Search results for "Fluid dynamics"
showing 10 items of 1005 documents
Hydrodynamics of a three-phase fixed-bed reactor operating in the pulsing flow regime at an elevated pressure
2002
Abstract Results are presented for a three-phase reactor operating at an elevated pressure in the pulsing flow regime. For the system air–water and pressures of 0.1– 0.9 MPa lines are determined that define the change of the hydrodynamic model from the gas continuous flow regime (GCF) to the pulsing flow regime (PF). Also, parameters are found that characterize the pulsing flow of fluids, namely the velocity of pulses travelling along the bed, the frequency of pulsations and their structure, i.e., the length of the pulses and that of the liquid-rich zone.
Modeling of Magnetic-Field-Assisted Fluidization: Model Development and CFD Simulation of Magnetically Stabilized Fluidized Beds
2014
Magnetic-field-assisted fluidization is starting to be considered as a viable alternative to standard fluidized beds for those operations (such as particle separations, filtration, adsorption) in which the solid phase can be made of magnetic particles or, alternatively, the fluidizing agent is a ferro-fluid; thus the fluid bed responds to the action of magnetic fields, and stabilized fluidization regimes can be generated. One of the major difficulties to be tackled is the development of a predictive model capable of estimating the stabilized-to-bubbling transition velocity for a given magnetic field or, on the other hand, the magnetic field intensity required to stabilize the bed to a quies…
Control of flow separation using electromagnetic forces
2003
Introduction If a fluid is electrically conductive, its flow may be controlled using electromagnetic forces. Meanwhile, this technique is a recognized tool even on an industrial scale for handling highly conductive materials like liquid metals. However, also fluids of low electrical conductivity as considered in the present study, like sea--water and other electrolytes, permit electromagnetic flow control. Experimental results on the prevention of flow separation by means of a streamwise, wall parallel Lorentz force acting on the suction side of inclined flat plates and hydrofoils will be presented. Force Configuration The stripwise arrangement of permanent magnets and electrodes of alterna…
Geometric Analysis of Type B Aortic Dissections Shows Aortic Remodeling After Intervention Using Multilayer Stents
2020
Recently, multilayer stents for type B aortic dissections (TBAD) have been proposed to decrease false lumen flow, increase and streamline true lumen flow, and retain branch vessel patency. We aimed to provide a protocol with standardized techniques to investigate aortic remodeling of TBAD by multilayer flow modulators (MFM) in static geometric and hemodynamic analyses. Combining existing literature and new insights, a standardized protocol was designed. Using pre- and postoperative CT scans, geometric models were constructed, lumen dimensions were calculated, computational fluid dynamics (CFD) models were composed, and velocity and pressures were calculated. Sixteen TBAD cases treated with …
Hydrogen and helium films as model systems of wetting
1997
Optical experiments on the wetting properties of liquid 4He and molecular hydrogen are reviewed. Hydrogen films on noble metal surfaces serve as model systems for studying triple point wetting, a continuous transition between wetting and non-wetting. By means of optically excited surface plasmons, the adsorbed film thickness for temperatures around, and far below, the bulk melting temperature is measured, and the physical mechanisms responsible for the transition are elucidated. Possible applications for other experiments in pure and applied research are discussed. Thin films are droplets of liquid helium are studied on cesium surfaces, on which there is a first order wetting transition. Ou…
Relaxation of wet paper by simulations and laboratory-scale experiments
2009
Numerical studies of fiber networks and experiments on wet paper show that tensile force relaxes linearly as a function of logarithmic time. Relaxation rate is faster for wet than dry paper. Simulated permanent deformation after relaxation is clearly higher than that measured in wet paper.
Current-induced fingering instability in magnetic domain walls
2015
The shape instability of magnetic domain walls under current is investigated in a ferromagnetic (Ga,Mn)(As,P) film with perpendicular anisotropy. Domain wall motion is driven by the spin transfer torque mechanism. A current density gradient is found either to stabilize domains with walls perpendicular to current lines or to produce finger-like patterns, depending on the domain wall motion direction. The instability mechanism is shown to result from the non-adiabatic contribution of the spin transfer torque mechanism.
Diffusion Measurements on Crystalline Rock Matrix
1994
AbstractA new gas flow technique is introduced such that experiments on very long samples are possible. This new technique together with increased accuracy of the measurements, allows the observation of power law tails in the break-through curves. Dispersion in these experiments can be controlled in great detail, and therefore the power law tails can be used to determine very accurately the parameters relevant in matrix diffusion. Results for rock and metal samples are shown, and they are fitted with model calculations which include both dispersion and matrix diffusion. The introduced technique, which is designed for ordinary drill cores, is suitable for scanning a large number of samples i…
Wall slip and bulk yielding in soft particle suspensions
2021
We simulate a dense athermal suspension of soft particles sheared between hard walls of a prescribed roughness profile, using a method that fully accounts for the fluid mechanics of the solvent between the particles, and between the particles and the walls, as well as for the solid mechanics of changes in the particle shapes. We thus capture the widely observed phenomenon of elastohydrodynamic wall slip, in which the soft particles become deformed in shear and lift away from the wall slightly, leaving behind a thin lubricating solvent layer of high shear. For imposed stresses below the material's bulk yield stress, we show the observed wall slip to be dominated by this thin solvent layer. A…
Transport properties of heterogeneous materials. Combining computerised X-ray micro-tomography and direct numerical simulations
2009
Feasibility of a method for finding flow permeability of porous materials, based on combining computerised X-ray micro-tomography and numerical simulations, is assessed. The permeability is found by solving fluid flow through the complex 3D pore structures obtained by tomography for actual material samples. We estimate overall accuracy of the method and compare numerical and experimental results. Factors contributing to uncertainty of the method include numerical error arising from the finite resolution of tomographic images and the rather small sample size available with the present tomographic techniques. The total uncertainty of computed values of permeability is, however, not essentiall…