Search results for "Engineering and Technology"
showing 10 items of 16184 documents
A Novel Fault-Tolerant Routing Algorithm for Mesh-of-Tree Based Network-on-Chips
2019
Use of bus architecture based communication with increasing processing elements in System-on-Chip (SoC) leads to severe degradation of performance and speed of the system. This bottleneck is overcome with the introduction of Network-on-Chips (NoCs). NoCs assist in communication between cores on a single chip using router based packet switching technique. Due to miniaturization, NoCs like every Integrated circuit is prone to different kinds of faults which can be transient, intermittent or permanent. A fault in any one component of such a crucial network can degrade performance leaving other components non-usable. This paper presents a novel Fault-Tolerant routing Algorithm for Mesh-of-Tree …
Interface evolution during magnetic pulse welding under extremely high strain rate collision: mechanisms, thermomechanical kinetics and consequences
2020
Abstract Magnetic pulse welding enables to produce perplexing interfacial morphologies due to the complex material response during the high strain rate collision. Thus, a thermomechanical model is used in this study to investigate the formation mechanism of the wake, vortex, swirling and mesoscale cavities with the increase of the impact intensity at the interface. The formation of these interfacial features are difficult to characterize by insitu methods, thus the origin of phenomena still remain a subject of open discussion. Our studies identify the governing mechanisms and the associated thermomechanical kinetics, which are responsible for the formation mechanism of interfacial features.…
Data-driven Fault Diagnosis of Induction Motors Using a Stacked Autoencoder Network
2019
Current signatures from an induction motor are normally used to detect anomalies in the condition of the motor based on signal processing techniques. However, false alarms might occur if using signal processing analysis alone since missing frequencies associated with faults in spectral analyses does not guarantee that a motor is fully healthy. To enhance fault diagnosis performance, this paper proposes a machinelearning based method using in-built motor currents to detect common faults in induction motors, namely inter-turn stator winding-, bearing- and broken rotor bar faults. This approach utilizes single-phase current data, being pre-processed using Welch’s method for spectral density es…
Determination of impurity distributions in ingots of solar grade silicon by neutron activation analysis
2017
AbstractIn a series of crystallization experiments, the directional solidification of silicon was investigated as a low cost path for the production of silicon wafers for solar cells. Instrumental neutron activation analysis was employed to measure the influence of different crystallization parameters on the distribution of 3d-metal impurities of the produced ingots. A theoretical model describing the involved diffusion and segregation processes during the solidification and cooling of the ingots could be verified by the experimental results. By successive etching of the samples after the irradiation, it could be shown that a layer of at least 60 μm of the samples has to be removed to get r…
Refractive index controlled by film morphology and free carrier density in undoped ZnO through sol-pH variation
2018
Abstract Zinc oxide thin films, prepared by the sol-gel process, were deposited on glass substrate using spin coating technique. The sol-pH effect on the optical parameters was studied for alkaline sol. The surface roughness was investigated by atomic force microscopy (AFM) and varied from 20 to 40 nm. The optical transmission measurements were carried out to evaluate the behavior of the extinction coefficient and the refractive index. An exponential decay of the refractive index ‘n’ as a function of wavelength was observed. The refractive index increases slightly when the pH increases to pH = 9.5 where it reaches its maximum. Beyond this value, it decreases sharply. This behavior has been …
Determination of elastoplastic properties of TiO2 thin films deposited on dual phase stainless steel using nanoindentation tests
2010
International audience; In recent years, the extraction of mechanical behaviour of thin films by nanoindentation using sharp indenter geometry has been extensively studied. This work investigates the mechanical properties of TiO2 thin film (1 µm thickness) deposited by spin coating on dual phase Duplex stainless steel and glass substrates. Experiments are carried out with different sharp triangular pyramids (a Cube corner and a Berkovich indenter) using a commercial Nano Indenter® XP apparatus. The substrate effect has been counteracted and an inverse method proposed in literature for bulk material has been adapted to assess the elastoplastic parameters of the tested thin film directly from…
Enhancement of the Spin Pumping Effect by Magnon Confluence Process in YIG/Pt Bilayers
2019
The experimental investigation of the spin pumping process by dipolar‐exchange magnons parametrically excited in in‐plane magnetized yttrium iron garnet/platinum bilayers is presented. The electric voltage generated in the platinum layer via the inverse spin Hall effect (ISHE) results from contributions of two opposite spin currents formed by the longitudinal spin Seebeck effect and by the spin pumping from parametric magnons. In the field‐dependent measurements of the spin pumping‐induced component of the ISHE‐voltage, a clearly visible sharp peak is detected at high pumping powers. It is found that the peak position is determined by the process of confluence of two parametrically excited …
Luminescence characteristics of magnesium aluminate spinel crystals of different stoichiometry
2019
We are grateful to Drs E. Vasil’chenko and A. Maaroos for the help with experiments and useful discussions. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. In addition, the research leading to these results has received funding from the Estonian Research Council Institutional Research Funding IUT02-26.
Two prospective Li-based half-Heusler alloys for spintronic applications based on structural stability and spin–orbit effect
2017
To search for half-metallic materials for spintronic applications, instead of using an expensive trial-and-error experimental scheme, it is more efficient to use first-principles calculations to design materials first, and then grow them. In particular, using a priori information of the structural stability and the effect of the spin–orbit interaction (SOI) enables experimentalists to focus on favorable properties that make growing half-metals easier. We suggest that using acoustic phonon spectra is the best way to address the stability of promising half-metallic materials. Additionally, by carrying out accurate first-principles calculations, we propose two criteria for neglecting the SOI s…
Low complexity digital background calibration algorithm for the correction of timing mismatch in time-interleaved ADCs
2019
Abstract A low-complexity post-processing algorithm to estimate and compensate for timing skew error in a four-channel time-interleaved analog to digital converter (TIADC) is presented in this paper, together with its hardware implementation. The Lagrange interpolator is used as the reconstruction filter which alleviates online interpolator redesign by using a simplified representation of coefficients. Simulation results show that the proposed algorithm can suppress error tones for input signal frequency from 0 to 0.4 f s . The proposed structure has, at least, 41% reduction in the number of required multipliers. Implementation of the algorithm, for a four-channel 10-bit TIADC, show that, f…