Search results for "Energy conversion efficiency"
showing 10 items of 102 documents
Lead acetate precursor based p-i-n perovskite solar cells with enhanced reproducibility and low hysteresis
2015
A low temperature approach for the fabrication of p-i-n perovskite solar cells is presented. Using lead acetate-based precursors, flat and homogeneous CH3NH3PbI3 films, compatible with the use of thin organic charge transport layers, can be obtained. The corresponding solar cells showed power conversion efficiency up to 12.5%, with remarkable reproducibility and very low hysteresis.
Broadband stimulated Raman backscattering
2016
International audience; Broadband amplification employing stimulated Raman backscattering is demonstrated. Using seed pulses with a bandwidth of about 200 nm, we study the amplification in a wide spectral range in a single laser shot. With chirped pump pulses and a Ne gas jet, we observed under optimized conditions, amplification in a range of about 80 nm, which is sufficient to support the amplification of sub-20 fs pulses. This broad amplification range is also in excellent agreement with PIC simulations. The conversion efficiency is at certain wavelengths as high as 1.2% and was measured to be better than 6×10 −3 on average.
Low-cost high-haze films based on ZnO nanorods for light scattering in thin c-Si solar cells
2015
Light scattering from ZnO nanorods (NR) is investigated, modeled, and applied to a solar cell. ZnO NR (120-1300 nm long, 280-60 nm large), grown by low-cost chemical bath deposition at 90 degrees C, exhibit diffused-to-total transmitted light as high as 70% and 30% in the 400 and 1000 nm wavelength range, respectively. Data and scattering simulation show that ZnO NR length plays a crucial role in light diffusion effect. A transparent ZnO NR film grown on glass and placed on top of a 1 mu m thick c-Si solar cell is shown to enhance the light-current conversion efficiency for wavelengths longer than 600 nm. (C) 2015 AIP Publishing LLC.
Improving Perovskite Solar Cells: Insights From a Validated Device Model
2017
To improve the efficiency of existing perovskite solar cells (PSCs), a detailed understanding of the underlying device physics during their operation is essential. Here, a device model has been developed and validated that describes the operation of PSCs and quantitatively explains the role of contacts, the electron and hole transport layers, charge generation, drift and diffusion of charge carriers and recombination. The simulation to the experimental data of vacuum-deposited CH3NH3PbI3 solar cells over multiple thicknesses has been fit and the device behavior under different operating conditions has been studied to delineate the influence of the external bias, charge-carrier mobilities, e…
A methodology for optimisation of solar dish-Stirling systems size, based on the local frequency distribution of direct normal irradiance
2021
Abstract In geographical areas where direct solar irradiation levels are relatively high, concentrated solar energy systems are one of the most promising green energy technologies. Dish-Stirling systems are those that achieve the highest levels of solar-to-electric conversion efficiency, and yet they are still among the least common commercially available technologies. This paper focuses on a strategy aimed at promoting greater diffusion of dish-Stirling systems, which involves optimizing the size of the collector aperture area based on the hourly frequency distributions of beam irradiance and defining a new incentive scheme with a feed-in tariff that is variable with the installed costs of…
Efficient energy conversion for cubic third-harmonic generation that is phase matched in KTiOPO(4).
2000
We demonstrate, for the first time to our knowledge, that efficient third-harmonic generation can be achieved with a cubic contribution much larger than the quadratic processes. An energy-conversion efficiency of 2.4% is achieved for cubic third-harmonic generation that is phase matched along the x axis of a KTiOPO(4) crystal by use of a picosecond fundamental laser emitting at 1618 nm. The associated cascading processes are only 10% of the pure cubic interaction, which is very suitable for study of the specific quantum optical correlations. Calculations of the third-harmonic generation conversion efficiency with respect to group-velocity dispersion and to the longitudinal Gaussian beam pro…
Second-harmonic generation in surface periodically poled lithium niobate waveguides:On the role of multiphoton absorption
2008
Second harmonic generation is investigated in lithium niobate channels realized by proton exchange and quasi-phase-matched by surface periodic-poling. The reduction in conversion efficiency at high powers is interpreted in terms of multi-photon absorption via two-color terms, yielding an estimate of the dominating three-photon process.
Theoretical analysis of the optimum energy band gap of semiconductors for fabrication of solar cells for applications in higher latitudes locations
2005
In this work some results of theoretical analysis on the selection of optimum band gap semiconductor absorbers for application in either single or multijunction (up to five junctions) solar cells are presented. For calculations days have been taken characterized by various insolation and ambient temperature conditions defined in the draft of the IEC 61836 standard (Performance testing and energy rating of terrestrial photovoltaic modules) as a proposal of representative set of typical outdoor conditions that may influence performance of photovoltaic devices. Besides various irradiance and ambient temperature ranges, these days additionally differ significantly regarding spectral distributio…
Intracavity Frequency Doubling and Difference Frequency Mixing for Pulsed ns Ti:Sapphire Laser Systems at On-Line Radioactive Ion Beam Facilities
2015
Intra-cavity second harmonic generation of a Titanium:sapphire (Ti:sa) laser system has been used to improve the conversion efficiency to the second harmonic. Over the course of several experiments performance data spanning the whole wavelength range of a Ti:sa has been collected, which may be used as a guideline for future experiments. An average output power of up to 3.7 W was achieved, resulting in a conversion efficiency of >75 % to the second harmonic. A wavelength coverage from 340-525 nm has been demonstrated. To extend the wavelength range of the solid state laser system, difference frequency mixing has been applied to the intra-cavity doubled light and the fundamental output of a s…
Theoretical efficiency limits for thermoradiative energy conversion
2015
Published version of an article in the journal: Journal of Applied Physics. Also available from the publisher at: http://dx.doi.org/10.1063/1.4907392 A new method to produce electricity from heat called thermoradiative energy conversion is analyzed. The method is based on sustaining a difference in the chemical potential for electron populations above and below an energy gap and let this difference drive a current through an electric circuit. The difference in chemical potential originates from an imbalance in the excitation and de-excitation of electrons across the energy gap. The method has similarities to thermophotovoltaics and conventional photovoltaics. While photovoltaic cells absorb…