Search results for "Diss"
showing 10 items of 2500 documents
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
From ZIF-8@Al2O3Composites to Self-Supported ZIF-8 One-Dimensional Superstructures
2015
International audience; Efficient preparation of composite materials consisting of ZIF-8 nanocrystals embedded inside the channels of macroporous anodic aluminum oxide membranes is reported. 1-D self-supported ZIF-8 superstructures are recovered through matrix dissolution.
Diffusion of oxygen molecules in fluorine-doped amorphous SiO2
2010
Abstract Effects of fluorine doping on the diffusion of interstitial oxygen molecules (O2) in amorphous SiO2 (a-SiO2) were compared to those obtained from a-SiO2 containing SiOH groups. Incorporation of moderate concentration ( ∼ 1 0 19 cm−3) of SiF groups gives rise to minor changes in diffusion parameters between 800 and 1100 ° C: only a slight decrease in solubility and an increase in the activation energy for diffusion can be detected. Incorporation of SiOH groups has similar weak effects on the solubility and activation energy for diffusion. These minor changes are most likely due to the enhancement of the flexibility of local Si–O network as a result of the dissociation of the netwo…
Characteristics of mechanical metamaterials based on buckling elements
2017
Metamaterials are composed of structural elements and derive their properties mainly from the inner structure of the elements, rather than the properties of their constituent material. By designing an unstable structural element as the building block of a metamaterial, many interesting effective material properties can be obtained. The deformation and dissipation mechanisms of such a material built from unstable structural elements is studied in detail. To do so a combination of analytical, semi-analytical, and numerical models are applied to a single buckling element, a periodic cell, and finite size combinations of buckling elements including gradients in the properties of the building bl…
Dynamical behaviour of pneumatic artificial muscles
2014
The mechanical response of pneumatic artificial muscles is analyzed in transient and periodic conditions, assuming the inextensibility of the sheathing fibres and considering the influence of the texture geometry, of the dissipation due to the mutual sliding between the braids and of the stress field inside the bladder thickness, where the constituent elastomer is regarded as a two-parameter Mooney–Rivlin material. The polytropic exponent of the thermodynamic air evolution inside the muscle during the charging and discharging phases may be properly chosen depending on the working frequency. The muscle end shape is taken into account profiling the meridian section by a simple m-degree parabo…
Microstructural corrosion of aluminium alloys: a predictive finite element model based on corrosion-mimicking experiments
2013
The purpose of this study is to implement the basis of a finite element model (FEM) based on the resolution of the Nernst–Planck equation in order to progress in the predictive simulation of microstructural corrosion on aluminium alloys. Certain constituent intermetallic particles at the surface of aluminium alloys are considered as preferential sites for the initiation of structural corrosion resulting in localised trenching around the particles and the surrounding Al matrix. In this work, a modified scanning electrochemical microscope (SECM) experiment was used to induce such phenomena via a local alkalinization on 200 nm thick aluminium coatings, promoting their local dissolution in an a…
Anisotropic flow in striped superhydrophobic channels
2012
We report results of dissipative particle dynamics simulations and develop a semi-analytical theory of an anisotropic flow in a parallel-plate channel with two superhydrophobic striped walls. Our approach is valid for any local slip at the gas sectors and an arbitrary distance between the plates, ranging from a thick to a thin channel. It allows us to optimize area fractions, slip lengths, channel thickness and texture orientation to maximize a transverse flow. Our results may be useful for extracting effective slip tensors from global measurements, such as the permeability of a channel, in experiments or simulations, and may also find applications in passive microfluidic mixing.
Simulation of pH-controlled dissolution of aluminium based on a modified Scanning Electrochemical Microscope experiment to mimic localized trenching …
2011
Abstract Some constituent intermetallic (IMPs) particles at the surface of aluminium alloys are considered as preferential sites for the initiation of structural corrosion resulting in localized trenching around the particles and the surrounding Al matrix. In this work, a modified scanning electrochemical microscope (SECM) experiment was used to induce such phenomena via a local alcalinisation on 200 nm thick aluminium coatings promoting their local dissolution in an aerated 0.1 M NaCl electrolyte. The local alcalinisation was induced by the oxygen reduction reaction on the tip of a SECM which mimics the surface of an isolated IMP. From a phenomenological point of view, reproducible cylindr…
Electrogeneration of Diiodoaurate in Dimethylsulfoxide on Gold Substrate and Localized Patterning
2016
International audience; A localized etching of gold surface by scanning electrochemical microscope technique is presented where a dimethylsulfoxide-based electrolyte charged with iodine is used. The electrogenerated triiodide ion at the platinum ultramicroelectrode tip (feedback mode) acts as an oxidant for gold surface. The effects of electrode diameter and the bias time have been investigated. The approach curve method was used to hold the electrode tip close to the gold surface. A scanning electron microscope is used to observe the etched gold surfaces where disk-shaped dots are generated. The diameter of these holes depends directly on the Pt electrode diameter and the bias time.
Study of Morphology of Reactive Dissolution Interface Using Fractal Geometry
1996
J. Pharm. Sci. ISI Document Delivery No.: VF662 Times Cited: 7 Cited Reference Count: 15 Tromelin, A Gnanou, JC Andres, C Pourcelot, Y Chaillot, B; International audience; The determination of reactive fractal dimension was carried out using two forms of the Noyes-Whitney equation, -dQ/dt = K(Q/Q(0))(DR/3) and -d Q/dt = K' R(DR-3) using the Richardson plot on the basis of previous data obtained by dissolution of an orthoboric acid powder. The correlation of the results provided by the two ways of calculation allows proposal of the hypothesis that dissolution begins on a specific population of reactive sites and probably promotes the formation of microporous volumes or cracks.