Search results for "Composite"
showing 10 items of 4584 documents
The influence of the tape-casting process parameters on the geometric characteristics of SiC tapes
1998
Abstract The production process of the tape-casting technique applied to the production of porous ceramic membranes, suitable for the separation of different chemical species, has been explored, with emphasis on the influence of the operative parameters on the macrogeometric characteristics of the manufactured ceramic porous tapes. The effects of the slurry casting rate, the doctor blade height and the mean particle diameter have been studied and the results reported. The characterization analyses indicate the degree of reliability of this technique to produce planar SiC components and the importance of the particle size in enhancing the structural homogeneity. A study on the variance analy…
Initial Preparation and Characterization of Single Step Fabricated Intermediate Temperature Solid Oxide Fuel Cells (IT-SOFC)
2013
In this study, facile tape casting process has been successfully carried out to fabricate an unit anode supported intermediate temperature solid oxide fuel cell (IT-SOFC) with four different layers: a composite cathode which is a mix of La0.6Sr0.4Co0.2Fe0.8O3 (LSCF48) and Gd0.1Ce0.9O1.9 (GDC10), GDC10 as thin electrolyte layer, NiO-GDC10 without pore former as thin anode functional layer (AFL), and anode support layer of NiO-GDC10 with carbon pore former. The multi-layer was sintered once to produce an unit planar cell. An OCV of 1.002 V at 500 °C, and maximum power density of 466 mW cm–2 at 648 °C are obtained. These results indicate negligible leakage of fuel through electrolyte. Furtherm…
Film blowing of silane-modified polyethylene
2009
The grafting of vinyltriethoxysilane (VTES) onto polyethylene (PE) with the help of small amounts of peroxides was investigated to film-blow these modified materials. The degree of crosslinking was kept very low to achieve good melt processability and improved mechanical properties. The possibility of obtaining modified PE films with improved properties and regularly distributed crosslinking with a single processing step demonstrates the uniqueness of this study. The additive concentration was established through preliminary studies; with a batch mixer, it was possible to process the modified PE in the film-blowing operation. Water treatment of the modified films after film blowing allowed …
Structure-property relationships of polycarbonate diol-based polyurethanes as a function of soft segment content and molar mass
2014
Segmented thermoplastic polyurethanes (PUs) have been synthesized with polycarbonate diol as soft segment and 4,4′-diphenylmethane diisocyanate and butanediol as hard segment. Two different series employing two different soft-segment molar mass, 1000 and 2000 g/mol, and by changing the hard-segment content from 32 to 67% have been investigated with the aim to elucidate the effect of the different content variations on the properties. Morphological, thermal, and mechanical properties have been studied by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), wide angle X-ray diffraction, atomic force microscopy, tensile and…
Interfacial Self-Assembly to Spatially Organize Graphene Oxide Into Hierarchical and Bioactive Structures
2020
Multicomponent self-assembly holds great promise for the generation of complex and functional biomaterials with hierarchical microstructure. Here, we describe the use of supramolecular co-assembly between an elastin-like recombinamer (ELR5) and a peptide amphiphile (PA) to organize graphene oxide (GO) flakes into bioactive structures across multiple scales. The process takes advantage of a reaction—diffusion mechanism to enable the incorporation and spatial organization of GO within multiple ELR5/PA layers. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ImageJ software were used to demonstrate the hierarchical organization of GO flakes within the ELR5/PA lay…
Benchmarking of strength models for unidirectional composites under longitudinal tension
2018
© 2018 Elsevier Ltd Several modelling approaches are available in the literature to predict longitudinal tensile failure of fibre-reinforced polymers. However, a systematic, blind and unbiased comparison between the predictions from the different models and against experimental data has never been performed. This paper presents a benchmarking exercise performed for three different models from the literature: (i) an analytical hierarchical scaling law for composite fibre bundles, (ii) direct numerical simulations of composite fibre bundles, and (iii) a multiscale finite-element simulation method. The results show that there are significant discrepancies between the predictions of the differe…
MoSi2 laser cladding—a comparison between two experimental procedures: Mo–Si online combination and direct use of MoSi2
2001
International audience; There are very strong interests in developing low density advanced material systems for service at temperatures up to 1300°C. These materials should mainly have moderate fracture toughness at low and intermediate temperatures and should exhibit oxidation resistant behaviour. The intermetallic compound, MoSi2 has been considered to be an attractive candidate due to its melting point (2030°C) and excellent oxidation resistance at high temperatures. In this paper, we compare the results obtained with two different techniques for laser cladding, one using an online combination between Mo and Si powders, the second using direct injection of the MoSi2 powder.
Mechanical and Thermal Properties of Insulating Sustainable Mortars with Ampelodesmos mauritanicus and Pennisetum setaceum Plants as Aggregates
2021
The use of natural fibers in cement composites is a widening research field as their application can enhance the mechanical and thermal behavior of cement mortars and limit their carbon footprint. In this paper, two different wild grasses, i.e., Ampelodesmos mauritanicus, also called diss, and Pennisetum setaceum, also known as crimson fountaingrass, are used as a source of natural aggregates for cement mortars. The main purpose is to assess the possibility of using the more invasive crimson fountaingrass in place of diss in cement-based vegetable concrete. The two plant fibers have been characterized by means of scanning electron microscopy (SEM), helium picnometry and thermogravimetric an…
Impact of Si on the high-temperature oxidation of AlCr(Si)N coatings
2022
The resistance of wear protective coatings against oxidation is crucial for their use at high temperatures. Here, three nanocomposite AlCr(Si)N coatings with a fixed Al/Cr atomic ratio of 70/30 and a varying Si-content of 0 at.%, 2.5 at.% and 5 at.% were analyzed by differential scanning calorimetry, thermogravimetric analysis and X-ray in order to understand the oxidation behavior depending on their Si-content. Additionally, a partially oxidized AlCrSiN coating with 5 at.% Si on a sapphire substrate was studied across the coating thickness by depth-resolved cross-sectional X-ray nanodiffraction and scanning trans-mission electron microscopy to investigate the elemental composition, morphol…
A model of oil burnout from glass fabric
1997
A mathematical model is proposed for the process of the removal (by burning) of oil contained in a glass fibre insulation fabric manufactured in Latvia. The small aspect ratio of the fabric allows simplifications to the modelling which reduce the problem to a single nonlinear ordinary differential equation. When the effects of reflected radiation are also included, the differential equation is supplemented by two integral equations. Predictions of the position of the ‘burning zone’ accord well with observations made at the factory. The effect of the inclusion of extra heating chambers is also examined, and it is found that the temperature gradient in the fabric may be greatly decreased in t…