Search results for "ELEMENT"
showing 10 items of 13601 documents
Determination of an empirical law of aluminium and magnesium alloys absorption coefficient during Nd :YAG laser interaction
2007
International audience; Welding laser modelling requires knowledge about relative changes of many thermo-physical parameters involved in the interaction. The absorptivity of the material is one of the most important. In this study, experimental measurements of absorptivity with an integrating sphere on two alloys (aluminium and magnesium) were made. These results were compared with an analytical calculation that takes into account the trapping of the beam by multiple reflections inside the keyhole. Based on a statistical method, an empirical law is proposed connecting absorptivity with the peak power of the laser and the duration of interaction. During the interaction, two distinct phenomen…
Migration kinetics of ion-implanted beryllium in glassy carbon
2008
Abstract Migration kinetics of low-concentration implanted 7 Be in glassy carbon has been studied by the modified radiotracer technique at temperatures 1285 °C and 1340 °C. The annealed sample concentration profiles show two distinctive components: (i) Main profile broadening assigned to beryllium trapping in defects during annealing. (ii) Tail parts on both sides of the profile maximum related to faster migration. Of the latter the profile representing bulk diffusion lies on the region free of defect influence and is well described by concentration-independent diffusivity. The features of the concentration profile broadening towards the sample surface indicate partial Be trapping in defect…
Evolution of the microstructure of sputter deposited TaAlON thin films with increasing oxygen partial pressure
2021
Abstract Recently, quaternary oxynitrides of transition metals and aluminum have attracted increasing interest due to their tunable properties. Within the present work, a series of TaAl(O)N films was sputter deposited using constant nitrogen and varying oxygen partial pressures. The films were grown from single element Ta and Al targets. The deposition parameters were adjusted to obtain a Ta/Al atomic ratio of ~50/50 for the oxygen-free film and were held constant for the following depositions, with the exception of the increasing oxygen partial pressure and compensatory decreasing argon partial pressure. Elastic recoil detection analysis revealed oxygen contents of up to ~26 at.%, while th…
Pressure-induced instability of the fergusonite phase of EuNbO4 studied by in situ Raman spectroscopy, x-ray diffraction, and photoluminescence spect…
2020
In this article, we present high-pressure experimental investigations on EuNbO4, an interesting technologically important material, using synchrotron based x-ray powder diffraction, Raman spectroscopy, and europium photoluminescence measurements up to 39.2, 31.6, and 32.4 GPa, respectively. All three techniques show the stability of the ambient monoclinic phase until 20 GPa. Beyond that, a pressure-induced structural phase transition takes place with the coexistence of two phases over a wide pressure range. The structure of the high-pressure phase has been determined as orthorhombic (space group: Imma) with a volume discontinuity of nearly 9% at the transition indicating the nature of trans…
Modeling Stator Winding Inter-Turn Short Circuit Faults in PMSMs including Cross Effects
2020
Author's accepted manuscript. © 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. This paper presents a detailed analysis of stator winding inter-turn Short Circuit (ITSC) faults, taking the cross effects in the three phases of a permanent magnet synchronous motor (PMSM) into account by considering insulation degradation resistances. A PMSM with series coils in eac…
Determining the deformation and resulting coupling efficiency degradation of ultrastable fiber-coupled optical benches under load.
2020
Fiber-coupled optical benches are an integral part of many laser systems. The base of such an optical bench is usually a slab of solid material, onto which optical components are fixed. In many environments, the ability to retain high fiber coupling efficiency under mechanical loads is essential. In this article, we study the fiber-to-fiber coupling efficiency under the application of static mechanical loads experimentally and theoretically: We constructed a simple three-point bending setup to interferometrically measure the deformation of an optical bench under load. Using the same setup, we further recorded the resulting coupling efficiency variations. The examined optical benches are bas…
RBS and ERD cross-sections and optical model parameters for the analysis of lithium, boron and nickel
2000
Abstract Elastic scattering cross-sections for RBS analysis of nickel by 7 Li and 11 B ion backscattering near the Coulomb barrier have been determined. The lithium ion measurements were performed in the energy range of 8–15 MeV at the laboratory angles of 115° and 135°. For boron ions the energies between 14 and 24 MeV and scattering angles of 89°, 110° and 130° were used. For the analysis of lithium and boron by ERD the scattering cross-sections have been calculated by kinematically reversing the backscattering process. The calculated 58 Ni ion energies thus varied between 65 and 125 MeV for lithium and between 75 and 130 MeV for boron recoils. For the Li + Ni and B + Ni systems the thres…
Neutron scattering and imaging: a tool for archaeological studies
2015
International audience; Neutron scattering and neutron imaging are powerful techniques for studying the structure of objects without damage, which is an essential prerequisite for investigations in Cultural Heritage domain, particularly in Archaeology. The deep penetration of neutrons in most materials allows for the study of relatively large objects. The contrast between similar materials, like metals in alloys, or that due to the presence of hydrogen atoms gives information about the internal structure of objects that have been modified or repaired in the past. Imaging and tomography give a 3-dimensional view of the whole object, permitting discrimination between different parts of the ob…
Strategies for numerical simulation of linear friction welding of metals: a review
2017
Linear friction welding (LFW) is a solid-state joining process used to weld non-axisymmetric components. Material joining is obtained through the reciprocating motion of two specimens undergoing an axial force. During this process, the heat source is determined by the frictional work transformed into heat. This results in a local softening of the material and plays a key role in the onset of the bonding conditions. In this paper, a critical analysis of the different approaches used to simulate the LFW processes is provided. The focus of the paper is the comparison of different modeling strategies and the most relevant outputs available, i.e. temperature, strain and stress distribution, mate…
Resistive communications based on neuristors
2017
Memristors are passive elements that allow us to store information using a single element per bit. However, this is not the only utility of the memristor. Considering the physical chemical structure of the element used, the memristor can function at the same time as memory and as a communication unit. This paper presents a new approach to the use of the memristor and develops the concept of resistive communication.