oxides. In this case Au/CeO 2 catalyst had the best performance. …
Investigation on Ash Slagging Characteristics During Combustion of Biomass Pellets and Effect of Additives
2017
This study reports a systematic investigation into ash slagging behavior during combustion of barley straw and barley husk pellets with or without additives in a residential pellet burner. The slagging tendencies of the pellets were evaluated based on the amount, chemistry, mineralogy, and morphology of inlet ash formed as slag and sintering degrees of residual ash. The barley straw and husk pellets showed high slagging tendencies with 39 and 54 wt % ingoing ash formed as slag. Analyses using X-ray fluorescence and scanning electron microcopy combined with energy-dispersive X-ray spectroscopy revealed high concentrations of K, Si, and Ca but a minor amount of P in barley straw slag. The sla…
A POWERFUL TOOL TO STUDY COLLISIONAL PHENOMENA AND FOR COMBUSTION APPLICATIONS : THE HIGH RESOLUTION STIMULATED RAMAN SPECTROSCOPY
1987
Spray Atomization Models in Engine Applications, from Correlations to Direct Numerical Simulations
2011
Sprays are among the very main factors of mixture formation and combustion quality in almost every (IC) engine. They are of great importance in pollutant formation and energy efficiency although adequate modeling is still on development. For many applications, validation and calibration of models are still an open question. Therefore, we present an overview of existing models and propose some trends of improvement. Models are classified in zero dimensional and dimensional classes ranging from simple formulations aimed at close-to-real-time applications to complete detailed description of early atomization stages.
Cr(VI)/Cr(III) and As(V)/As(III) Ratio Assessments in Jordanian Spent Oil Shale Produced by Aerobic Combustion and Anaerobic Pyrolysis
2011
With the increase in the awareness of the public in the environmental impact of oil shale utilization, it is of interest to reveal the mobility of potentially toxic trace elements in spent oil shale. Therefore, the Cr and As oxidation state in a representative Jordanian oil shale sample from the El-Lajjoun area were investigated upon different lab-scale furnace treatments. The anaerobic pyrolysis was performed in a retort flushed by nitrogen gas at temperatures in between 600 and 800 °C (pyrolytic oil shale, POS). The aerobic combustion was simply performed in porcelain cups heated in a muffle furnace for 4 h at temperatures in between 700 and 1000 °C (burned oil shale, BOS). The high loss-…
Circulating fluidized bed reactors – part 01: analyzing the effect of particle modelling parameters in computational particle fluid dynamic (CPFD) si…
2019
A CPFD hydrodynamic model was developed for a circulating fluidized bed system and the simulation results were validated against experimental data based on particle circulation rate. Sensitivity of the computational mesh was primarily tested and extended grid refinement was needed at the loopseal to match the particle circulation rate with experimental data. The particle circulation rate was independent of the range of number of computational particles used in this study. A 10% reduction of the particle circulation rate was observed as the particle-wall interaction parameter was changed from 0.85 to 0.55 and 17% increment when the close-packed volume fraction was changed from 0.56 to 0.62. …