Search results for "Formic acid"
showing 10 items of 108 documents
Vibrational spectroscopy of trans and cis deuterated formic acid (HCOOD): Anharmonic calculations and experiments in argon and neon matrices
2010
The absorption spectra of trans and cis conformers of deuterated formic acid (HCOOD) isolated in argon and neon matrices are analyzed in the mid-infrared and near-infrared spectral regions (7900–450 cm � 1 ). Vibrational excitation by narrow-band IR radiation is used to convert the lower-energy trans conformer to the higher-energy cis form. A large number of overtone and combination bands are identified. The results of anharmonic vibrational calculations (CC-VSCF) for both conformers are reported and compared to the experimental spectra.
Electrochemical conversion of CO2 to formic acid using a Sn based electrode: A critical review on the state-of-the-art technologies and their potenti…
2021
Abstract The electrochemical conversion of carbon dioxide is considered one of the most promising strategies to convert waste-CO2 into value-added chemicals. This review focuses on the synthesis of formic acid/formate in aqueous electrolyte using Sn-based cathodes; this material is considered relatively cheap and shows promising results in terms of faradaic efficiency. In order to be suitable at an industrial scale, the process should present simultaneously high current densities, faradaic efficiencies close to 100%, high concentrations of formic acid and long-term stability. Analysing the main results reported in the literature, it was observed that to date further studies are necessary to…
Electrochemical conversion of CO2 to HCOOH at tin cathode in a pressurized undivided filter-press cell
2018
Abstract The electrochemical reduction of carbon dioxide to formic acid was performed for the first time in a pressurized filter-press cell with a continuous recirculation of the electrolytic solution (0.9 L) at a tin cathode. It was shown that the performances of the system are comparable or slightly better than that of a batch system with a smaller volume (0.05 L). The selection of proper values of both current density and CO2 pressure allowed to achieve quite high values of faradaic efficiencies. Long-time electrolyses have shown that the system is stable and that it can allow to generate quite high concentrations of HCOOH (about 0.4 M).
Development of an Electrochemical Process for the Simultaneous Treatment of Wastewater and the Conversion of Carbon Dioxide to Higher Value Products
2016
Many researchers have shown that selected anodic processes allow effective treatment of a very large amount of wastewater contaminated by pollutants resistant to biological processes. In the meantime, various authors have also shown that carbon dioxide can be converted into higher value products, such as formic acid or synthesis gas, by cathodic reduction at suitable cathodes. These two processes present interesting economic potential that, however, still needs to be improved for further development at an industrial level. Herein, these two kinds of process are combined in the same cell to improve their economic feasibility. In particular, the anodic treatment of wastewater at a boron-doped…
Towards the electrochemical conversion of CO2 to formic acid at an applicative scale: technical and economic analysis of most promising routes
2021
In the last decade, the electrochemical conversion of CO 2 to formic acid, FA, using Sn‐based cathodes, was widely investigated. In this work, the technical feasibility and economic viability of this process were evaluated considering the most promising electrochemical routes reported in the literature. Five case studies, based on the utilisation of GDE technologies or high CO 2 pressures, were analysed. The cost for producing FA by the electrochemical route was compared with that of the conventional chemical route. Several scenarios were envisioned finding the target figures of merit, the potential bottlenecks (including low FA concentration, GDE cost and high energy consumption) of each t…
Low Temperature Growth of High Purity, Low Resistivity Copper Films by Atomic Layer Deposition
2011
The atomic layer deposition of copper metal thin films was achieved using a three precursor sequence entailing Cu(OCHMeCH2NMe2)2, formic acid, and hydrazine. A constant growth rate of 0.47−0.50 A/cycle was observed at growth temperatures between 100 and 170 °C. The resulting films are high purity and have low resistivities.
Matrix Isolation and Ab Initio Study of Trans−Trans and Trans−Cis Dimers of Formic Acid
2010
Six trans-trans and five trans-cis dimeric structures of formic acid (HCOOH) are revealed by ab initio calculations. Four trans-trans and two trans-cis dimers are identified in the IR absorption spectra in argon matrices. The trans-cis dimers are obtained by narrow-band IR excitation of the vibrational transitions of the trans-trans dimers. Two trans-trans (tt3 and tt6) and one trans-cis (tc4) dimer are characterized experimentally for the first time. The tunneling decay rates of two trans-cis dimers (tc1 and tc4) are evaluated at different temperatures. A greater lifetime of the trans-cis dimers at elevated temperatures compared to the cis-monomer suggests that the high-energy conformers c…
Reactive compatibilization of PA6/LDPE blends with an ethylene–acrylic acid copolymer and a low molar mass bis-oxazoline
2003
Abstract A sample of polyamide-6 (PA) was blended with low density polyethylene (LDPE) in the 80/20 wt/wt ratio, either without and with 2 phr of an ethylene–acrylic acid copolymer (EAA), Which was known to behave as a compatibilizer precursor, and the effect of the addition of small amounts (0.2 or 0.35 phr) of a fourth component, 2,2′-(1,3-phenylene)-bis(2-oxazoline) (PBO), was investigated. The reactions of PBO with EAA, PA and their blends were studied by recording as a function of time the torque applied to the blending apparatuses and by studying the solubility behavior of the products in formic acid. The PALDPE blends were prepared in a co-rotating twin screw extruder and were charac…
MODELING OF A TiO2-COATED QUARTZ -WOOL PACKED-BED PHOTOCATALYTIC REACTOR
2010
A fixed-bed, photocatalytic laboratory reactor aimed to degrade pollutants from water streams was designed and built. Quartz wool coated with a thin film of TiO2 was employed as the reactor filling. The photocatalyst was placed in the reactor forming a loose packing to guarantee the intimate contact among reactants, photons, and the photocatalytic surface. This reactor was employed to study the photocatalytic decomposition of a model pollutant (formic acid). A reactor–radiation–reaction model was developed, which was comprised of the reactor mass balance, radiation model, and kinetic model for the degradation of formic acid. The local superficial rate of photon absorption, which was necessa…
Silver Impregnation of Alzheimer's Neurofibrillary Changes Counterstained for Basophilic Material and Lipofuscin Pigment
1988
A method is described in which selective silver staining of Alzheimer's neurofibrillary changes is combined with staining of cell nuclei, Nissl material, and lipofuscin granules. Formalin fixed, paraffin embedded sections of human autopsy tissue are silver stained according to a method proposed by Gallyas. Lipofuscin is stained by crotonaldehyde fuchsin following performic acid oxidation. Nissl substance is visualized by either Darrow red or gallocyanin-chrome alum staining. Architectonic units showing the specific pathology and the neuronal types prone to develop the neurofibrillary changes can be recognized using this technique.