Search results for "Composite"
showing 10 items of 4584 documents
Influence of process parameters for thixotropic alloys
2007
With reference to a metallic alloy, the attribute thixotropic is utilized to indicate the behaviour of it in the semi-solid state when its microstructure consists of spheroids in a liquid matrix. Such alloys are characterized by very low values of viscosity under shearing stress in the semi-solid state, while after solidification they show relevant mechanical properties. Actually a structural change from a dendritic structure to a globular one, with the globular grains finely dispersed in a liquid matrix, is observed after particular thermo-mechanical treatments. In the present paper the authors present the results of a wide experimental campaign on the AA 7075 aluminium alloy that shows a …
Three-dimensional analysis of load transfer micro-mechanisms in fibre/matrix composites
2009
International audience; This study gives a detailed analysis of load distributions around fibre breaks in a composite. In contrast to other studies reported in the literature, the analysis considers different configurations of composite damage from the failure of a few to the failure of many fibres. The model considers three types of matrix behaviours (elastic, elastic–plastic and viscoelastic) with or without debonding at the broken fibre/matrix interface. In this way, the usual limitations of the finite element approach are overcome so as to take into account the number and interactions of broken fibres whilst maintaining an evaluation of the various fields (stresses in particular).
Experimental Investigation of the Shear Response of Precast Steel-Concrete Trussed Beams
2017
The results of an experimental campaign of three-point bending tests on precast composite beams, named hybrid steel-trussed concrete beams (HSTCBs), are provided. HSTCBs are typically constituted by a precast steel truss embedded in a block of concrete cast in place. Two series of specimens were manufactured, designed such that shear failure would occur, and tested under positive and negative bending moment. The experimental results obtained showed that fragile shear failure occurred in almost all cases, evidencing the crisis of the compressed concrete strut involved in the collapse mechanism. Yielding of the steel members provided ductility to the system, especially in those cases in which…
Supercritical carbon dioxide extraction of seed oil from yellow horn (Xanthoceras sorbifolia Bunge.) and its anti-oxidant activity
2010
Supercritical fluid carbon dioxide (SF-CO(2)) extraction (SFE) of seed oil from yellow horn and its anti-oxidant activity were investigated. The effects of CO(2) flow rate and particle size were firstly optimized, and a central composite design (CCD) combined with response surface methodology was used to study the effects of extraction pressure, temperature and time on the extraction yields. A maximal extraction yield of 61.28% was achieved under optimal conditions of extraction pressure 30 MPa at 45.68 degrees C, 2.08 h and CO(2) flow rate 12 kg/h with 0.5mm particle size. By analyzing the chemical composition of the seed oil, we found that the content of unsaturated fatty acids was approx…
In vitro degradation of porous PLLA/pearl powder composite scaffolds
2013
Abstract The in vitro degradation behavior of poly- l -lactide (PLLA), PLLA/aragonite pearl powder and PLLA/vaterite pearl powder scaffolds was investigated. The scaffolds were soaked in phosphate buffer solution (PBS) up to 200 days. Scanning electron microscopy (SEM), gel permeation chromatography (GPC), and differential scanning calorimetry (DSC) were used to observe any degradation of the scaffolds. Degradation behaviors such as changes in pH, porosity, bulk density, water absorption, weight loss and mechanical properties were discussed. The results show that a gradual increase of the pH in composite scaffolds can decrease the rate of hydrolysis of PLLA. PLLA/vaterite and PLLA/aragonite…
Acoustic methods for measuring the porosities of porous materials incorporating dead-end pores
2013
International audience; The acoustic properties of porous materials containing dead-end (DE) pores have been proposed by Dupont et al. [J. Appl. Phys. 110, 094903 (2011)]. In the theoretical description, two physical parameters were defined (the dead-end porosity and the average length of the dead-end pores). With the knowledge of the open porosity (measured with non-acoustic methods), and the measurement of kinematic porosity (also called the Biot porosity in this article), it is possible to deduce the dead-end porosity. Two acoustic methods for measuring the Biot porosity for a wide range of porosities are proposed. These methods are based on acoustic transmission and on the low and high …
Short‐term hypoxia promotes vascularization in co‐culture system consisting of primary human osteoblasts and outgrowth endothelial cells
2019
Prevascularization of tissue constructs before implantation has been developed as a novel and promising concept for successful implantation. Since hypoxia might induce angiogenesis, we have investigated the effects of hypoxic treatment on vascularization by using co-cultures of primary human osteoblasts (POBs) and outgrowth endothelial cells. Our results show that: (a) repeated short-term hypoxia (2% O2 for 8 hr), not long-term hypoxia (2% O2 for 24 hr), over 1 or 2 weeks, significantly enhances microvessel formation in co-cultures; (b) sustained hypoxia, not short-term or long-term hypoxia, causes cytotoxicity in mono- and co-cultures; (c) the expression of some angiogenic and inflammatory…
Cariostatic effect of a light-cured, resin-reinforced glass-ionomer for bonding orthodontic brackets in vivo
1998
The aim of this study was to evaluate in vivo the cariostatic potential of the resin-reinforced glass-ionomer (Vitremer core build-up restorative; 3M Dental Product Division) when used as a bonding agent for orthodontic brackets. The mineral distribution and topography of the enamel surface adjacent to the bracket base was determined by quantitative microradiography (TMR) and confocal laser scanning microscopy (CLSM). The study was designed in split-mouth technique using 9 pairs of premolars to be extracted for orthodontic reasons. One tooth of each pair was bonded with the resin-reinforced glass-ionomer, and the control contralateral premolar with the non-fluoridated composite (Concise, 3M…
Minimal exposure time of different LED-curing devices
2007
Abstract Objectives The purpose of the study was to investigate the shortest possible exposure time of different LED-curing devices for five different resin composites in a clinically relevant in vitro-model, where a 7 mm distance from the light guide tip to the bottom side of the cavity was compiled. Methods Resin composite samples (Tetric EvoCeram A3, Filtek Supreme XT A3B, Premise A3, CeramX Mono M5, QuiXfil) were filled in three increments of 2 mm thickness each in stainless steel moulds (O = 5 mm, h = 6 mm, n = 9). The samples were incrementally exposed to different blue LED-curing devices (Bluephase, Bluephase C8, Bluephase 16i/Ivoclar Vivadent, L.E.Demetron II/sds Kerr, Elipar Free…
An analytical solution for multilayered beams subjected to ends loads
2014
An alternative model for multilayered beams undergoing axial, shear and bending loads applied at the beam's ends is developed. It is based on a layer-wise kinematics, which inherently fulfills the equilibrium equations at layer level and the interface continuity conditions. This kinematics is suitably expressed by introducing a set of generalized variables representative of the beam midline displacement field, which become the primary variables of the problem governing equations. As a consequence, the proposed beam model exhibits the computational characteristics of an equivalent single layer model and possesses the accuracy of layer-wise beam theories, as well. Closed form solutions for di…