Search results for "Deposit"
showing 10 items of 1447 documents
Analysis of Organic Aerosols Using a Micro-Orifice Volatilization Impactor Coupled to an Atmospheric-Pressure Chemical Ionization Mass Spectrometer
2014
We present the development and characterization of a combination of a micro-orifice volatilization impactor (MOVI) and an ion trap mass spectrometer (IT/MS) with an atmospheric-pressure chemical ionization (APCI) source. The MOVI is a multi-jet impactor with 100 nozzles, allowing the collection of aerosol particles by inertial impaction on a deposition plate. The pressure drop behind the nozzles is approximately 5%, resulting in a pressure of 96 kPa on the collection surface for ambient pressures of 101.3 kPa. The cut-point diameter (diameter of 50% collection efficiency) is at 0.13 μm for a sampling flow rate of 10 L min–1. After the collection step, aerosol particles are evaporated by he…
Accounting meets economics: towards an ‘accounting view’ of money.
2018
Questo studio pone le fondamenta dell’ “Approccio Contabile” (“Accounting View”) alla moneta. Sulla base dei principi di Ragioneria Generale riconosciuti internazionalmente, lo studio argomenta che le monete emesse dallo stato e dalla banca centrale non costituiscono debito e che nei regimi di riserva frazionaria soltanto una quota della moneta emessa dalle banche commerciali pu essere considerata quale debito. Lo studio chiarisce come il signoraggio associato all’emissione di queste monete debba essere contabilizzato nei bilanci delle istituzioni emittenti ed esamina le implicazioni di ci`o per la corretta comprensione della moneta. Il nuovo approccio fa luce su argomenti quali la vera nat…
Platinum-doped CeO2 thin film catalysts prepared by magnetron sputtering.
2010
The interaction of Pt with CeO(2) layers was investigated by using photoelectron spectroscopy. The 30 nm thick Pt doped CeO(2) layers were deposited simultaneously by rf-magnetron sputtering on a Si(001) substrate, multiwall carbon nanotubes (CNTs) supported by a carbon diffusion layer of a polymer membrane fuel cell and on CNTs grown on the silicon wafer by the CVD technique. The synchrotron radiation X-ray photoelectron spectra showed the formation of cerium oxide with completely ionized Pt(2+,4+) species, and with the Pt(2+)/Pt(4+) ratio strongly dependent on the substrate. The TEM and XRD study showed the Pt(2+)/Pt(4+) ratio is dependent on the film structure.
Growth and composition of nanostructured and nanoporous cerium oxide thin films on a graphite foil.
2015
The morphology and composition of CeOx films prepared by r.f. magnetron sputtering on a graphite foil have been investigated mainly by using microscopy methods. This study presents the formation of nanocrystalline layers with porous structure due to the modification of a carbon support and the formation of cerium carbide crystallites as a result of the deposition process. Chemical analyses of the layers with different thicknesses performed by energy dispersive X-ray spectroscopy, electron energy loss spectroscopy and X-ray photoelectron spectroscopy have pointed to the reduction of the cerium oxide layers. In the deposited layers, cerium was present in mixed Ce(3+) and Ce(4+) valence. Ce(3+…
Pt–CeO thin film catalysts for PEMFC
2015
Abstract Platinum is the mostly used element in catalysts for fuel cell technology, but its high price limits large-scale applications. Platinum doped cerium oxide represents an alternative solution due to very low loading, typically few micrograms per 1 cm2, at the proton exchange membrane fuel cell (PEMFC) anode. High efficiency is achieved by using magnetron sputtering deposition of cerium oxide and Pt of 30 nm thick nanoporous films on large surface carbon nanoparticle substrates. Thin film techniques permits to grow the catalyst film characterized by highly dispersed platinum, mostly in ionic Pt2+ state. Such dispersed Pt species show high activity and stability. These new materials ma…
Proton exchange membrane fuel cell made of magnetron sputtered Pt–CeO and Pt–Co thin film catalysts
2015
Abstract Preparation of catalysts for proton exchange membrane fuel cells (PEMFCs) is of growing interest during last years. The magnetron sputtering technique is a promising method of catalyst preparation because it permits to synthesize catalysts in a fast and relatively less expensive way, however control of specific surface and durability of such catalysts still remains the main concern. We tested a single cell PEMFC catalyzed by using exclusively thin film approach by combining state-of-the art Pt-doped cerium oxide anode and a new Pt–Co alloy cathode. We have shown that beside very high mass activity of the catalysts relative to the membrane electrode assembly the catalyst nanoporous …
Preparation of magnetron sputtered thin cerium oxide films with a large surface on silicon substrates using carbonaceous interlayers.
2013
The study focuses on preparation of thin cerium oxide films with a porous structure prepared by rf magnetron sputtering on a silicon wafer substrate using amorphous carbon (a-C) and nitrogenated amorphous carbon films (CNx) as an interlayer. We show that the structure and morphology of the deposited layers depend on the oxygen concentration in working gas used for cerium oxide deposition. Considerable erosion of the carbonaceous interlayer accompanied by the formation of highly porous carbon/cerium oxide bilayer systems is reported. Etching of the carbon interlayer with oxygen species occurring simultaneously with cerium oxide film growth is considered to be the driving force for this effec…
MOCVD growth of porous cerium oxide thin films on silicon substrate
2015
Abstract Porous cerium oxide thin films were grown by pulsed direct liquid injection metal organic chemical vapor deposition (DLI-MOCVD) on silicon substrate, using cerium tetrakis (1-methoxy-2-methyl-2-propanolate) dissolved in cyclohexane as precursor as well as oxygen as oxidant agent. The chemical and morphological characteristics of the films were investigated by XPS, SEM and TEM. The influence of the growth conditions on the morphological features of the thin films and the cerium chemical states are reported and discussed. The decrease of the oxygen and/or alkoxide flow rate induces the decrease of both the film thickness and the porosity of the layer. Moreover, the growth of silicate…
The synthesis of zeolites from dry powders
1995
Summary ZSM-5 was synthesized by different methods with a gradually decreasing water content ending in a reaction mixture with absolutely dry reagents in form of a powder in the complete absence of a solution phase. Amorphous precursors obtained by drying SiO 2 * Al 2 O 3 gels at 650°C were transformed into zeolites in the presence of dried NH 4 F and TPABr. The reaction products were characterized by XRD, REM, TG/DTA, MAS NMR and Electron Micropobe. Pure ZSM-5 or Silicalite-1 was obtained in all cases. Some water is probably formed as a reaction product, but the maximum water pressure is appreciably below the saturation pressure at the given reaction conditions. To explain the formation of…
Chemical Vapour Deposition of Pure Titanium Using a Heated Wire Reactor and TiI4
2017
Master's thesis Renewable Energy ENE500 - University of Agder 2017 An experimental reactor system has been optimized throughout a series of experiments for making titanium tubes from an electrically heated titanium coil filament by a chemical vapour deposition method, based on the original van Arkel-de Boer -process. The titanium is thermally decomposed on the filament from vapourized titanium tetraiodide in a method not seen in similar experiments. The small-scale reactor is built for this purpose, and the associated systems and methods are developed to maintain the optimal conditions for a continuous metal deposition. A filament current control system is made of an Arduino micro-controlle…