Search results for "HARDNESS"
showing 10 items of 160 documents
Microhardness and adhesion measurements of reactively sputtered TiN/AlN multilayer coatings deposited as function of mass-flow of nitrogen
1998
Abstract Multilayer coatings of (Ti, Al)N x have been deposited by reactive sputtering from Ti and Al targets in a side-by-side configuration on WC and stainless steel substrates. The rotation of the substrate holder varied from 2 to 14 r.p.m. corresponding to a bilayer thickness of 0.8–8 nm. The acoustic emission scratch technique for adhesion measurements was used for studying coating performance, and critical load values for the coatings on WC substrate up to 150 N were obtained. The Vickers microhardness in the load range 0.003–2 N was measured, and in order to obtain true hardness values, an optimal range of indentation depth and coating thickness was determined. Depending on the nitro…
Forces and deformations of the abdominal wall—A mechanical and geometrical approach to the linea alba
2011
Force-elongation responses of the human abdominal wall in the linea alba region were determined by tensile tests in which the linea alba was seen to exhibit a nonlinear elastic, anisotropic behavior as is frequently observed in soft biological tissues. In addition, the geometry of the abdominal wall was determined, based on MRI data. The geometry can be specified by principal radii of curvature in longitudinal of approximately 470 mm and in the transverse direction of about 200 mm. The determined radii agree with values found in other studies. Mechanical stresses, deformations and abdominal pressures for load cases above 6% elongation can be related using Laplace's formula and our constitut…
Physical-mechanical effects of Nd:YAG laser on the surface of sound dental enamel.
1993
Human dental enamel samples were irradiated using a 5 kHz Q-Switched Nd:YAG laser. An increase in Knoop microhardness and modification of the membrane permselectivity were detached. These results and the changes observed by SEM, can be connected with the fusion of the enamel surface.
Could sonic delivery of bulk-fill resins improve the bond strength and cure depth in extended size class I cavities?
2020
Background The implementation of restorative procedures that guarantee success and optimize clinical time is the target of investigations in Restorative Dentistry. This study aimed to analyze the influence of sonic insertion of bulk-fill (BF) and conventional (C) resin composites on the microtensile bond-strength (µ-TBS) and cure depth (CD) of large and deep class I restorations. Material and Methods Fifty-six healthy human premolars were selected and occlusal cavities (4 x 4 x 3 mm; factor C = 5) were prepared. TC - Tetric N-Ceram (BF), SF - SonicFill (BF), and Z350 - Filtek Z350 XT (C) composite resins were used to restore the cavities, using sonic (S) and non-sonic (NS) insertion techniq…
Flexural strength and microhardness of anterior composites after accelerated aging
2016
Background This study aimed to evaluate the flexural strength and microhardness of three different anterior composites after 10 000 thermocycles. Material and Methods The mechanical properties of a nano-fill composite (Filtek Ultimate Universal Restorative (FUR) (Enamel)), a nano-hybrid composite (Clearfil Majesty ES2 (ES2) (Enamel)), and a micro-hybrid composite (G Aenial Anterior (GAA)) were investigated in this study. For the microhardness test, 8-mm diameter and 2-mm thickness composite discs were used (n = 10), and for the flexural strength test, 25x2x2 mm bar-shaped specimens were prepared (n = 13). The specimens were tested at 24 h and after 10 000 thermocycles. Data were analyzed us…
Polymerization and Damage of C60 Single Crystals under Low Fluency Laser Irradiation
2001
Photo-induced hardening, substructure formation and damage of C 60 single crystals under the 632.8 nm He-Ne laser irradiation in air at a power density of 1.47 mW/mm 2 was investigated by microhardness and AFM methods. Photo-induced formation of the dislocation substructure and crystallographically oriented crack patterns on the (111) face due to lattice contraction on polymerization were observed. Two phototransformed states: soft (400-450 MPa) and hard (650-1000 MPa) are found to appear under laser-irradiation. Hard fullerite is created in the subsurface layer < 1 μm at the saturation stage of phototransformation. It softens to 400-450 MPa at 340 K and reverts to non-polymerized state at …
The Use of Atomic Force Microscopy in Determining the Stiffness and Adhesion Force of Human Dentin After Exposure to Bleaching Agents
2009
Introduction: Oxidant bleaching agents may induce several alterations on mineralized teeth tissues. Our aim is to study,at the ultrastructurallevel,mechanicalmodifications induced on dentin after exposure to different bleaching agents.Methods: Nanoindentation performed with atomic force microscopy was used to measure changes in dentin stiffness as well as the adhesion force between the tip and the tissue both in intertubular and peritubulardentin.Foreachspecimen,dentinlocalization, and bleaching agent, 100 independent nanoindentations were performed. Carbamide peroxide (30%) and hydrogenperoxide(35%) wereusedasbleaching agents. Results: A significant reduction of both stiffness and adhesion…
Role of continuous moisture profile monitoring by inline NIR spectroscopy during fluid bed granulation of an Enalapril formulation
2010
Granulation and tableting are closely related process steps in the supply chain of pharmaceutical products. Even today, these steps are still optimized independently by trial and error. On the framework of a process analytical technology approach, these processes were evaluated in an integrated approach. Enalapril maleate is a low-dose drug substance with poor granulating and tableting behavior. In order to verify how granulation influences tableting properties, different granulation experiments were performed.Granulation experiments with fast spraying rate and fast drying as well as fast spraying rate and slow drying, and also combinations of both were run. The obtained granules were then …
Effect of different bleaching protocols on whitening efficiency and enamel superficial microhardness
2018
Background Tooth bleaching is a popular aesthetic treatment to modify the color of teeth. Despite the extensive literature concerning the subject, there is still no consensus regarding the application mode of the different bleaching agents and their effect on enamel. Therefore, this study evaluated the influence of different bleaching protocols on whitening efficiency and enamel superficial hardness. Material and methods Bovine enamel fragments were embedded in acrylic resin and wet-sanded to obtain a flat buccal surface. The specimens were then randomly divided into 6 groups (n=10), based on the bleaching material [HP Maxx 35% (35% hydrogen peroxide), HP Blue 35% (35% hydrogen peroxide + C…
Atmosphere-induced change of microhardness and plasticity of C60 single crystals and polycrystalline films
1998
Abstract The effect of air exposure and visible light illumination on the microhardness, plasticity and dislocation mobility in the C60 single crystals was investigated. Microhardness values for defined structural states of the fullerene (pristine, oxygen-intercalated, photo-oxidized) are reported. It has been shown that oxygen intercalation in the fullerene lattice during air-aging in the dark results in the suppression of dislocation mobility. However, only a slight increase in the hardness of oxygenated samples was observed. A remarkable increase in the hardness and decrease in the plasticity of the C60 crystals under illumination-assisted air exposure was noted. Photochemical transforma…