Search results for "Compres"
showing 10 items of 1107 documents
Compressive behaviour of laminated structural glass members
2011
Abstract Several experimental investigations in the past few years have highlighted the fact that the compressive strength of glass was significantly higher than its tensile strength, allowing new applications of glass in compression members. However, due to the high slenderness of structural glass elements made of thin glass panels, they tend to fail in a brittle manner. A substantial amount of fundamental research has been carried out in the past few years to investigate the stability behaviour of structural glass elements. However, although buckling of glass panels has been quite well studied, a very poor amount of research has been addressed to glass columns, which by contrast represent…
Mix design and mechanical performance of geopolymeric binders and mortars using biomass fly ash and alkaline effluent from paper-pulp industry
2019
Abstract This work investigates the use of biomass fly ash (BFA) and an alkaline effluent (AEF), both generated from the Kraft pulp industry, in the preparation of geopolymeric binders and mortars for construction applications. BFA replaced the metakaolin (MK) while the AEF substituted the distilled water used to dissolve NaOH pellets. The mix design aims to maximize the amount of both the wastes and to optimize the materials properties, such as workability and mechanical performance. At the same time, also the environmental impact decreases enhancing the materials' sustainability and facilitating the circular economy. For the previously optimized BFA/MK ratio (70/30 wt.%) several NaOH/Na2S…
Experimental study of stress-relaxation behaviour of polycarbonate after yielding
1981
The viscoelastic behaviour of a bisphenol A polycarbonate after yielding is described by means of empirical superposition of coordinates along both time and stress axis, which allow collecting stress relaxation data, taken both in tension and in compression, into a master curve.
Improvements in aggregate-paste interface by the hydration of steelmaking waste in concretes and mortars
2019
[EN] The objective of the experimental work is to study the mechanical properties in self-compacting concretes (SCC) in which part of the limestone aggregate has been replaced by granulated blast furnace slag (GBFS) in different percentages ranging from 0% to 60%. The results show that at early ages the SCC with the largest content in slag tend to have lower compressive strengths due to the poor compacting of the aggregates, although in the long-term their strength increases due to the reactivity of the slag. In fact, at the age of 365 days, the mortars made with the substitution of 50% of cement by ground GBFS reach compressive strength similar to that of the mortar made with 100% of cemen…
Preformulation: Effect of Moisture Content on Microcrystalline Cellulose (Avicel PH-302) and Its Consequences on Packing Performances
1999
This study evaluates the influence of moisture content on the packing performances of a new grade of microcrystalline cellulose (MCC) (Avicel PH-302) either by classical method or by an unconventional compression technique (constant volume reduction of powder bed). An increase in moisture content decreases the apparent density of the powder bed, resulting from interparticulate friction enhancement. This modification of apparent density seems to be the main effect caused by the presence of humidity, which explains the variations of compression properties, like an increase of powder plasticity generally observed in the experimental conditions.
Collapsible intact soil stabilisation using non-aqueous polymeric vehicle
2020
Abstract This paper presents the results of an experimental study that had the goal of understanding the effects of treatment with polyethylene glycol (PEG)/nanolime mixtures on collapsible soil behaviour. In a previous study, the use of pure PEG offered a good improvement in the stability of collapsible soil, but the stabilisation effect only lasted for a limited time. To investigate the stabilisation potential of PEG/nanolime systems for collapsible sand, different mixtures were prepared at increasing nanolime weight ratios. The suitability of the stabilised soil was examined on the basis of collapsibility, oedometer, shear, and water vapour permeability tests, and through optical microsc…
Impact behaviour of flax/epoxy composite plates
2015
This paper presents an experimental investigation of the impact behaviour of flax/epoxy composite plates submitted to low-velocity transverse impact. Low energy drop-weight impact tests have been performed on two types of quasi-isotropic flax/epoxy composites, rectangularly shaped with edges lengths of 142 mm × 94 mm and 2.85 mm thick. Residual properties have been assessed by compression after impact tests. A detailed description of damage development, especially the increase of the rear face crack with respect to the impact energy is given by the microscopic observation. The influence of impact damage on the residual strength is described. A loss of 15%–30% in compression resistance was n…
Mechanical behavior of polylactic acid/polycaprolactone porous layered functional composites
2016
Abstract Biopolymeric porous devices exhibiting graded properties can play a crucial role in several fields, such as tissue engineering or controlled drugs release. In this context, the gradient of a specific property can be achieved by developing porous laminates composed by different types of materials. This work presents for the first time a multi-phasic porous laminate based on polycaprolactone (PCL) and polylactic acid (PLA) prepared by combining melt mixing, compression molding and particle leaching. All the materials were characterized from a morphological and a mechanical point of view. The results put into evidence the possibility to tune and to predict the mechanical properties by…
Comparative study of the lubricant performance of Compritol 888 ATO either used by blending or by hot melt coating.
2003
Compritol 888 ATO is used as a lubricant in oral solid dosage formulations. It can also be used as a hot melt coating agent sprayed onto a powder. In this study, we compare the lubricant performance of Compritol 888 ATO either used by classical blending or by hot melt coating onto Lactopress by compression tests. In physical mix, the Compritol concentration does not affect the compressibility. The same compressibility is obtained with lactose coated by 0.5 or 1% of Compritol, but a higher compressibility can be observed with 2 and 3%. Cohesiveness of lactose depends on the process: hot melt coating induces a decrease of tablet tensile strength. In terms of forces transmission during compres…
Scaffolds based on hyaluronan crosslinked with a polyaminoacid: Novel candidates for tissue engineering application
2008
New porous scaffolds, with a suitable hydrolytic and enzymatic degradation, useful for tissue engineering applications have been obtained by a carbodiimide mediated reaction between hyaluronan (HA) and a synthetic polymer with a polyaminoacid structure such as α,β-polyaspartylhydrazide (PAHy). Scaffolds with a different molar ratio between PAHy repeating units and HA repeating units have been prepared and characterized from a chemical and physicochemical point of view. Tests of indirect and direct cytotoxicity, cell adhesion, and spreading on these biomaterials have been performed by using murine L929 fibroblasts. The new biomaterials showed a good cell compatibility and ability to allow ce…