Search results for "Computer Science Application"
showing 10 items of 3998 documents
Molecular Endocrinology and Metabolism in 2021: What’s New
2021
The last two years, despite the very serious COronaVIrus Disease-2019 (COVID-19) pandemic, have been quite productive in the field of molecular endocrinology and metabolism and our journal section has contributed extensively on that [...]
Numerical Simulations of the Hydrodynamics of the Abdominal Aorta Aneurysm (AAA) Using a Smoothed Particle Hydrodynamics Code with Deformable Wall Pr…
2018
We present some preliminary results of the numerical simulations of the hydrodynamic characteristics of an abdominal aorta aneurysm (AAA) patient specific test case. Images of the AAA lumen have been acquired in 10 discrete time-steps through a stabilized cardiac cycle by electrocardiogram-gated computer tomography angiography, and are used to approximate the in vivo, time dependent kinematic fields of the (internal) arterial wall. The flow field is simulated by a Smoothed Particle SPH numerical model, where the kinematics of the boundary of the computational domain (the internal aortic vessel) is the one computed by the above procedure. The outputs of the SPH model, i.e., pressure and flow…
TRANSIENT SEMICONDUCTOR DEVICE SIMULATION INCLUDING ENERGY BALANCE EQUATION
1992
An efficient numerical method for the solution of hot‐carrier transport equations describing transient processes in submicrometer semiconductor devices is proposed. The calculations of transient processes in submicrometer MOS transistor were carried out and compared with the results obtained by conventional drift‐diffusion model.
Special Section Guest Editorial:Special Section on Quality Control by Artificial Vision: Nonconventional Imaging Systems
2015
This PDF file contains the editorial “Special Section Guest Editorial:Special Section on Quality Control by Artificial Vision: Nonconventional Imaging Systems” for JEI Vol. 24 Issue 06
Special Section on Quality Control by Artificial Vision
2008
This PDF file contains the editorial “Editorial: Special Section on Quality Control by Artificial Vision” for JEI Vol. 17 Issue 03
Thermophysical-Property-Based Selection of Tool Protective Coatings for Dry Machining of Steels
2003
A method is proposed for determining the optimum cutting conditions in dry turning of carbon and stainless steels using multilayer coated tools for physical criteria such as the maximum temperature of a cutting tool or maximum heat flux. The modified thermal number describing the tool-chip behavior, is introduced. The correlation between the thermal number and the average tool-chip interface temperature and frictional heat flux is examined for both flat-faced and grooved rake configurations. Although not shown here directly, the thermal barrier effect observed for multilayer coatings with an intermediate Al2O3 layer increases the heat partition to the chip at substantially reduced cutting t…
Computer-assisted orientation and drawing of archaeological pottery.
2018
Archaeologists spend considerable time orienting and drawing ceramic fragments by hand for documentation, to infer their manufacture, the nature of the discovery site and its chronology, and to develop hypotheses about commercial and cultural exchanges, social organisation, resource exploitation, and taphonomic processes. This study presents a survey of existing solutions to the time-consuming problem of orienting and drawing pottery fragments. Orientation is based on the 3D geometry of pottery models, which can now be acquired in minutes with low-cost 3D scanners. Several methods are presented: they are based on normal vectors, or circle fittings, or profile fittings. All these methods see…
Part program automatic check for three axis CNC machines
2001
Abstract The simulation and verification of NC codes for CNC machining is a very important task. The aim of this work is to limit the number of cutting tests needed to verify the right writing of the part program for a CN milling machine in the intent of saving time, human resources and money. This is obtained through the Boolean operation among solids, in AutoCAD environment, of the volume covered by the tool during the operations ruled by the part program.
Finite element modelling of temperature distribution in the cutting zone in turning processes with differently coated tools
2005
Abstract The aim of this study is to check the applicability of various simulation models to obtain finite element solutions of cutting forces, specific cutting energy and adequate temperatures for a range of coated tool materials and defined cutting conditions. Commercial explicit finite element code Thirdwave AdvantEdge has been used in simulations of orthogonal cutting processes performed by means of uncoated carbide and coated tools. The latter were equipped with progressively increasing number of thin layers including TiC, TiN and Al 2 O 3 films deposited onto ISO P20 carbide substrates. Results showing the tool–chip interfacial friction influencing the temperature distribution fields,…
Intelligent robotic cell for Trencad/spl inodot//spl acute/s mosaics manufacturing
2005
The purpose of this paper is the description of an application for the complete automation of a mosaics manufacturing process with irregular random pieces, so called trencad/spl inodot//spl acute/s. An intelligent robotic cell has been implemented by using intelligent methods and pattern recognition techniques to assemble unpredictable objects in an autonomous manner.